Cargando…

Strength of PLA Components Fabricated with Fused Deposition Technology Using a Desktop 3D Printer as a Function of Geometrical Parameters of the Process

The current paper studies the influence of geometrical parameters of the fused deposition modeling (FDM)—fused filament fabrication (FFF) 3D printing process on printed part strength for open source desktop 3D printers and the most popular material used for that purpose—i.e., polylactic acid (PLA)....

Descripción completa

Detalles Bibliográficos
Autores principales:	Kuznetsov, Vladimir E., Solonin, Alexey N., Urzhumtsev, Oleg D., Schilling, Richard, Tavitov, Azamat G.
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2018
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC6414919/ https://www.ncbi.nlm.nih.gov/pubmed/30966348 http://dx.doi.org/10.3390/polym10030313

Ejemplares similares

Design and Fabrication of Strong Parts from Poly (Lactic Acid) with a Desktop 3D Printer: A Case with Interrupted Shell
por: Kuznetsov, Vladimir E., et al.
Publicado: (2019)

Desktop Fabrication of Strong Poly (Lactic Acid) Parts: FFF Process Parameters Tuning
por: Kuznetsov, Vladimir E., et al.
Publicado: (2019)

Hardware Factors Influencing Strength of Parts Obtained by Fused Filament Fabrication
por: Kuznetsov, Vladimir E., et al.
Publicado: (2019)

The Transferability and Design of Commercial Printer Settings in PLA/PBAT Fused Filament Fabrication
por: Wang, Sisi, et al.
Publicado: (2020)

Study of Microchannels Fabricated Using Desktop Fused Deposition Modeling Systems
por: Rehmani, Muhammad Asif Ali, et al.
Publicado: (2020)

Fabrication of cerebral aneurysm simulator with a desktop 3D printer
por: Liu, Yu, et al.
Publicado: (2017)

Fabrication of low cost soft tissue prostheses with the desktop 3D printer
por: He, Yong, et al.
Publicado: (2014)

Utilization of desktop 3D printer-fabricated “Cost-Effective” 3D models in orthognathic surgery
por: Narita, Masato, et al.
Publicado: (2020)

Filament Advance Detection Sensor for Fused Deposition Modelling 3D Printers
por: Soriano Heras, Enrique, et al.
Publicado: (2018)

Mechanical and Geometric Performance of PLA-Based Polymer Composites Processed by the Fused Filament Fabrication Additive Manufacturing Technique
por: Reverte, José María, et al.
Publicado: (2020)

Large volume syringe pump extruder for desktop 3D printers
por: Pusch, Kira, et al.
Publicado: (2018)

Modification of Commercial 3D Fused Deposition Modeling Printer for Extrusion Printing of Hydrogels
por: Koltsov, Semyon I., et al.
Publicado: (2022)

Designing of PLA scaffolds for bone tissue replacement fabricated by ordinary commercial 3D printer
por: Gregor, Aleš, et al.
Publicado: (2017)

Development of Antimicrobial PLA Composites for Fused Filament Fabrication
por: Brounstein, Zachary, et al.
Publicado: (2021)

Preparation of Hydrophobic Surface on PLA and ABS by Fused Deposition Modeling
por: Yang, Huadong, et al.
Publicado: (2020)

Thermoforming Characteristics of PLA/TPU Multi-Material Specimens Fabricated with Fused Deposition Modelling under Different Temperatures
por: Sorimpuk, Neilson Peter, et al.
Publicado: (2022)

Investigating the Material Properties and Microstructural Changes of Fused Filament Fabricated PLA and Tough-PLA Parts
por: Naveed, Nida
Publicado: (2021)

Emission of particulate matter from a desktop three-dimensional (3D) printer
por: Yi, Jinghai, et al.
Publicado: (2016)

Multi-metal 4D printing with a desktop electrochemical 3D printer
por: Chen, Xiaolong, et al.
Publicado: (2019)

Cytotoxicity and Characterization of Ultrafine Particles from Desktop Three-Dimensional Printers with Multiple Filaments
por: Fang, Runcheng, et al.
Publicado: (2023)

Electrical and Thermal Conductivity of Polylactic Acid (PLA)-Based Biocomposites by Incorporation of Nano-Graphite Fabricated with Fused Deposition Modeling
por: Guo, Rui, et al.
Publicado: (2019)

In-vitro evaluation of Polylactic acid (PLA) manufactured by fused deposition modeling
por: Wurm, Matthias C., et al.
Publicado: (2017)

Fused Filament Deposition of PLA: The Role of Interlayer Adhesion in the Mechanical Performances
por: Liparoti, Sara, et al.
Publicado: (2021)

Weld Strength of Friction Welding of Dissimilar Polymer Rods Fabricated by Fused Deposition Modeling
por: Kuo, Chil-Chyuan, et al.
Publicado: (2022)

Experimental investigation on fatigue life and tensile strength of carbon fiber-reinforced PLA composites based on fused deposition modeling
por: Kargar, Ehsan, et al.
Publicado: (2023)

Thermal Properties and In Vitro Biodegradation of PLA-Mg Filaments for Fused Deposition Modeling
por: Leonés, Adrián, et al.
Publicado: (2023)

Performance Analysis of Colored PLA Products with a Fused Filament Fabrication Process
por: Spina, Roberto
Publicado: (2019)

Experimental Validation of Plastic Mandible Models Produced by a “Low-Cost” 3-Dimensional Fused Deposition Modeling Printer
por: Maschio, Federico, et al.
Publicado: (2016)

Additive Analytics: Easy Transformation of Low-Cost Fused Deposition Modeling Three-Dimensional Printers for HPTLC Sample Application
por: Woortman, Dirk Volker, et al.
Publicado: (2020)

Accessing individual 75-micron diameter nozzles of a desktop inkjet printer to dispense picoliter droplets on demand
por: Waasdorp, Rick, et al.
Publicado: (2018)

Accuracy of five different 3D printing workflows for dental models comparing industrial and dental desktop printers
por: Morón-Conejo, Belén, et al.
Publicado: (2022)

Determination of Material Requirements for 3D Gel Food Printing Using a Fused Deposition Modeling 3D Printer
por: In, Jiwon, et al.
Publicado: (2021)

Effects of Accelerating the Ageing of 1D PLA Filaments after Fused Filament Fabrication
por: Orellana-Barrasa, Jaime, et al.
Publicado: (2022)

Effect of Printing Parameters on Mechanical Behaviour of PLA-Flax Printed Structures by Fused Deposition Modelling
por: Belarbi, Yassine Elias, et al.
Publicado: (2021)

Effective Stiffness of Fused Deposition Modeling Infill Lattice Patterns Made of PLA-Wood Material
por: Cuan-Urquizo, Enrique, et al.
Publicado: (2022)

Comparison of axon extension: PTFE versus PLA formed by a 3D printer
por: Kawai, Naofumi, et al.
Publicado: (2022)

A Feasibility Study of Processing Polydimethylsiloxane–Sodium Carboxymethylcellulose Composites by a Low-Cost Fused Deposition Modeling 3D Printer
por: Calcagnile, Paola, et al.
Publicado: (2018)

Ultra-Low-Cost 3D Bioprinting: Modification and Application of an Off-the-Shelf Desktop 3D-Printer for Biofabrication
por: Kahl, Melanie, et al.
Publicado: (2019)

Continuous fiber extruder for desktop 3D printers toward long fiber embedded hydrogel 3D printing
por: Sun, Wenhuan, et al.
Publicado: (2022)

The Influence of Raster Angle and Moisture Content on the Mechanical Properties of PLA Parts Produced by Fused Deposition Modeling
por: Algarni, Mohammed
Publicado: (2021)

Cannot write session to /tmp/vufind_sessions/sess_5cein4f65v4q3imc6m2n7nirbi