Cargando…

A Novel γ′-Strengthened Nickel-Based Superalloy for Laser Powder Bed Fusion

An experimental printable γ′-strengthened nickel-based superalloy, MAD542, is proposed. By process optimization, a crack-free component with less than 0.06% defect was achieved by laser powder bed fusion (LPBF). After post-processing by solution heat treatment, a recrystallized structure was reveale...

Descripción completa

Detalles Bibliográficos
Autores principales:	Xu, Jinghao, Gruber, Hans, Lin Peng, Ru, Moverare, Johan
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2020
Materias:	Communication
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC7662829/ https://www.ncbi.nlm.nih.gov/pubmed/33147831 http://dx.doi.org/10.3390/ma13214930

Ejemplares similares

Fabrication of Crack-Free Nickel-Based Superalloy Considered Non-Weldable during Laser Powder Bed Fusion
por: Sanchez-Mata, Oscar, et al.
Publicado: (2018)

Cyclic Deformation Behavior of Additive-Manufactured IN738LC Superalloys from Virgin and Reused Powders
por: Chen, Jialiang, et al.
Publicado: (2022)

Influence of Laser Powder Bed Fusion Process Parameters on Voids, Cracks, and Microhardness of Nickel-Based Superalloy Alloy 247LC
por: Adegoke, Olutayo, et al.
Publicado: (2020)

On the Microstructure of Laser Beam Powder Bed Fusion Alloy 718 and Its Influence on the Low Cycle Fatigue Behaviour
por: Balachandramurthi, Arun Ramanathan, et al.
Publicado: (2020)

Nanoparticle Tracing during Laser Powder Bed Fusion of Oxide Dispersion Strengthened Steels
por: Yang, Yangyiwei, et al.
Publicado: (2021)

Powder Interlayer Bonding of Nickel-Based Superalloys with Dissimilar Chemistries
por: Stanners, Olivia, et al.
Publicado: (2021)

Electron Backscattered Diffraction to Estimate Residual Stress Levels of a Superalloy Produced by Laser Powder Bed Fusion and Subsequent Heat Treatments
por: Terner, Mathieu, et al.
Publicado: (2020)

Laser Powder Bed Fusion of Metal Coated Copper Powders
por: Lindström, Viktor, et al.
Publicado: (2020)

The Effect of Processing Variables on Powder Interlayer Bonding in Nickel-Based Superalloys
por: Stanners, Olivia, et al.
Publicado: (2020)

Laser Powder Bed Fusion of Chromium Bronze Using Recycled Powder
por: Pelevin, Ivan A., et al.
Publicado: (2021)

Material Evaluation and Dynamic Powder Deposition Modeling of PEEK/CF Composite for Laser Powder Bed Fusion Process
por: Li, Jiang, et al.
Publicado: (2023)

An Approach to the Uniform Dispersion of Graphene Nanosheets in Powder Metallurgy Nickel-Based Superalloy
por: Gao, Yu-Xi, et al.
Publicado: (2019)

Evaluation of Inconel 718 Metallic Powder to Optimize the Reuse of Powder and to Improve the Performance and Sustainability of the Laser Powder Bed Fusion (LPBF) Process
por: Gruber, Konrad, et al.
Publicado: (2021)

Laser Cladding of Ultra-Thin Nickel-Based Superalloy Sheets
por: Gabriel, Tobias, et al.
Publicado: (2017)

Gas Atomization of Duplex Stainless Steel Powder for Laser Powder Bed Fusion
por: Cui, Chengsong, et al.
Publicado: (2023)

Approach to Estimate the Phase Formation and the Mechanical Properties of Alloys Processed by Laser Powder Bed Fusion via Casting
por: Kühn, Uta, et al.
Publicado: (2022)

Impact of Atomization Pressure on the Particle Size of Nickel-Based Superalloy Powders by Numerical Simulation
por: Qing, Yongquan, et al.
Publicado: (2022)

Low-Power Laser Powder Bed Fusion Processing of Scalmalloy(®)
por: Martucci, Alessandra, et al.
Publicado: (2022)

Crystallographic Orientation Influence on the Serrated Yielding Behavior of a Single-Crystal Superalloy
por: Segersäll, Mikael, et al.
Publicado: (2013)

Evolution of the ε and γ phases in biodegradable Fe–Mn alloys produced using laser powder-bed fusion
por: Donik, Črtomir, et al.
Publicado: (2021)

Study on laser powder bed fusion of nickel-base alloy of G-surface structure: scanning strategy, properties and compression properties
por: Qian, Bo, et al.
Publicado: (2021)

The Influence of Process Parameters and Build Orientation on the Creep Behaviour of a Laser Powder Bed Fused Ni-based Superalloy for Aerospace Applications
por: Hilal, Hani, et al.
Publicado: (2019)

Mechanical Properties of Titanium/Nano-Fluorapatite Parts Produced by Laser Powder Bed Fusion
por: Wu, Po-Kuan, et al.
Publicado: (2023)

Investigation on Sub-Solvus Recrystallization Mechanisms in an Advanced γ-γ’ Nickel-Based Superalloy GH4151
por: Lv, Shaomin, et al.
Publicado: (2020)

Grain Refinement of a Powder Nickel-Base Superalloy Using Hot Deformation and Slow-Cooling
por: Fan, Xianqiang, et al.
Publicado: (2018)

Investigating the Recyclability of Laser PP CP 75 Polypropylene Powder in Laser Powder Bed Fusion (L-PBF)
por: Mwania, Fredrick M., et al.
Publicado: (2022)

The role of side-branching in microstructure development in laser powder-bed fusion
por: Pham, Minh-Son, et al.
Publicado: (2020)

An Empirical Approach for the Development of Process Parameters for Laser Powder Bed Fusion
por: Pfaff, Aron, et al.
Publicado: (2020)

Laser Powder Bed Fusion of Polymers: Quantitative Research Direction Indices
por: Kusoglu, Ihsan Murat, et al.
Publicado: (2021)

Laser Powder Bed Fusion of Dissimilar Metal Materials: A Review
por: Guan, Jieren, et al.
Publicado: (2023)

Micro-Twinning in IN738LC Manufactured with Laser Powder Bed Fusion
por: Megahed, Sandra, et al.
Publicado: (2023)

Spreadability of Metal Powders for Laser-Powder Bed Fusion via Simple Image Processing Steps
por: Vakifahmetoglu, Cekdar, et al.
Publicado: (2021)

On the Use of Metal Sinter Powder in Laser Powder Bed Fusion Processing (PBF-LB/M)
por: Bernsmann, Jan-Simeon Ludger, et al.
Publicado: (2023)

Powder Surface Roughness as Proxy for Bed Density in Powder Bed Fusion of Polymers
por: Sillani, Francesco, et al.
Publicado: (2021)

A Novel Approach for Powder Bed Fusion of Ceramics Using Two Laser Systems
por: Kaya, Duran, et al.
Publicado: (2023)

Processability of a Hot Work Tool Steel Powder Mixture in Laser-Based Powder Bed Fusion
por: Hantke, Nick, et al.
Publicado: (2022)

Molecular Dynamics Simulation of Fe-Based Metal Powder Oxidation during Laser Powder Bed Fusion
por: Wang, Yu, et al.
Publicado: (2022)

Design and Fabrication of Random Metal Foam Structures for Laser Powder Bed Fusion
por: Contuzzi, Nicola, et al.
Publicado: (2019)

Dynamics of pore formation during laser powder bed fusion additive manufacturing
por: Martin, Aiden A., et al.
Publicado: (2019)

Processability of Atypical WC-Co Composite Feedstock by Laser Powder-Bed Fusion
por: Al-Thamir, Mohaimen, et al.
Publicado: (2019)

Cannot write session to /tmp/vufind_sessions/sess_q04vkovg2h2u714kc48kiagpme