Cargando…

Molding Binder Influence on the Porosity and Gas Permeability of Ceramic Casting Molds

The investment casting process is widely used in the aerospace industry to produce complex engine parts. The article determines the properties of quartz powders, nanosilica dioxide binders, and multilayer samples of ceramic casting molds. The properties of spherical molds obtained using an alcohol-w...

Descripción completa

Detalles Bibliográficos
Autores principales:	Wisniewski, Pawel, Sitek, Ryszard, Towarek, Aleksandra, Choinska, Emilia, Moszczynska, Dorota, Mizera, Jaroslaw
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2020
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC7345566/ https://www.ncbi.nlm.nih.gov/pubmed/32560239 http://dx.doi.org/10.3390/ma13122735

Ejemplares similares

Investigations of Model Multilayer Ceramic Casting Molds in a Raw State by Nondestructive Methods
por: Żaba, Krzysztof, et al.
Publicado: (2021)

Cast Iron Parts Obtained in Ceramic Molds Produced by Binder Jetting 3D Printing—Morphological and Mechanical Characterization
por: Păcurar, Răzvan, et al.
Publicado: (2021)

Comparison of the Properties of Alkali-Phenolic Binder in Terms of Selection of Molding Sand for Steel Castings
por: Łucarz, Mariusz, et al.
Publicado: (2019)

Sensor Fusion for Simultaneous Estimation of In-Plane Permeability and Porosity of Fiber Reinforcement in Resin Transfer Molding
por: Qi, Wei, et al.
Publicado: (2022)

Porosity Reducing Processing Stages of Additive Manufactured Molding (AMM) for Closed-Mold Composite Fabrication
por: Pollard, Marquese, et al.
Publicado: (2020)

Polymer Binders of Ceramic Nanoparticles for Precision Casting of Nickel-Based Superalloys
por: Wiśniewski, Paweł
Publicado: (2021)

Effect of Increased Powder–Binder Adhesion by Backbone Grafting on the Properties of Feedstocks for Ceramic Injection Molding
por: Ghasemi-Mobarakeh, Laleh, et al.
Publicado: (2022)

Influence of Weather Conditions and Mechanical Reclamation on Molding Sand with Alkali-Phenolic Binder for Manganese Cast Steel
por: Łucarz, Mariusz, et al.
Publicado: (2022)

Model-Assisted Control of Flow Front in Resin Transfer Molding Based on Real-Time Estimation of Permeability/Porosity Ratio
por: Wei, Bai-Jian, et al.
Publicado: (2016)

Binders Used for the Manufacturing of Composite Materials by Liquid Composite Molding
por: Terekhov, Ivan V., et al.
Publicado: (2021)

The Use of Barley Malt as a Binder in Molding Sand Technology
por: Samociuk, Bartłomiej, et al.
Publicado: (2022)

Modeling and Simulation of the Casting Process with Skeletal Sand Mold
por: Kang, Jinwu, et al.
Publicado: (2020)

Influence of Mineralogical Structure of Mold Flux Film on Heat Transfer in Mold during Continuous Casting of Peritectic Steel
por: Liu, Lei, et al.
Publicado: (2022)

Reducing the Burn Marks on Injection-Molded Parts by External Gas-Assisted Injection Molding
por: Li, Jiquan, et al.
Publicado: (2021)

Fluid Flow in Continuous Casting Mold for Ultra-Wide Slab
por: Li, Gang, et al.
Publicado: (2023)

Influence of Gating System Parameters of Die-Cast Molds on Properties of Al-Si Castings
por: Gašpár, Štefan, et al.
Publicado: (2021)

Graphite Compactness Degree and Nodularity of High-Si Ductile Iron Produced via Permanent Mold versus Sand Mold Casting
por: Anca, Denisa-Elena, et al.
Publicado: (2022)

Influence of Heat Sink on the Mold Temperature of Gypsum Mold Used in Injection Molding
por: Lin, Chung-Chih, et al.
Publicado: (2020)

The Impact of Plastic Deformation on the Microstructure and Tensile Strength of Haynes 282 Nickel Superalloy Produced by DMLS and Casting
por: Sitek, Ryszard, et al.
Publicado: (2022)

Dimensional Accuracy of Stone Casts Obtained with Multiple Pours into the Same Mold
por: Valente, Valdimar da Silva, et al.
Publicado: (2012)

Viscosity estimation model of fluorine-containing mold flux for continuous casting
por: Zhao, Zhongyu, et al.
Publicado: (2021)

External Gas-Assisted Mold Temperature Control Improves Weld Line Quality in the Injection Molding Process
por: The Uyen, Tran Minh, et al.
Publicado: (2020)

Three-Dimensional-Printed Molds from Water-Soluble Sulfate Ceramics for Biocomposite Formation through Low-Pressure Injection Molding
por: Golubchikov, Daniil, et al.
Publicado: (2023)

Effect of mold treatment by solvent on PDMS molding into nanoholes
por: Con, Celal, et al.
Publicado: (2013)

Enhanced Injection Molding Simulation of Advanced Injection Molds
por: Zink, Béla, et al.
Publicado: (2017)

Focused molding using adhesive pads in Mehta casting for early-onset scoliosis
por: Abraham, Roby, et al.
Publicado: (2014)

Structural and compositional analysis of a casting mold sherd from ancient China
por: Zong, Yunbing, et al.
Publicado: (2017)

First Evidence of “Earth Wax” Inside the Casting Molds from the Roman Era
por: Jagošová, Klára, et al.
Publicado: (2021)

Modeling of Interfacial Tension and Inclusion Motion Behavior in Steelmaking Continuous Casting Mold
por: Siddiqui, Md Irfanul Haque, et al.
Publicado: (2023)

Study on External Gas-Assisted Mold Temperature Control with the Assistance of a Flow Focusing Device in the Injection Molding Process
por: Giang, Nguyen Truong, et al.
Publicado: (2021)

Molds and the lungs
por: Sharma, Bharat Bhushan
Publicado: (2010)

Molded Optics
por: Schaub, Michael, et al.
Publicado: (2016)

An Analysis of the Casting Polymer Mold Wear Manufactured Using PolyJet Method Based on the Measurement of the Surface Topography
por: Turek, Paweł, et al.
Publicado: (2020)

In-Mold Sensors for Injection Molding: On the Way to Industry 4.0
por: Ageyeva, Tatyana, et al.
Publicado: (2019)

Multiple In-Mold Sensors for Quality and Process Control in Injection Molding
por: Párizs, Richárd Dominik, et al.
Publicado: (2023)

Gas Permeability of Mold during Freezing Process Alters the Pore Distribution of Gelatin Sponge and Its Bone-Forming Ability
por: Han, Xiaoyu, et al.
Publicado: (2020)

Effect of Free Cross-Linking Rate on the Molding of Bulk SiOC Ceramics
por: Zheng, Lei, et al.
Publicado: (2023)

The Design of 3D-Printed Lattice-Reinforced Thickness-Varying Shell Molds for Castings
por: Shangguan, Haolong, et al.
Publicado: (2018)

Optimization on Reducing Slag Entrapment in 150 × 1270 mm Slab Continuous Casting Mold
por: Wang, Yang, et al.
Publicado: (2019)

Effect of the Biodegradable Component Addition to the Molding Sand on the Microstructure and Properties of Ductile Iron Castings
por: Major-Gabryś, Katarzyna, et al.
Publicado: (2022)

Cannot write session to /tmp/vufind_sessions/sess_f3ggilco05p97cqklp2cm9merr