Cargando…

On the Assessment of Surface Quality and Productivity Aspects in Precision Hard Turning of AISI 4340 Steel Alloy: Relative Performance of Wiper vs. Conventional Inserts

This article reports an experimental assessment of surface quality generated in the precision turning of AISI 4340 steel alloy using conventional round and wiper nose inserts for different cutting conditions. A three-factor (each at 4 levels) full factorial design of experiment was followed for feed...

Descripción completa

Detalles Bibliográficos
Autores principales:	Abbas, Adel T., El Rayes, Magdy M., Luqman, Monis, Naeim, Noha, Hegab, Hussien, Elkaseer, Ahmed
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2020
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC7254342/ https://www.ncbi.nlm.nih.gov/pubmed/32349405 http://dx.doi.org/10.3390/ma13092036

Ejemplares similares

Comparative Evaluation of Surface Quality, Tool Wear, and Specific Cutting Energy for Wiper and Conventional Carbide Inserts in Hard Turning of AISI 4340 Alloy Steel
por: Abbas, Adel T., et al.
Publicado: (2020)

A Closer Look at Precision Hard Turning of AISI4340: Multi-Objective Optimization for Simultaneous Low Surface Roughness and High Productivity
por: Abbas, Adel T., et al.
Publicado: (2022)

Investigation on the Performance of Coated Carbide Tool during Dry Turning of AISI 4340 Alloy Steel
por: Wagri, Naresh Kumar, et al.
Publicado: (2023)

Towards Optimization of Machining Performance and Sustainability Aspects when Turning AISI 1045 Steel under Different Cooling and Lubrication Strategies
por: Abbas, Adel T., et al.
Publicado: (2019)

Dataset of manual metal arc welded heterogeneous thin steel plates AISI1018 AND AISI4340
por: Wanazusi, Titus, et al.
Publicado: (2023)

Effect of Selected Cooling and Deformation Parameters on the Structure and Properties of AISI 4340 Steel
por: Eckert, Maros, et al.
Publicado: (2020)

Cutting Performance Evaluation of the Coated Tools in High-Speed Milling of AISI 4340 Steel
por: Li, Yuan, et al.
Publicado: (2019)

Study on the Formation Mechanism of Cutting Dead Metal Zone for Turning AISI4340 with Different Chamfering Tools
por: Wu, Shujing, et al.
Publicado: (2022)

Analysis and Optimization of Machining Hardened Steel AISI 4140 with Self-Propelled Rotary Tools
por: Ahmed, Waleed, et al.
Publicado: (2021)

The Influence of Tool Rake Surface Geometry on the Hard Turning Process of AISI52100 Hardened Steel
por: Xu, Hanzhong, et al.
Publicado: (2019)

FEM-Based Study of Precision Hard Turning of Stainless Steel 316L
por: Elkaseer, Ahmed, et al.
Publicado: (2019)

Influence of Different Grades of CBN Inserts on Cutting Force and Surface Roughness of AISI H13 Die Tool Steel during Hard Turning Operation
por: Kumar, Pardeep, et al.
Publicado: (2019)

Effect of Different Cooling Strategies on Surface Quality and Power Consumption in Finishing End Milling of Stainless Steel 316
por: Abbas, Adel T., et al.
Publicado: (2021)

Experimental Investigation of Surface Roughness and Material Removal Rate in Wire EDM of Stainless Steel 304
por: Naeim, Noha, et al.
Publicado: (2023)

Wear Mechanism of Multilayer Coated Carbide Cutting Tool in the Milling Process of AISI 4340 under Cryogenic Environment
por: Muhamad, Shalina Sheik, et al.
Publicado: (2022)

Surface Topography Description after Turning Inconel 718 with a Conventional, Wiper and Special Insert Made by the SPS Technique
por: Szablewski, Piotr, et al.
Publicado: (2023)

Multi-Response Optimization in High-Speed Machining of Ti-6Al-4V Using TOPSIS-Fuzzy Integrated Approach
por: Abbas, Adel T., et al.
Publicado: (2020)

Tool Wear Effect on Surface Integrity in AISI 1045 Steel Dry Turning
por: Magalhães, Laurence Colares, et al.
Publicado: (2022)

Assessment of CVD- and PVD-Coated Carbides and PVD-Coated Cermet Inserts in the Optimization of Surface Roughness in Turning of AISI 1045 Steel
por: Paese, Evandro, et al.
Publicado: (2020)

Potatoes as Pen Wipers
Publicado: (1883)

Study for Performance Increase of a Extractor Device by Steel Replacement of AISI 304 Steel for AISI 420 Steel
por: Júnior, Francisco Alves de Lima, et al.
Publicado: (2021)

Effects of Multi-Pass Turning on Stress Corrosion Cracking of AISI 304 Austenitic Stainless Steel
por: Zhang, Yansong, et al.
Publicado: (2022)

Data-set collected during turning operation of AISI 1045 alloy steel with green cutting fluids in near dry condition
por: Dennison, Milon Selvam, et al.
Publicado: (2020)

In-situ Monitoring on Micro-hardness of Laser Molten Zone on AISI4140 Steel by Spectral Analysis
por: Wang, Siyu, et al.
Publicado: (2020)

Fundamental Investigation into Tool Wear and Surface Quality in High-Speed Machining of Ti6Al4V Alloy
por: Abbas, Adel T., et al.
Publicado: (2021)

Precision Hard Turning of Ti6Al4V Using Polycrystalline Diamond Inserts: Surface Quality, Cutting Temperature and Productivity in Conventional and High-Speed Machining
por: Abdelnasser, Elshaimaa, et al.
Publicado: (2020)

Statistical and Graphical Assessment of Circumferential and Radial Hardness Variation of AISI 4140, AISI 1020 and AA 6082 Aluminum Alloy
por: Al-Khalid, Hamad, et al.
Publicado: (2011)

Laser Dissimilar Welding of AISI 430F and AISI 304 Stainless Steels
por: Pańcikiewicz, Krzysztof, et al.
Publicado: (2020)

The Effect of Baking Heat Treatment on the Fatigue Strength and Life of Shot Peened 4340M Landing Gear Steel
por: Ahn, Seok-Hwan, et al.
Publicado: (2020)

Evaluating CNC Milling Performance for Machining AISI 316 Stainless Steel with Carbide Cutting Tool Insert
por: Equbal, Azhar, et al.
Publicado: (2022)

Influence of the Deep Cryogenic Treatment on AISI 52100 and AISI D3 Steel’s Corrosion Resistance
por: Jovičević-Klug, Patricia, et al.
Publicado: (2021)

Study of a Multicriterion Decision-Making Approach to the MQL Turning of AISI 304 Steel Using Hybrid Nanocutting Fluid
por: Dubey, Vineet, et al.
Publicado: (2021)

Topical rebamipide improves lid wiper epitheliopathy
por: Itakura, Hirotaka, et al.
Publicado: (2013)

Car Windshield Wiper in the Brain: Case Report
por: Liu, Zhenpeng, et al.
Publicado: (2016)

Structural and Micromechanical Properties of Nd:YAG Laser Marking Stainless Steel (AISI 304 and AISI 316)
por: Dywel, Piotr, et al.
Publicado: (2020)

Surface integrity optimization for ball-end hard milling of AISI D2 steel based on response surface methodology
por: Huang, Weimin, et al.
Publicado: (2023)

Corrosion Behavior of an AISI/SAE Steel Cut by Electropulsing
por: Montilla, Carlos Alberto, et al.
Publicado: (2019)

Evaluation of the Fatigue Behavior and Failure Mechanisms of 4340 Steel Coated with WIP-C1 (Ni/CrC) by Cold Spray
por: Goanță, Viorel, et al.
Publicado: (2022)

Influence of Technological Parameters on Chip Formation and Chip Control in Precision Hard Turning of Ti-6Al-4V
por: Abdelnasser, Elshaimaa, et al.
Publicado: (2023)

Corrosion Resistance of AISI 442 and AISI 446 Ferritic Stainless Steels as a Support for PEMWE Bipolar Plates
por: Dan, Mircea Laurentiu, et al.
Publicado: (2023)

Cannot write session to /tmp/vufind_sessions/sess_gtp4sjk1pa1ugcd20jpn0tbfaf