Cargando…

Design and Fabrication of New High Entropy Alloys for Evaluating Titanium Replacements in Additive Manufacturing

High entropy alloys (HEAs) were prepared using the powder bed fusion (PBF) technique. Among titanium free alloys AlCoCrFeNiMn, CoCr(1.3)FeMnNi(0.7), AlCoCrFeNi(1.3), and AlCoCr(1.3)FeNi(1.3) have been further investigated. A cost comparison was done for these four alloys as well as the titanium-base...

Descripción completa

Detalles Bibliográficos
Autores principales:	Sarswat, Prashant, Smith, Taylor, Sarkar, Sayan, Murali, Arun, Free, Michael
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2020
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC7372361/ https://www.ncbi.nlm.nih.gov/pubmed/32640563 http://dx.doi.org/10.3390/ma13133001

Ejemplares similares

Designing against phase and property heterogeneities in additively manufactured titanium alloys
por: Zhang, Jingqi, et al.
Publicado: (2022)

Additive Manufacturing of High-Entropy Alloys: A Review
por: Chen, Shuying, et al.
Publicado: (2018)

Dynamic Mechanical Properties of TC11 Titanium Alloys Fabricated by Wire Arc Additive Manufacturing
por: Tian, Ze, et al.
Publicado: (2022)

Additive manufacturing of titanium alloys: state of the art, challenges and opportunities
por: Dutta, Bhaskar, et al.
Publicado: (2016)

Strong and ductile titanium–oxygen–iron alloys by additive manufacturing
por: Song, Tingting, et al.
Publicado: (2023)

Hybridized Tungsten Oxide Nanostructures for Food Quality Assessment: Fabrication and Performance Evaluation
por: Kumar, Pankaj, et al.
Publicado: (2018)

Synergistic effect of band convergence and carrier transport on enhancing the thermoelectric performance of Ga doped Cu(2)Te at medium temperatures
por: Sarkar, Sayan, et al.
Publicado: (2019)

Additive Manufacturing Technologies of High Entropy Alloys (HEA): Review and Prospects
por: Ron, Tomer, et al.
Publicado: (2023)

Perspectives on Additive Manufacturing Enabled Beta-Titanium Alloys for Biomedical Applications
por: Sing, Swee Leong
Publicado: (2022)

Microstructure Evaluation of the Potential of Additive Manufactured Dissimilar Titanium–Aluminum Alloys
por: Nagamatsu, Hideaki, et al.
Publicado: (2022)

Complementary Methods for the Assessment of the Porosity of Laser Additive-Manufactured Titanium Alloy
por: Petrișor, Silviu Mihai, et al.
Publicado: (2023)

Programming Crystallographic Orientation in Additive‐Manufactured Beta‐Type Titanium Alloy
por: Luo, Xuan, et al.
Publicado: (2023)

Additive Manufacturing: Alloy Design and Process Innovations
por: Prashanth, Konda Gokuldoss, et al.
Publicado: (2020)

Effect of Energy Input on Microstructure and Mechanical Properties of Titanium Aluminide Alloy Fabricated by the Additive Manufacturing Process of Electron Beam Melting
por: Mohammad, Ashfaq, et al.
Publicado: (2017)

Phase Studies of Additively Manufactured Near Beta Titanium Alloy-Ti55511
por: Maimaitiyili, Tuerdi, et al.
Publicado: (2020)

Research Status and Prospect of Additive Manufactured Nickel-Titanium Shape Memory Alloys
por: Wen, Shifeng, et al.
Publicado: (2021)

The influence of tool quality on the machining of additive manufactured and powder metallurgy titanium alloys
por: Ma, Junhui, et al.
Publicado: (2022)

Underlying factors determining grain morphologies in high-strength titanium alloys processed by additive manufacturing
por: Nartu, Mohan S. K. K. Y., et al.
Publicado: (2023)

A Review: Design from Beta Titanium Alloys to Medium-Entropy Alloys for Biomedical Applications
por: Wong, Ka-Kin, et al.
Publicado: (2023)

Thermodynamics-guided alloy and process design for additive manufacturing
por: Sun, Zhongji, et al.
Publicado: (2022)

Impact of grain orientation and phase on Volta potential differences in an additively manufactured titanium alloy
por: Benzing, Jake T., et al.
Publicado: (2021)

Additive manufacturing of titanium-based alloys- A review of methods, properties, challenges, and prospects
por: Tshephe, Thato Sharon, et al.
Publicado: (2022)

Antibacterial performance of a porous Cu-bearing titanium alloy by laser additive manufacturing
por: Xu, Jiawei, et al.
Publicado: (2023)

Printability of alloys for additive manufacturing
por: Mukherjee, T., et al.
Publicado: (2016)

The Hardness of Additively Manufactured Alloys
por: Zuback, J.S., et al.
Publicado: (2018)

Additive manufacturing of magnesium alloys
por: Karunakaran, Rakeshkumar, et al.
Publicado: (2020)

Additive Manufacturing of Alloys and Composites
por: Dong, Haokai, et al.
Publicado: (2023)

The Effects of Post Heat Treatment on the Microstructural and Mechanical Properties of an Additive-Manufactured Porous Titanium Alloy
por: Yu, Guisheng, et al.
Publicado: (2020)

The State of the Art in Machining Additively Manufactured Titanium Alloy Ti-6Al-4V
por: Zhang, Chen, et al.
Publicado: (2023)

In Situ Tensile Observation of the Effect of Annealing on Fracture Behavior of Laser Additive Manufactured Titanium Alloy
por: Xu, Ming, et al.
Publicado: (2023)

Compositional Effects of Additively Manufactured Refractory High-Entropy Alloys under High-Energy Helium Irradiation
por: Lang, Eric, et al.
Publicado: (2022)

Design and Fabrication of an Additively Manufactured Aluminum Mirror with Compound Surfaces
por: Zhang, Jizhen, et al.
Publicado: (2022)

Programming Crystallographic Orientation in Additive‐Manufactured Beta‐Type Titanium Alloy (Adv. Sci. 28/2023)
por: Luo, Xuan, et al.
Publicado: (2023)

Fatigue database of additively manufactured alloys
por: Zhang, Zian, et al.
Publicado: (2023)

Alloy Design and Fabrication of Duplex Titanium-Based Alloys by Spark Plasma Sintering for Biomedical Implant Applications
por: Ijaz, Muhammad Farzik, et al.
Publicado: (2022)

Structure and Mechanical Properties of Cu–Al–Mn Alloys Fabricated by Electron Beam Additive Manufacturing
por: Moskvichev, Evgeny, et al.
Publicado: (2022)

Data related to the sinter structure analysis of titanium structures fabricated via binder jetting additive manufacturing
por: Wheat, Evan, et al.
Publicado: (2018)

Microstructure and Mechanical Properties of Wire Arc Additively Manufactured MoNbTaWTi High Entropy Alloys
por: Liu, Jian, et al.
Publicado: (2021)

Strengthening Mechanisms in CoCrFeNiX(0.4) (Al, Nb, Ta) High Entropy Alloys Fabricated by Powder Plasma Arc Additive Manufacturing
por: Zhang, Yupeng, et al.
Publicado: (2021)

Additively manufactured unimorph dielectric elastomer actuators: Design, materials, and fabrication
por: Sikulskyi, Stanislav, et al.
Publicado: (2022)

Cannot write session to /tmp/vufind_sessions/sess_98hlr1d7jiunn086432mq7lifo