Cargando…

Evolution of SLA-Based Al(2)O(3) Microstructure During Additive Manufacturing Process

Evolution of additively manufactured (AM) ceramics’ microstructure between manufacturing stages is a hardly explored topic. These data are of high demand for advanced numerical modeling. In this work, 3D microstructural models of Al(2)O(3) greenbody, brownbody and sintered material are presented and...

Descripción completa

Detalles Bibliográficos
Autores principales:	Chugunov, Svyatoslav, Adams, Nikolaus A., Akhatov, Iskander
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2020
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC7557533/ https://www.ncbi.nlm.nih.gov/pubmed/32899496 http://dx.doi.org/10.3390/ma13183928

Ejemplares similares

The Fabrication and Characterization of BaTiO(3) Piezoceramics Using SLA 3D Printing at 465 nm Wavelength
por: Smirnov, Andrey, et al.
Publicado: (2022)

Towards Creation of Ceramic-Based Low Permeability Reference Standards
por: Chugunov, Svyatoslav, et al.
Publicado: (2019)

Experimental Characterization Framework for SLA Additive Manufacturing Materials
por: Martín-Montal, Jordi, et al.
Publicado: (2021)

Evaluation of Mechanical Properties and Filler Interaction in the Field of SLA Polymeric Additive Manufacturing
por: Jirků, Petr, et al.
Publicado: (2023)

Very High Cycle Fatigue Behavior of Additively Manufactured 316L Stainless Steel
por: Voloskov, Boris, et al.
Publicado: (2020)

Microstructure and properties of additively manufactured Al–Ce–Mg alloys
por: Sisco, K., et al.
Publicado: (2021)

Mechanical Anisotropy and Surface Roughness in Additively Manufactured Parts Fabricated by Stereolithography (SLA) Using Statistical Analysis
por: Aravind Shanmugasundaram, Sunil, et al.
Publicado: (2020)

Anisotropy of Mechanical Properties and Residual Stress in Additively Manufactured 316L Specimens
por: Fedorenko, Alexey, et al.
Publicado: (2021)

Restirring and Reheating Effects on Microstructural Evolution of Al–Zn–Mg–Cu Alloy during Underwater Friction Stir Additive Manufacturing
por: Li, Ying, et al.
Publicado: (2022)

Microstructures and Mechanical Properties of Hybrid, Additively Manufactured Ti(6)Al(4)V after Thermomechanical Processing
por: Hemes, Susanne, et al.
Publicado: (2021)

Tailoring Microstructure and Mechanical Properties of Additively-Manufactured Ti6Al4V Using Post Processing
por: Ganor, Yaron Itay, et al.
Publicado: (2021)

Microstructure Evolution, Mechanical Properties and Deformation Behavior of an Additively Manufactured Maraging Steel
por: Chadha, Kanwal, et al.
Publicado: (2020)

Temperature and Microstructure Evolution in Gas Tungsten Arc Welding Wire Feed Additive Manufacturing of Ti-6Al-4V
por: Charles Murgau, Corinne, et al.
Publicado: (2019)

Additive manufacturing of alloys with programmable microstructure and properties
por: Gao, Shubo, et al.
Publicado: (2023)

Microstructure Evolution and Mechanical Properties of a Wire-Arc Additive Manufactured Austenitic Stainless Steel: Effect of Processing Parameter
por: Long, Ping, et al.
Publicado: (2021)

The Microstructure Evolution of a Fe(3)Al Alloy during the LENS Process
por: Karczewski, Krzysztof, et al.
Publicado: (2018)

Study on Microstructural and Mechanical Properties of an Al–Cu–Sn Alloy Wall Deposited by Double-Wire Arc Additive Manufacturing Process
por: Wang, Shuai, et al.
Publicado: (2019)

Micromechanical Modeling of AlSi10Mg Processed by Laser-Based Additive Manufacturing: From as-Built to Heat-Treated Microstructures
por: Nammalvar Raja Rajan, Aravindh, et al.
Publicado: (2022)

Evolution of solidification texture during additive manufacturing
por: Wei, H. L., et al.
Publicado: (2015)

Microstructural Evolution and Hardness Responses of 7050 Al Alloy during Processing
por: Zhou, Yuting, et al.
Publicado: (2022)

The Effect of Cu Content on the Microstructure and Properties of the Wire Arc Additive Manufacturing Al-Cu Alloy
por: Ren, Lingling, et al.
Publicado: (2023)

EMI-EGI SLA
por: Di Meglio, A, et al.
Publicado: (2011)

Investigation on Flaw Evolution of Additively Manufactured Al(2)O(3) Ceramic by In Situ X-ray Computed Tomography
por: Cai, Naijia, et al.
Publicado: (2022)

Thermographic Microstructure Monitoring in Electron Beam Additive Manufacturing
por: Raplee, J., et al.
Publicado: (2017)

Solute trapping and non-equilibrium microstructure during rapid solidification of additive manufacturing
por: Ren, Neng, et al.
Publicado: (2023)

Densification, Microstructure, and Mechanical Properties of Additively Manufactured 2124 Al–Cu Alloy by Selective Laser Melting
por: Deng, Junwang, et al.
Publicado: (2020)

Optimization of Dimensional Accuracy and Surface Roughness of SLA Patterns and SLA-Based IC Components
por: Mukhangaliyeva, Aishabibi, et al.
Publicado: (2023)

Additive manufacturing of Al(2)O(3) ceramics with MgO/SiC contents by laser powder bed fusion process
por: Ur Rehman, Asif, et al.
Publicado: (2023)

Microstructure Evolution of Al6061 Alloy Made by Additive Friction Stir Deposition
por: Zeng, Congyuan, et al.
Publicado: (2022)

Microstructure Evolution and Mechanical Properties of Al–Cu–Mg Alloys with Si Addition
por: Shah, Abdul Wahid, et al.
Publicado: (2023)

Aluminum Parts Fabricated by Laser-Foil-Printing Additive Manufacturing: Processing, Microstructure, and Mechanical Properties
por: Hung, Chia-Hung, et al.
Publicado: (2020)

SLA research and language teaching /
por: Ellis, Rod
Publicado: (1997)

Parametric Modeling of Biomimetic Cortical Bone Microstructure for Additive Manufacturing
por: Robles-Linares, José A., et al.
Publicado: (2019)

Design of Kinematic Connectors for Microstructured Materials Produced by Additive Manufacturing
por: Silva, Miguel R., et al.
Publicado: (2021)

Effect of Mg Content on Microstructure and Properties of Al–Mg Alloy Produced by the Wire Arc Additive Manufacturing Method
por: Ren, Lingling, et al.
Publicado: (2019)

Turning of Additively Manufactured Ti6Al4V: Effect of the Highly Oriented Microstructure on the Surface Integrity
por: Lizzul, Lucia, et al.
Publicado: (2021)

Corrigendum: Additive manufacturing of Al(2)O(3) ceramics with MgO/SiC contents by laser powder bed fusion process
por: Ur Rehman, Asif, et al.
Publicado: (2023)

Subsurface Cooling Rates and Microstructural Response during Laser Based Metal Additive Manufacturing
por: Thampy, Vivek, et al.
Publicado: (2020)

Microstructures and Phases in Electron Beam Additively Manufactured Ti-Al-Mo-Zr-V/CuAl9Mn2 Alloy
por: Zykova, Anna, et al.
Publicado: (2023)

Solid-State Cold Spray Additive Manufacturing of Ni-Based Superalloys: Processing–Microstructure–Property Relationships
por: Ralls, Alessandro M., et al.
Publicado: (2023)

Cannot write session to /tmp/vufind_sessions/sess_r40qcm6iah79eupg2t45upeeog