Cargando…

In-Situ Laser Polishing Additive Manufactured AlSi10Mg: Effect of Laser Polishing Strategy on Surface Morphology, Roughness and Microhardness

Laser polishing is a widely used technology to improve the surface quality of the products. However, the investigation on the physical mechanism is still lacking. In this paper, the established numerical transient model reveals the rough surface evolution mechanism during laser polishing. Mass trans...

Descripción completa

Detalles Bibliográficos
Autores principales:	Zhou, Jiantao, Han, Xu, Li, Hui, Liu, Sheng, Shen, Shengnan, Zhou, Xin, Zhang, Dongqi
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2021
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC7830785/ https://www.ncbi.nlm.nih.gov/pubmed/33466941 http://dx.doi.org/10.3390/ma14020393

Ejemplares similares

Laser Polishing of Additively Manufactured RFQ Prototype
por: Lacis, Viesturs
Publicado: (2022)

Laser Polishing of Additive Manufactured Aluminium Parts by Modulated Laser Power
por: Hofele, Markus, et al.
Publicado: (2021)

Modification of Residual Stresses in Laser Additive Manufactured AlSi10Mg Specimens Using an Ultrasonic Peening Technique
por: Xing, Xiaodong, et al.
Publicado: (2019)

Micromechanical Modeling of AlSi10Mg Processed by Laser-Based Additive Manufacturing: From as-Built to Heat-Treated Microstructures
por: Nammalvar Raja Rajan, Aravindh, et al.
Publicado: (2022)

Corrosion Behavior of Heat-Treated AlSi10Mg Manufactured by Laser Powder Bed Fusion
por: Cabrini, Marina, et al.
Publicado: (2018)

Effects of Power and Laser Speed on the Mechanical Properties of AlSi7Mg0.6 Manufactured by Laser Powder Bed Fusion
por: Vaudreuil, Sébastien, et al.
Publicado: (2022)

Laser Additive Manufacturing of TC4/AlSi12 Bimetallic Structure via Nb Interlayer
por: Jing, Zhicheng, et al.
Publicado: (2022)

Investigation on Selective Laser Melting AlSi10Mg Cellular Lattice Strut: Molten Pool Morphology, Surface Roughness and Dimensional Accuracy
por: Han, Xuesong, et al.
Publicado: (2018)

High-Temperature Mechanical Properties of Stress-Relieved AlSi10Mg Produced via Laser Powder Bed Fusion Additive Manufacturing
por: Lehmhus, Dirk, et al.
Publicado: (2022)

Laser Polishing of Additive Manufactured 316L Stainless Steel Synthesized by Selective Laser Melting
por: Obeidi, Muhannad A., et al.
Publicado: (2019)

Aging Profiles of AlSi7Mg0.6 and AlSi10Mg0.3 Alloys Manufactured via Laser-Powder Bed Fusion: Direct Aging versus T6
por: Cerri, Emanuela, et al.
Publicado: (2022)

Effects of Wet and Dry Finishing and Polishing on Surface Roughness and Microhardness of Composite Resins
por: Nasoohi, Negin, et al.
Publicado: (2017)

Effective Mechanical Properties of AlSi7Mg Additively Manufactured Cubic Lattice Structures
por: Mantovani, Sara, et al.
Publicado: (2022)

Performance Consistency of AlSi10Mg Alloy Manufactured by Simulating Multi Laser Beam Selective Laser Melting (SLM): Microstructures and Mechanical Properties
por: Liu, Bin, et al.
Publicado: (2018)

Research on Microstructure and Properties of AlSi10Mg Fabricated by Selective Laser Melting
por: Pan, Wei, et al.
Publicado: (2022)

Failure Analysis of the Tree Column Structures Type AlSi10Mg Alloy Branches Manufactured by Selective Laser Melting
por: Bai, Peikang, et al.
Publicado: (2020)

Effect of Heat Treatment on Gradient Microstructure of AlSi10Mg Lattice Structure Manufactured by Laser Powder Bed Fusion
por: Liu, Mulin, et al.
Publicado: (2020)

Surface Topographic Features after Milling of Additively Manufactured AlSi10Mg Aluminum Alloy
por: Struzikiewicz, Grzegorz, et al.
Publicado: (2022)

Multiobjective Optimization of Laser Polishing of Additively Manufactured Ti-6Al-4V Parts for Minimum Surface Roughness and Heat-Affected Zone
por: Solheid, Juliana S., et al.
Publicado: (2022)

AlSi10Mg in Powder Bed Fusion with Laser Beam: An Old and Boring Material?
por: Rasch, Michael, et al.
Publicado: (2022)

Investigation of Surface Integrity of Selective Laser Melting Additively Manufactured AlSi10Mg Alloy under Ultrasonic Elliptical Vibration-Assisted Ultra-Precision Cutting
por: Tan, Rongkai, et al.
Publicado: (2022)

Work Hardening of Heat-Treated AlSi10Mg Alloy Manufactured by Single and Double Laser Selective Laser Melting: Effects of Layer Thickness and Hatch Spacing
por: Ghio, Emanuele, et al.
Publicado: (2021)

LCLS Laser (in Polish)
por: Romaniuk, R S
Publicado: (2013)

Microstructure and Mechanical Properties of Nanoparticulate Y(2)O(3) Modified AlSi10Mg Alloys Manufactured by Selective Laser Melting
por: Zhang, Fuxu, et al.
Publicado: (2023)

The Effect of Silicon Phase Morphology on Microstructure and Properties of AlSi10Mg Alloys Fabricated by Selective Laser Melting
por: Wu, Liyun, et al.
Publicado: (2022)

On the Selective Laser Melting (SLM) of the AlSi10Mg Alloy: Process, Microstructure, and Mechanical Properties
por: Trevisan, Francesco, et al.
Publicado: (2017)

Influence of Selective Laser Melting Machine Source on the Dynamic Properties of AlSi10Mg Alloy
por: Amir, Ben, et al.
Publicado: (2019)

The effect of one-step and multi-step polishing systems on the surface roughness and microhardness of novel resin composites
por: Erdemir, Ugur, et al.
Publicado: (2012)

Finishing and polishing effects of multiblade burs on the surface texture of 5 resin composites: microhardness and roughness testing
por: Ehrmann, Elodie, et al.
Publicado: (2018)

Study of Size Effect on Microstructure and Mechanical Properties of AlSi10Mg Samples Made by Selective Laser Melting
por: Dong, Zhichao, et al.
Publicado: (2018)

Parameter Optimization of RB-SiC Polishing by Femtosecond Laser
por: Yang, Tingkai, et al.
Publicado: (2023)

A Comparative Study of Corrosion AA6061 and AlSi10Mg Alloys Produced by Extruded and Additive Manufacturing
por: Estupiñan-López, Francisco, et al.
Publicado: (2021)

Comparison of Various Intrinsic Defect Criteria to Plot Kitagawa–Takahashi Diagrams in Additively Manufactured AlSi10Mg
por: Nur, Mohammed Intishar, et al.
Publicado: (2023)

FEM Simulation of AlSi10Mg Artifact for Additive Manufacturing Process Calibration with Industrial-Computed Tomography Validation
por: Patuelli, Cesare, et al.
Publicado: (2023)

Impacts of Defocusing Amount and Molten Pool Boundaries on Mechanical Properties and Microstructure of Selective Laser Melted AlSi10Mg
por: Zhou, Suyuan, et al.
Publicado: (2018)

Additive Manufacturing of AlSi10Mg and Ti6Al4V Lightweight Alloys via Laser Powder Bed Fusion: A Review of Heat Treatments Effects
por: Ghio, Emanuele, et al.
Publicado: (2022)

In Situ Mo(Si,Al)(2)-Based Composite through Selective Laser Melting of a MoSi(2)-30 wt.% AlSi10Mg Mixture
por: Minasyan, Tatevik, et al.
Publicado: (2020)

Solute clustering and supersaturated solid solution of AlSi10Mg alloy fabricated by selective laser melting
por: Maeshima, Takashi, et al.
Publicado: (2019)

Investigation on the Microstructure and Mechanical Properties of CNTs-AlSi10Mg Composites Fabricated by Selective Laser Melting
por: Luo, Shixuan, et al.
Publicado: (2021)

Effects of Processing Parameters of Selective Laser Melting Process on Thermal Conductivity of AlSi10Mg Alloy
por: Kim, Moo-Sun
Publicado: (2021)

Cannot write session to /tmp/vufind_sessions/sess_548vmu90rgcv3n5hprtb3miopb