Cargando…

Characterization of Microchannel Replicability of Injection Molded Electrophoresis Microfluidic Chips

Microfluidic chips have been widely applied in biochemical analysis, DNA sequencing, and disease diagnosis due to their advantages of miniaturization, low consumption, rapid analysis, and automation. Injection molded microfluidic chips have attracted great attention because of their short processing...

Descripción completa

Detalles Bibliográficos
Autores principales:	Jiang, Bingyan, Zhu, Laiyu, Min, Liping, Li, Xianglin, Zhai, Zhanyu, Drummer, Dietmar
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2019
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC6523880/ https://www.ncbi.nlm.nih.gov/pubmed/30960592 http://dx.doi.org/10.3390/polym11040608

Ejemplares similares

Thermal Conductivity of Aluminosilicate- and Aluminum Oxide-Filled Thermosets for Injection Molding: Effect of Filler Content, Filler Size and Filler Geometry
por: Zhao, Yang, et al.
Publicado: (2018)

Effect of Interfacial Interaction on the Demolding Deformation of Injection Molded Microfluidic Chips
por: Wang, Yilei, et al.
Publicado: (2022)

Investigation of Solvent-Assisted In-Mold Bonding of Cyclic Olefin Copolymer (COC) Microfluidic Chips
por: Li, Qiang, et al.
Publicado: (2022)

Molecular Dynamics Simulation on the Effect of Bonding Pressure on Thermal Bonding of Polymer Microfluidic Chip
por: Zhou, Mingyong, et al.
Publicado: (2019)

Tensile Creep Behavior of Quasi-Unidirectional E-Glass Fabric Reinforced Polypropylene Composite
por: Zhai, Zhanyu, et al.
Publicado: (2018)

Nonlinear Material Model for Quasi-Unidirectional Woven Composite Accounting for Viscoelastic, Viscous Deformation, and Stiffness Reduction
por: Zhai, Zhanyu, et al.
Publicado: (2018)

Influence of Diamond-Like Carbon Coating on the Channel Deformation of Injection-Molded Microfluidic Chips during the Demolding Process
por: Wang, Yilei, et al.
Publicado: (2020)

A new fuzzy rule based multi-objective optimization method for cross-scale injection molding of protein electrophoresis microfluidic chips
por: Shan, Zhiying, et al.
Publicado: (2022)

The Effect of Temperature and Strain Rate on the Interfacial Behavior of Glass Fiber Reinforced Polypropylene Composites: A Molecular Dynamics Study
por: Zhang, Muhan, et al.
Publicado: (2019)

Replicability of Ultrasonic Molding for Processing Thin-Wall Polystyrene Plates with a Microchannel
por: Ferrer, I., et al.
Publicado: (2018)

Possibilities of Integrated Fabrication of Insulation Systems in Electric Drives by Injection Molding of Thermosets
por: Rösel, Uta, et al.
Publicado: (2022)

High-Precision Thin Wall Bipolar Plates for Fuel Cell Applications via Injection Compression Molding with Dynamic Mold Temperature Control
por: Roth, Benedikt, et al.
Publicado: (2022)

Analysis of microsatellite instability in colorectal carcinoma by microfluidic-based chip electrophoresis
por: Odenthal, M, et al.
Publicado: (2009)

Fabricating Microstructures on Glass for Microfluidic Chips by Glass Molding Process
por: Wang, Tao, et al.
Publicado: (2018)

Molecular Dynamics Simulation on the Interfacial Behavior of Over-Molded Hybrid Fiber Reinforced Thermoplastic Composites
por: Jiang, Bingyan, et al.
Publicado: (2020)

Application and Optimization of the Thin Electric Heater in Micro-Injection Mold for Micropillars
por: Weng, Can, et al.
Publicado: (2022)

Study on Improving Thickness Uniformity of Microfluidic Chip Mold in the Electroforming Process
por: Du, Liqun, et al.
Publicado: (2016)

Liquid plug propagation in computer-controlled microfluidic airway-on-a-chip with semi-circular microchannels
por: Viola, Hannah L., et al.
Publicado: (2023)

Electrophoresis in Microfluidic Systems
por: Ugaz, Victor M., et al.
Publicado: (2007)

Improving the Integrated Fabrication of Insulation Systems in Electric Drives by Injection Molding of Thermosets Due to Processing Conditions and Slot Design
por: Rösel, Uta, et al.
Publicado: (2023)

3D-glass molds for facile production of complex droplet microfluidic chips
por: Tovar, Miguel, et al.
Publicado: (2018)

Fabrication of Different Microchannels by Adjusting the Extrusion Parameters for Sacrificial Molds
por: Tang, Wenlai, et al.
Publicado: (2019)

Application of microfluidic chip electrophoresis for high-throughput nucleic acid fluorescence fragment analysis assays
por: Sun, Yali, et al.
Publicado: (2023)

Observation Interface of PDMS Membrane in a Microfluidic Chip Based on One-Step Molding
por: Chen, Xiangyu, et al.
Publicado: (2017)

Simulation Approach for Hydrophobicity Replication via Injection Molding
por: Baldi-Boleda, Tomás, et al.
Publicado: (2021)

Autonomous microfluidic capillaric circuits replicated from 3D-printed molds
por: Olanrewaju, A. O., et al.
Publicado: (2016)

Cell Injection Millirobot Development and Evaluation in Microfluidic Chip
por: Feng, Lin, et al.
Publicado: (2018)

Integrated magneto–electrophoresis microfluidic chip purification on library preparation device for preimplantation genetic testing for aneuploidy detection
por: Schneider, Lindsay, et al.
Publicado: (2021)

Dual Sacrificial Molding: Fabricating 3D Microchannels with Overhang and Helical Features
por: Goh, Wei Huang, et al.
Publicado: (2018)

Characterization of PDMS Microchannels Using Horizontally or Vertically Formed 3D-Printed Molds by Digital Light Projection
por: Han, Dong Hyun, et al.
Publicado: (2023)

Fabrication and Evaluation of Tubule-on-a-Chip with RPTEC/HUVEC Co-Culture Using Injection-Molded Polycarbonate Chips
por: Lee, Ju-Bi, et al.
Publicado: (2022)

Experimental Analysis of Laser Micromachining of Microchannels in Common Microfluidic Substrates
por: Konari, Prashanth Reddy, et al.
Publicado: (2021)

Enhanced Injection Molding Simulation of Advanced Injection Molds
por: Zink, Béla, et al.
Publicado: (2017)

Study on the Mechanism of Interfacial Friction Heating in Polymer Ultrasonic Plasticization Injection Molding Process
por: Peng, Tao, et al.
Publicado: (2019)

Replication of a Printed Volatile Mold: a novel microfabrication method for advanced microfluidic systems
por: Brossard, Rémy, et al.
Publicado: (2019)

Experimental Study of Injection Molding Replicability for the Micro Embossment of the Ultrasonic Vibrator
por: Zhu, Tieli, et al.
Publicado: (2022)

Molecular Dynamics Study on the Deformation Behaviors of Nanostructures in the Demolding Process of Micro-Injection Molding
por: Weng, Can, et al.
Publicado: (2019)

DNA molecule stretching through thermo-electrophoresis and thermal convection in a heated converging-diverging microchannel
por: Hsieh, Shou-Shing, et al.
Publicado: (2013)

Fast Start-Up Microfluidic Microbial Fuel Cells With Serpentine Microchannel
por: Luo, Xian, et al.
Publicado: (2018)

Tuning Power Ultrasound for Enhanced Performance of Thermoplastic Micro-Injection Molding: Principles, Methods, and Performances
por: Zhao, Baishun, et al.
Publicado: (2021)

Cannot write session to /tmp/vufind_sessions/sess_8u2j95povt719gjg3rrseik130