Cargando…

Influence of Manufacturing Parameters on Mechanical Properties of Porous Materials by Selective Laser Sintering

This paper presents a study on the tensile properties of Alumide and polyamide PA2200 standard samples produced by Additive manufacturing (AM) based on selective laser sintering (SLS). Because of the orthogonal trajectories of the laser beam during exposure, different orientations of the samples may...

Descripción completa

Detalles Bibliográficos
Autores principales:	Stoia, Dan Ioan, Linul, Emanoil, Marsavina, Liviu
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2019
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC6471919/ https://www.ncbi.nlm.nih.gov/pubmed/30875894 http://dx.doi.org/10.3390/ma12060871

Ejemplares similares

Correlations between Process Parameters and Outcome Properties of Laser-Sintered Polyamide
por: Stoia, Dan Ioan, et al.
Publicado: (2019)

Mode I Fracture Toughness of Polyamide and Alumide Samples obtained by Selective Laser Sintering Additive Process
por: Stoia, Dan Ioan, et al.
Publicado: (2020)

Is Fracture Toughness of PUR Foams a Material Property? A Statistical Approach
por: Pugna, Adrian, et al.
Publicado: (2020)

On the Lateral Compressive Behavior of Empty and Ex-Situ Aluminum Foam-Filled Tubes at High Temperature
por: Linul, Emanoil, et al.
Publicado: (2018)

Poisson’s Ratio of Closed-Cell Aluminium Foams
por: Kováčik, Jaroslav, et al.
Publicado: (2018)

Manufacturing Technologies of Carbon/Glass Fiber-Reinforced Polymer Composites and Their Properties: A Review
por: Rajak, Dipen Kumar, et al.
Publicado: (2021)

Fiber-Reinforced Polymer Composites: Manufacturing, Properties, and Applications
por: Rajak, Dipen Kumar, et al.
Publicado: (2019)

Selective Laser Sintering of Porous Silica Enabled by Carbon Additive
por: Chang, Shuai, et al.
Publicado: (2017)

Research on the Influence of the Manufacturing Process Conditions of Iron Sintered with the Addition of Layered Lubricating Materials on its Selected Properties
por: Urbaniak, Wieslaw, et al.
Publicado: (2020)

Sintering of nanocrystalline materials: Sintering parameters
por: Babalola, Bukola Joseph, et al.
Publicado: (2023)

Tribological Properties of Glass Bead-Filled Polyamide 12 Composite Manufactured by Selective Laser Sintering
por: Gadelmoula, Abdelrasoul, et al.
Publicado: (2023)

Influence of Atmospheric Conditions on Mechanical Properties of Polyamide with Different Content of Recycled Material in Selective Laser Sintering
por: Pilipović, Ana, et al.
Publicado: (2022)

Process Phenomena and Material Properties in Selective Laser Sintering of Polymers: A Review
por: Lupone, Federico, et al.
Publicado: (2021)

Processing of Syndiotactic Polystyrene to Microspheres for Part Manufacturing through Selective Laser Sintering
por: Mys, Nicolas, et al.
Publicado: (2016)

Compressive Behavior of Aluminum Microfibers Reinforced Semi-Rigid Polyurethane Foams
por: Linul, Emanoil, et al.
Publicado: (2018)

Influence of the Printing Angle and Load Direction on Flexure Strength in 3D Printed Materials for Provisional Dental Restorations
por: Derban, Paula, et al.
Publicado: (2021)

Hybrid Approaches for Selective Laser Sintering by Building on Dissimilar Materials
por: Goetzendorfer, Babette, et al.
Publicado: (2020)

Modelling and Microstructural Characterization of Sintered Metallic Porous Materials
por: Depczynski, Wojciech, et al.
Publicado: (2016)

Fabrication of Porous Hydrogenation Catalysts by a Selective Laser Sintering 3D Printing Technique
por: Lahtinen, Elmeri, et al.
Publicado: (2019)

Correlation between properties and microstructure of laser sintered porous β-tricalcium phosphate bone scaffolds
por: Shuai, Cijun, et al.
Publicado: (2013)

Fabrication of Porous Materials by Spark Plasma Sintering: A Review
por: Dudina, Dina V., et al.
Publicado: (2019)

Influence of Sintering Parameters on Spectroscopic Properties of BMW: Eu(3+) Ceramic Materials Prepared by HPLT Technique
por: Miniajluk-Gaweł, Natalia, et al.
Publicado: (2022)

Influence of Selective Laser Melting Additive Manufacturing Parameters in Inconel 718 Superalloy
por: Kladovasilakis, Nikolaos, et al.
Publicado: (2022)

Development of SiC/PVB Composite Powders for Selective Laser Sintering Additive Manufacturing of SiC
por: Zhou, Peng, et al.
Publicado: (2018)

Thermal Influence of CNT on the Polyamide 12 Nanocomposite for Selective Laser Sintering
por: Bai, Jiaming, et al.
Publicado: (2015)

Microstructures and Properties of Porous Liquid-Phase-Sintered SiC Ceramic by Hot Press Sintering
por: Li, Yajie, et al.
Publicado: (2019)

Investigation of the Effects of Roller Spreading Parameters on Powder Bed Quality in Selective Laser Sintering
por: Xiao, Xiangwu, et al.
Publicado: (2022)

Manufacturing of Porous Glass by Femtosecond Laser Welding
por: Tan, Hua, et al.
Publicado: (2022)

A QbD Approach for Evaluating the Effect of Selective Laser Sintering Parameters on Printability and Properties of Solid Oral Forms
por: Gueche, Yanis A., et al.
Publicado: (2021)

Material Evaluation and Process Optimization of CNT-Coated Polymer Powders for Selective Laser Sintering
por: Yuan, Shangqin, et al.
Publicado: (2016)

Laser Micro-Texturing of Sintered Tool Materials Surface
por: Pakuła, Daniel, et al.
Publicado: (2019)

Influence of abrasives and graphite on processing and properties of sintered metallic friction materials
por: Pérez, B., et al.
Publicado: (2019)

Digital Manufacturing of Selective Porous Barriers in Microchannels Using Multi-Material Stereolithography
por: Kim, Yong Tae, et al.
Publicado: (2018)

Optimization of Piezoresistive Response of Elastomeric Porous Structures Based on Carbon-Based Hybrid Fillers Created by Selective Laser Sintering
por: Rollo, Gennaro, et al.
Publicado: (2023)

Anisotropic Compressive Behavior of Metallic Foams under Extreme Temperature Conditions
por: Khezrzadeh, Omid, et al.
Publicado: (2020)

A Review on Synthetic Fibers for Polymer Matrix Composites: Performance, Failure Modes and Applications
por: Rajak, Dipen Kumar, et al.
Publicado: (2022)

Influence of Selective Laser Melting Technological Parameters on the Mechanical Properties of Additively Manufactured Elements Using 316L Austenitic Steel
por: Kluczyński, Janusz, et al.
Publicado: (2020)

Microstructure Evolution and Mechanical Properties Improvement in Liquid-Phase-Sintered Hydroxyapatite by Laser Sintering
por: Duan, Songlin, et al.
Publicado: (2015)

Influence of Thermal Annealing on the Sinterability of Different Grades of Polylactide Microspheres Dedicated for Laser Sintering
por: Gazińska, Małgorzata, et al.
Publicado: (2021)

Experimental Evaluation of Polyphenylsulfone (PPSF) Powders as Fire-Retardant Materials for Processing by Selective Laser Sintering
por: Lv, Yifan, et al.
Publicado: (2021)

Cannot write session to /tmp/vufind_sessions/sess_4g9s4k8brb0rpg8qgdgj1oq6g9