Cargando…

Direct Synthesis of Fe-Al Alloys from Elemental Powders Using Laser Engineered Net Shaping

The laser engineered net shaping (LENS®) process is shown here as an alternative to melting, casting, and powder metallurgy for manufacturing iron aluminides. This technique was found to allow for the production of FeAl and Fe(3)Al phases from mixtures of elemental iron and aluminum powders. The in...

Descripción completa

Detalles Bibliográficos
Autores principales:	Pęska, Magda, Karczewski, Krzysztof, Rzeszotarska, Magdalena, Polański, Marek
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2020
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC7040837/ https://www.ncbi.nlm.nih.gov/pubmed/31979020 http://dx.doi.org/10.3390/ma13030531

Ejemplares similares

Synthesis of Fe-Al-Ti Based Intermetallics with the Use of Laser Engineered Net Shaping (LENS)
por: Kwiatkowska, Monika, et al.
Publicado: (2015)

On the Influence of Manufacturing Parameters on the Microstructure, Mechanical Properties and Corrosion Resistance of AISI 316L Steel Deposited by Laser Engineered Net Shaping (LENS(®))
por: Rzeszotarska, Magdalena, et al.
Publicado: (2023)

Fabrication of MnCuNiFe–CuAlNiFeMn Gradient Alloy by Laser Engineering Net Shaping System
por: Yan, Kuo, et al.
Publicado: (2022)

Hydrogen Sorption Behavior of Cast Ag-Mg Alloys
por: Dębski, Adam, et al.
Publicado: (2021)

Calorimetric Studies of Magnesium-Rich Mg-Pd Alloys
por: Dębski, Adam, et al.
Publicado: (2021)

The Microstructure Evolution of a Fe(3)Al Alloy during the LENS Process
por: Karczewski, Krzysztof, et al.
Publicado: (2018)

Amino Acids Aided Sintering for the Formation of Highly Porous FeAl Intermetallic Alloys
por: Karczewski, Krzysztof, et al.
Publicado: (2017)

Microstructural Variations in Laser Powder Bed Fused Al–15%Fe Alloy at Intermediate Temperatures
por: Wang, Wenyuan, et al.
Publicado: (2022)

Characterization of Cobalt-Based Stellite 6 Alloy Coating Fabricated by Laser-Engineered Net Shaping (LENS)
por: Durejko, Tomasz, et al.
Publicado: (2021)

Laser Powder-Bed Fusion as an Alloy Development Tool: Parameter Selection for In-Situ Alloying Using Elemental Powders
por: Shoji Aota, Leonardo, et al.
Publicado: (2020)

Additive Manufacturing of β-NiAl by Means of Laser Metal Deposition of Pre-Alloyed and Elemental Powders
por: Müller, Michael, et al.
Publicado: (2021)

Designing for Shape Memory in Additive Manufacturing of Cu–Al–Ni Shape Memory Alloy Processed by Laser Powder Bed Fusion
por: Pérez-Cerrato, Mikel, et al.
Publicado: (2022)

Laser Surface Modification of Aluminium Alloy AlMg9 with B(4)C Powder
por: Sroka, Marek, et al.
Publicado: (2020)

Mechanical Properties Study of Fe-Mn-Si Shape Memory Alloys Welding Seam Formed by Laser Welding with Filler Powder
por: Ju, Heng, et al.
Publicado: (2018)

Superelastic Behavior of Ti-Nb Alloys Obtained by the Laser Engineered Net Shaping (LENS) Technique
por: Kalita, Damian, et al.
Publicado: (2020)

The effect of alloying elements on the properties of pressed and non-pressed biodegradable Fe–Mn–Ag powder metallurgy alloys
por: Caligari Conti, Malcolm, et al.
Publicado: (2019)

Laser Engineered Net Shaping of Nickel-Based Superalloy Inconel 718 Powders onto AISI 4140 Alloy Steel Substrates: Interface Bond and Fracture Failure Mechanism
por: Kim, Hoyeol, et al.
Publicado: (2017)

A Review on Metallic Alloys Fabrication Using Elemental Powder Blends by Laser Powder Directed Energy Deposition Process
por: Chen, Yitao, et al.
Publicado: (2020)

Synthesis of Ti-Al-xNb Ternary Alloys via Laser-Engineered Net Shaping for Biomedical Application: Densification, Electrochemical and Mechanical Properties Studies
por: Kanyane, Lehlogonolo Rudolf, et al.
Publicado: (2022)

Production and Characterization of Nanostructured Powders of Nd(2)Fe(14)B and Fe(90)Al(10) by Mechanical Alloying
por: Gómez Rodríguez, Alvaro Javier, et al.
Publicado: (2022)

Laser Powder Cladding of Ti-6Al-4V α/β Alloy
por: Al-Sayed Ali, Samar Reda, et al.
Publicado: (2017)

The Use of Selective Laser Melting to Increase the Performance of AlSi(9)Cu(3)Fe Alloy
por: Fousova, Michaela, et al.
Publicado: (2018)

Fabrication of Ti(3)Al-Based Intermetallic Alloy by Laser Powder Bed Fusion Using a Powder Mixture
por: Li, Kuanhe, et al.
Publicado: (2023)

Effect of Al Element on the Microstructure and Properties of Cu-Ni-Fe-Mn Alloys
por: Yang, Ran, et al.
Publicado: (2018)

Heat Treatment of NiTi Alloys Fabricated Using Laser Powder Bed Fusion (LPBF) from Elementally Blended Powders
por: Chmielewska, Agnieszka, et al.
Publicado: (2022)

The Influence of Powder Milling on Properties of SPS Compacted FeAl
por: Michalcová, Alena, et al.
Publicado: (2020)

Influence of Powder Characteristics on Processability of AlSi12 Alloy Fabricated by Selective Laser Melting
por: Baitimerov, Rustam, et al.
Publicado: (2018)

Wear Resistance Enhancement of Al6061 Alloy Surface Layer by Laser Dispersed Carbide Powders
por: Jendrzejewski, Rafał, et al.
Publicado: (2020)

Persistent Homology Analysis of the Microstructure of Laser-Powder-Bed-Fused Al–12Si Alloy
por: Suzuki, Asuka, et al.
Publicado: (2023)

Microstructure Evolution of FeNiCoCrAl(1.3)Mo(0.5) High Entropy Alloy during Powder Preparation, Laser Powder Bed Fusion, and Microplasma Spraying
por: Semikolenov, Anton, et al.
Publicado: (2021)

The Tribaloy T-800 Coatings Deposited by Laser Engineered Net Shaping (LENS(TM))
por: Durejko, Tomasz, et al.
Publicado: (2019)

Tailoring the Mechanical Properties of Laser Cladding-Deposited Ferrous Alloys with a Mixture of 410L Alloy and Fe–Cr–B–Si–Mo Alloy Powders
por: Huang, Sheng, et al.
Publicado: (2019)

Fatigue Behavior of Porous Ti-6Al-4V Made by Laser-Engineered Net Shaping
por: Razavi, Seyed Mohammad Javad, et al.
Publicado: (2018)

Evolution of the ε and γ phases in biodegradable Fe–Mn alloys produced using laser powder-bed fusion
por: Donik, Črtomir, et al.
Publicado: (2021)

Rapid Alloy Development of Extremely High-Alloyed Metals Using Powder Blends in Laser Powder Bed Fusion
por: Ewald, Simon, et al.
Publicado: (2019)

Comparative Quality Control of Titanium Alloy Ti–6Al–4V, 17–4 PH Stainless Steel, and Aluminum Alloy 4047 Either Manufactured or Repaired by Laser Engineered Net Shaping (LENS)
por: Eliaz, Noam, et al.
Publicado: (2020)

Tensile Fracture Behavior and Failure Mechanism of Additively-Manufactured AISI 4140 Low Alloy Steel by Laser Engineered Net Shaping
por: Kim, Hoyeol, et al.
Publicado: (2017)

Microstructural Evolution of AlCoCrFeNiSi High-Entropy Alloy Powder during Mechanical Alloying and Its Coating Performance
por: Tian, Lihui, et al.
Publicado: (2018)

Fabrication of Fe-Al Intermetallic Foams via Organic Compounds Assisted Sintering
por: Karczewski, Krzysztof, et al.
Publicado: (2015)

Magnetic Properties of the Soft Magnetic Composites Prepared Using Mixtures of Carbonyl Iron, FeSiCr, and FeSiAl Alloy Powders
por: Hsiang, Hsing-I, et al.
Publicado: (2023)

Cannot write session to /tmp/vufind_sessions/sess_ja2luumd6itmte63fi8hggh232