Cargando…

Microstructural and Tensile Properties Anisotropy of Selective Laser Melting Manufactured IN 625

The present study was focused on the assessment of microstructural anisotropy of IN 625 manufactured by selective laser melting (SLM) and its influence on the material’s room temperature tensile properties. Microstructural anisotropy was assessed based on computational and experimental investigation...

Descripción completa

Detalles Bibliográficos
Autores principales:	Condruz, Mihaela Raluca, Matache, Gheorghe, Paraschiv, Alexandru, Frigioescu, Tiberius Florian, Badea, Teodor
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2020
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC7663131/ https://www.ncbi.nlm.nih.gov/pubmed/33126747 http://dx.doi.org/10.3390/ma13214829

Ejemplares similares

The Influence of Laser Defocusing in Selective Laser Melted IN 625
por: Paraschiv, Alexandru, et al.
Publicado: (2021)

Tensile Notch Sensitivity of Additively Manufactured IN 625 Superalloy
por: Matache, Gheorghe, et al.
Publicado: (2020)

Laser Powder Bed Fusion Process Parameters’ Optimization for Fabrication of Dense IN 625
por: Paraschiv, Alexandru, et al.
Publicado: (2022)

Assessment of Additive Manufactured IN 625’s Tensile Strength Based on Nonstandard Specimens
por: Paraschiv, Alexandru, et al.
Publicado: (2023)

A Study on Mechanical Properties of Low-Cost Thermoplastic-Based Materials for Material Extrusion Additive Manufacturing
por: Condruz, Mihaela-Raluca, et al.
Publicado: (2023)

Investigation of Scanning Strategies and Laser Remelting Effects on Top Surface Deformation of Additively Manufactured IN 625
por: Paraschiv, Alexandru, et al.
Publicado: (2022)

Manufacturing of Closed Impeller for Mechanically Pump Fluid Loop Systems Using Selective Laser Melting Additive Manufacturing Technology
por: Adiaconitei, Alexandra, et al.
Publicado: (2021)

A Study on Long-Term Oxidation and Thermal Shock Performance of Nanostructured YSZ/NiCrAlY TBC with a Less Dense Bond Coat
por: Badea, Teodor-Adrian, et al.
Publicado: (2023)

Assessment of Hot Corrosion in Molten Na(2)SO(4) and V(2)O(5) of Inconel 625 Fabricated by Selective Laser Melting versus Conventional Technology
por: Badea, Teodor Adrian, et al.
Publicado: (2022)

A Study on Using the Additive Manufacturing Process for the Development of a Closed Pump Impeller for Mechanically Pumped Fluid Loop Systems
por: Adiaconitei, Alexandra, et al.
Publicado: (2021)

High Strain Rate Yielding of Additive Manufacturing Inconel 625 by Selective Laser Melting
por: Du, Kang, et al.
Publicado: (2021)

Laser Welding of SLM-Manufactured Tubes Made of IN625 and IN718
por: Jokisch, Torsten, et al.
Publicado: (2019)

A comprehensive study on microstructure and tensile behaviour of a selectively laser melted stainless steel
por: Qiu, Chunlei, et al.
Publicado: (2018)

Investigation of microstructure in additive manufactured Inconel 625 by spatially resolved neutron transmission spectroscopy
por: Tremsin, Anton S., et al.
Publicado: (2016)

Evaluation of Dispersion Methods and Mechanical Behaviour of Glass Fibre Composites with Embedded Self-Healing Systems
por: Vintila, Ionut Sebastian, et al.
Publicado: (2021)

The Interface Microstructures and Mechanical Properties of Laser Additive Repaired Inconel 625 Alloy
por: Wei, Yiyun, et al.
Publicado: (2020)

Effect of Fe Content on Microstructure and Properties of Laser Cladding Inconel 625 Alloy
por: Liu, Weidong, et al.
Publicado: (2022)

Microstructure and Selective Corrosion of Alloy 625 Obtained by Means of Laser Powder Bed Fusion
por: Cabrini, Marina, et al.
Publicado: (2019)

Precipitates in Additively Manufactured Inconel 625 Superalloy
por: Dubiel, Beata, et al.
Publicado: (2019)

Microstructure and Fatigue Damage of 316L Stainless Steel Manufactured by Selective Laser Melting (SLM)
por: Wang, Zhentao, et al.
Publicado: (2021)

Selective Laser Melting Additive Manufactured Tantalum: Effect of Microstructure and Impurities on the Strengthening-Toughing Mechanism
por: Lian, Fengjun, et al.
Publicado: (2023)

Microstructure and Properties of Inconel 625 Fabricated Using Two Types of Laser Metal Deposition Methods
por: Dutkiewicz, Jan, et al.
Publicado: (2020)

Densification, Microstructure, and Mechanical Properties of Additively Manufactured 2124 Al–Cu Alloy by Selective Laser Melting
por: Deng, Junwang, et al.
Publicado: (2020)

Formability, Microstructure and Properties of Inconel 718 Superalloy Fabricated by Selective Laser Melting Additive Manufacture Technology
por: Liu, Xiaoping, et al.
Publicado: (2021)

Stress Corrosion Cracking of Additively Manufactured Alloy 625
por: Cabrini, Marina, et al.
Publicado: (2021)

Simulation of TTT Curves for Additively Manufactured Inconel 625
por: LINDWALL, G., et al.
Publicado: (2019)

Parametric Optimization of Laser Additive Manufacturing of Inconel 625 Using Taguchi Method and Grey Relational Analysis
por: Yang, Bo, et al.
Publicado: (2020)

The Heat Treatment Influence on the Microstructure and Hardness of TC4 Titanium Alloy Manufactured via Selective Laser Melting
por: Zhao, Zhan-Yong, et al.
Publicado: (2018)

Multi-scale microstructure high-strength titanium alloy lattice structure manufactured via selective laser melting
por: Yang, Xin, et al.
Publicado: (2021)

Effect of Process Parameters on the Microstructure and Properties of Cu–Cr–Nb–Ti Alloy Manufactured by Selective Laser Melting
por: Li, Jian, et al.
Publicado: (2023)

Microstructure and Tensile Properties of Melt-Spun Filaments of Polybutene-1 and Butene-1/Ethylene Copolymer
por: Li, Jianrong, et al.
Publicado: (2023)

A Comparative Study on Microstructure and Properties of Ultra-High-Speed Laser Cladding and Traditional Laser Cladding of Inconel625 Coatings
por: Ding, Yuhang, et al.
Publicado: (2022)

Mechanical and Microstructural Characterization of Arc-Welded Inconel 625 Alloy
por: Kotzem, Daniel, et al.
Publicado: (2019)

Effect of Layer Thickness and Heat Treatment on Microstructure and Mechanical Properties of Alloy 625 Manufactured by Electron Beam Powder Bed Fusion
por: Diaz, Julio Cesar, et al.
Publicado: (2022)

Anisotropy in the Tensile Properties of a Selective Laser Melted Ti-5Al-5Mo-5V-1Cr-1Fe Alloy during Aging Treatment
por: Huang, Hualong, et al.
Publicado: (2022)

Physical–Mechanical Characteristics and Microstructure of Ti6Al7Nb Lattice Structures Manufactured by Selective Laser Melting
por: Cosma, Cosmin, et al.
Publicado: (2020)

Effects of Annealing and Solution Treatments on the Microstructure and Mechanical Properties of Ti6Al4V Manufactured by Selective Laser Melting
por: Jaber, Hassanen, et al.
Publicado: (2022)

Microstructures Manufactured in Diamond by Use of Laser Micromachining
por: Dudek, Mariusz, et al.
Publicado: (2020)

Performance Consistency of AlSi10Mg Alloy Manufactured by Simulating Multi Laser Beam Selective Laser Melting (SLM): Microstructures and Mechanical Properties
por: Liu, Bin, et al.
Publicado: (2018)

Selective Laser Melted Magnesium Alloys: Fabrication, Microstructure and Property
por: Zhou, Yun, et al.
Publicado: (2022)

Cannot write session to /tmp/vufind_sessions/sess_hchnqkm7nrrn747ocfm6hvakd9