Cargando…

Effects of Scanning Strategy and Printing Temperature on the Compressive Behaviors of 3D Printed Polyamide-Based Composites

In this work, the effects of scanning strategies and printing temperature on mechanical properties and crush behaviors of columns manufactured using the fused deposition modeling (FDM) technique were studied. The results showed that scanning strategy and printing temperature had significant influenc...

Descripción completa

Detalles Bibliográficos
Autores principales:	Wang, Jin, Xiang, Jiangyang, Lin, Hao, Wang, Kui, Yao, Song, Peng, Yong, Rao, Yanni
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2020
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC7466108/ https://www.ncbi.nlm.nih.gov/pubmed/32784976 http://dx.doi.org/10.3390/polym12081783

Ejemplares similares

Flexure Behaviors of ABS-Based Composites Containing Carbon and Kevlar Fibers by Material Extrusion 3D Printing
por: Wang, Kui, et al.
Publicado: (2019)

Effect of Additives and Print Orientation on the Properties of Laser Sintering-Printed Polyamide 12 Components
por: Zárybnická, Lucie, et al.
Publicado: (2022)

Effect of Manufacture-Induced Interfaces on the Tensile Properties of 3D Printed Polyamide and Short Carbon Fibre-Reinforced Polyamide Composites
por: Hou, Yingwei, et al.
Publicado: (2023)

Mechanical Analysis of 3D Printed Polyamide Composites under Different Filler Loadings
por: Mohd Radzuan, Nabilah Afiqah, et al.
Publicado: (2023)

Tension and Compression Properties of 3D-Printed Composites: Print Orientation and Strain Rate Effects
por: Fisher, Tom, et al.
Publicado: (2023)

Influence of the Type of Plastic and Printing Technologies on the Compressive Behavior of 3D-Printed Heel Prototypes
por: Gelaziene, Edita, et al.
Publicado: (2023)

Compression Behavior of EBM Printed Auxetic Chiral Structures
por: Gunaydin, Kadir, et al.
Publicado: (2022)

Experimental Investigation of Compression Properties of Composites with Printed Braiding Structure
por: Li, Zhengning, et al.
Publicado: (2018)

Mechanical and Tribological Properties of 3D Printed Polyamide 12 and SiC/PA12 Composite by Selective Laser Sintering
por: Yu, Guoyan, et al.
Publicado: (2022)

Effect of carbon fiber reinforcement on dimensional variations of 3D printed polyamide-6 composites: A simulation study
por: AL RASHID, Ans, et al.
Publicado: (2022)

Effects of Printing Temperature and Filling Percentage on the Mechanical Behavior of Fused Deposition Molding Technology Components for 3D Printing
por: Hsueh, Ming-Hsien, et al.
Publicado: (2021)

Document image processing for scanning and printing
por: Safonov, Ilia V, et al.
Publicado: (2019)

3D Printing of PLA/clay Nanocomposites: Influence of Printing Temperature on Printed Samples Properties
por: Coppola, Bartolomeo, et al.
Publicado: (2018)

Piezoelectric inkjet printing of tyrosinase (polyphenol oxidase) enzyme on atmospheric plasma treated polyamide fabric
por: Biswas, Tuser T., et al.
Publicado: (2022)

Digital Sublimation Printing on Knitted Polyamide 6.6 Fabric Treated with Non-Thermal Plasma
por: Silva, Marcia Cristina, et al.
Publicado: (2021)

Tribological Behavior of 3D-Printed Nanometer SiC and SiO(2) Particle-Reinforced Polyamide 12 Composites by Selective Laser Sintering under Seawater Lubrication Condition
por: Ma, Jingdong, et al.
Publicado: (2022)

Investigation on the Temperature Control Accuracy of a Print Head for Extrusion 3D Printing and Its Improved Design
por: Zhang, Peng, et al.
Publicado: (2022)

Mechanical Behavior of Printed Strain Hardening Cementitious Composites
por: Chaves Figueiredo, Stefan, et al.
Publicado: (2020)

A Numerical Study on 3D Printed Cementitious Composites Mixes Subjected to Axial Compression
por: Liu, Hanqiu, et al.
Publicado: (2021)

Inkjet printing of energetic composites with high density
por: Xu, Chuanhao, et al.
Publicado: (2018)

3D Printed porous polyamide macrocapsule combined with alginate microcapsules for safer cell-based therapies
por: Saenz del Burgo, Laura, et al.
Publicado: (2018)

Polyamide 12 Materials Study of Morpho-Structural Changes during Laser Sintering of 3D Printing
por: Simha Martynková, Gražyna, et al.
Publicado: (2021)

Compression Performance and Deformation Behavior of 3D-Printed PLA-Based Lattice Structures
por: Qin, Dongxue, et al.
Publicado: (2022)

High-Temperature Shape Memory Behavior of Semicrystalline Polyamide Thermosets
por: Li, Ming, et al.
Publicado: (2018)

A Printing Strategy for Embedding Conductor Paths into FFF Printed Parts
por: Banko, Timo, et al.
Publicado: (2023)

Robust PDF Watermarking against Print–Scan Attack
por: Li, Lei, et al.
Publicado: (2023)

Multimaterial Embedded 3D Printing of Composite Reinforced Soft Actuators
por: Wang, Zhenhua, et al.
Publicado: (2023)

Polyamide Noncoated Device for Adsorption-Based Microextraction and Novel 3D Printed Thin-Film Microextraction Supports
por: Kołodziej, Dominika, et al.
Publicado: (2022)

Medical-Grade Polyamide 12 Nanocomposite Materials for Enhanced Mechanical and Antibacterial Performance in 3D Printing Applications
por: Vidakis, Nectarios, et al.
Publicado: (2022)

A Comprehensive Investigation on 3D Printing of Polyamide 11 and Thermoplastic Polyurethane via Multi Jet Fusion
por: Tey, Wei Shian, et al.
Publicado: (2021)

Investigation on the Temperature Distribution Uniformity of an Extrusion-Based 3D Print Head and Its Temperature Control Strategy
por: Gao, Qiang, et al.
Publicado: (2022)

Effect of Temperature on the Mechanical Properties and Polymerization Kinetics of Polyamide-6 Composites
por: Li, Mei-Xian, et al.
Publicado: (2020)

The Effect of Nozzle Temperature on the Low-Temperature Printing Performance of Low-Viscosity Food Ink
por: Tong, Qiang, et al.
Publicado: (2023)

Influence of Geometric and Manufacturing Parameters on the Compressive Behavior of 3D Printed Polymer Lattice Structures
por: Guerra Silva, Rafael, et al.
Publicado: (2021)

Slicing Algorithm and Partition Scanning Strategy for 3D Printing Based on GPU Parallel Computing
por: Lai, Xuhui, et al.
Publicado: (2021)

Dielectric Behavior of Thin Polymerized Composite Layers Fabricated by Inkjet-Printing
por: Reinheimer, Timo, et al.
Publicado: (2023)

Analysis of the Influencing Factors of FDM-Supported Positions for the Compressive Strength of Printing Components
por: Feng, Zhengkai, et al.
Publicado: (2021)

Quasi-Static Multifunctional Characterization of 3D-Printed Carbon Fiber Composites for Compressive-Electrical Properties
por: Ghimire, Ritesh, et al.
Publicado: (2022)

3D Printing Processability of a Thermally Conductive Compound Based on Carbon Nanofiller-Modified Thermoplastic Polyamide 12
por: Zhang, Zhenxue, et al.
Publicado: (2022)

3D-Printed Polyamide 12/Styrene–Acrylic Copolymer–Boron Nitride (PA12/SA–BN) Composite with Macro and Micro Double Anisotropic Thermally Conductive Structures
por: Chen, Minhang, et al.
Publicado: (2023)

Cannot write session to /tmp/vufind_sessions/sess_fj8dup9apq4glfvq5bbcljrcp3