Cargando…

Effect of Chemical Modification on Mechanical Properties of Wood-Plastic Composite Injection-Molded Parts

Wood chips from furniture-manufacturing byproducts, which do not include adhesive or paint in the waste wood, were used for the flouring process and chemical modification of wood flour (WF). After chemical modification, the WF was mixed with polypropylene through extrusion compounding and injection-...

Descripción completa

Detalles Bibliográficos
Autores principales:	Sohn, Joo Seong, Cha, Sung Woon
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2018
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC6401952/ https://www.ncbi.nlm.nih.gov/pubmed/30961316 http://dx.doi.org/10.3390/polym10121391

Ejemplares similares

Shrinkage and Warpage Minimization of Glass-Fiber-Reinforced Polyamide 6 Parts by Microcellular Foam Injection Molding
por: Ryu, Youngjae, et al.
Publicado: (2020)

Effect of Aluminum Flakes on Mechanical and Optical Properties of Foam Injection Molded Parts
por: Kim, Donghwi, et al.
Publicado: (2021)

Warpage Reduction of Glass Fiber Reinforced Plastic Using Microcellular Foaming Process Applied Injection Molding
por: Kim, Hyun Keun, et al.
Publicado: (2019)

Morphological and Mechanical Properties of Bilayers Wood-Plastic Composites and Foams Obtained by Rotational Molding
por: Vázquez Fletes, Roberto Carlos, et al.
Publicado: (2020)

Interfacial Adhesion and Mechanical Properties of Wood-Polymer Hybrid Composites Prepared by Injection Molding
por: Stadlmann, Alexander, et al.
Publicado: (2021)

Investigation of Wood Flour Size, Aspect Ratios, and Injection Molding Temperature on Mechanical Properties of Wood Flour/Polyethylene Composites
por: Golmakani, Mohammad E., et al.
Publicado: (2021)

The Effect of Varying the Amount of Short Hemp Fibers on Mechanical and Thermal Properties of Wood–Plastic Composites from Biobased Polyethylene Processed by Injection Molding
por: Dolçà, Celia, et al.
Publicado: (2021)

Thermoelasticity of Injection-Molded Parts
por: Turk, Janez, et al.
Publicado: (2023)

Effects of Injection Molding Parameters on Properties of Insert-Injection Molded Polypropylene Single-Polymer Composites
por: Wang, Jian, et al.
Publicado: (2021)

Properties of Injection Molded Biocomposites Reinforced with Wood Particles of Short-Rotation Aspen and Willow
por: Kumar, Anuj, et al.
Publicado: (2020)

Comparison of the Physico-Mechanical and Weathering Properties of Wood–Plastic Composites Made of Wood Fibers from Discarded Parts of Pomelo Trees and Polypropylene
por: Hung, Ke-Chang, et al.
Publicado: (2021)

Thermal Properties of Wood-Plastic Composites with Different Compositions
por: Guo, Yong, et al.
Publicado: (2019)

Injection Molding Plastic Solar Cells
por: Burgués‐Ceballos, Ignasi, et al.
Publicado: (2023)

Mechanical Properties Variation in Wood—Plastic Composites with a Mixed Wood Fiber Size
por: Xu, Hailong, et al.
Publicado: (2023)

An Injecting Molding Method for Forming the HFRP/PA6 Composite Parts
por: Xu, Bin, et al.
Publicado: (2022)

Thermal, Mechanical, Morphological and Aesthetical Properties of Rotational Molding PE/Pine Wood Sawdust Composites
por: Martins, Carla I., et al.
Publicado: (2022)

Industry 4.0 In-Line AI Quality Control of Plastic Injection Molded Parts
por: Aminabadi, Saeid Saeidi, et al.
Publicado: (2022)

Reducing the Burn Marks on Injection-Molded Parts by External Gas-Assisted Injection Molding
por: Li, Jiquan, et al.
Publicado: (2021)

Effect of chemical treatments on properties of injection molded Nypa fruticans fiber reinforced polypropylene composite
por: Hasan, Afnan, et al.
Publicado: (2022)

Effects of Matrix Modification on the Mechanical Properties of Wood–Polypropylene Composites
por: Yi, Shunmin, et al.
Publicado: (2017)

Mechanical Properties of Injection Molded PP/PET-Nanofibril Composites and Foams
por: Mark, Lun Howe, et al.
Publicado: (2022)

Properties of Wood–Plastic Composites Manufactured from Two Different Wood Feedstocks: Wood Flour and Wood Pellets
por: Pokhrel, Geeta, et al.
Publicado: (2021)

A Review on Flexural Properties of Wood-Plastic Composites
por: Jian, Bingyu, et al.
Publicado: (2022)

Modification of the Cavity of Plastic Injection Molds: A Brief Review of Materials and Influence on the Cooling Rates
por: Carrupt, Maria C., et al.
Publicado: (2021)

Modeling and Analysis of Morphology of Injection Molding Polypropylene Parts Induced by In-Mold Annealing
por: Salomone, Rita, et al.
Publicado: (2022)

Effects of Biological and Chemical Degradation on the Properties of Scots Pine Wood—Part I: Chemical Composition and Microstructure of the Cell Wall
por: Broda, Magdalena, et al.
Publicado: (2022)

Analysis of the Stress Field in Photoelasticity Used to Evaluate the Residual Stresses of a Plastic Injection-Molded Part
por: Vargas-Isaza, Carlos, et al.
Publicado: (2023)

Analysis of Creep Properties and Factors Affecting Wood Plastic Composites
por: Feng, Li, et al.
Publicado: (2022)

Texturing Technologies for Plastics Injection Molding: A Review
por: Masato, Davide, et al.
Publicado: (2022)

Effect of the Addition of Carbon Nanomaterials on Electrical and Mechanical Properties of Wood Plastic Composites
por: Zhang, Xingli, et al.
Publicado: (2017)

Nanomaterials and Chemical Modifications for Enhanced Key Wood Properties: A Review
por: Papadopoulos, Antonios N., et al.
Publicado: (2019)

Optimization of the Reduction of Shrinkage and Warpage for Plastic Parts in the Injection Molding Process by Extended Adaptive Weighted Summation Method
por: Hiyane-Nashiro, Guillermo, et al.
Publicado: (2022)

Post-Molding Shrinkage, Structure and Properties of Cellular Injection-Molded Polypropylene
por: Kościuszko, Artur, et al.
Publicado: (2022)

Silane-Functionalized Sheep Wool Fibers from Dairy Industry Waste for the Development of Plasticized PLA Composites with Maleinized Linseed Oil for Injection-Molded Parts
por: Pawlak, Franciszek, et al.
Publicado: (2020)

The Effect of Carbon Nanotubes on the Mechanical Properties of Wood Plastic Composites by Selective Laser Sintering
por: Zhang, Yunhe, et al.
Publicado: (2017)

Evaluation of the Mechanical, Thermal and Rheological Properties of Hop, Hemp and Wood Fiber Plastic Composites
por: Talcott, Sierra, et al.
Publicado: (2023)

Investigation of the Mechanical Properties of Parts Fabricated with Ultrasonic Micro Injection Molding Process Using Polypropylene Recycled Material
por: Gaxiola-Cockburn, Rafael, et al.
Publicado: (2020)

Injection Molding of 3-3 Hydroxyapatite Composites
por: Biggemann, Jonas, et al.
Publicado: (2020)

The Effect of Injection Molding Temperature on the Morphology and Mechanical Properties of PP/PET Blends and Microfibrillar Composites
por: Kuzmanović, Maja, et al.
Publicado: (2016)

Investigation of the Warpage of a High-Density Polyethylene Pallet by Plastic Injection Compression Molding: Part I—Numerical Approach
por: Cheng, Chun-Der, et al.
Publicado: (2022)

Cannot write session to /tmp/vufind_sessions/sess_q7ka12o8j8jjc4gla91t67mv4m