Cargando…

Fused Filament Deposition of PLA: The Role of Interlayer Adhesion in the Mechanical Performances

A set of criteria to enhance mechanical performances of standard specimens (Type V, ANSI D368) made of polylactic acid (PLA) were proposed. Fused PLA deposition was conducted with nozzle temperature ranging from 180 to 230 °C and deposition plate temperature ranging from 70 to 110 °C. Optical micros...

Descripción completa

Detalles Bibliográficos
Autores principales:	Liparoti, Sara, Sofia, Daniele, Romano, Aldo, Marra, Francesco, Pantani, Roberto
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2021
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC7865617/ https://www.ncbi.nlm.nih.gov/pubmed/33513767 http://dx.doi.org/10.3390/polym13030399

Ejemplares similares

Replication of Micro- and Nanofeatures in Injection Molding of Two PLA Grades with Rapid Surface-Temperature Modulation
por: Liparoti, Sara, et al.
Publicado: (2018)

Thermal Properties and In Vitro Biodegradation of PLA-Mg Filaments for Fused Deposition Modeling
por: Leonés, Adrián, et al.
Publicado: (2023)

Performance Analysis of Colored PLA Products with a Fused Filament Fabrication Process
por: Spina, Roberto
Publicado: (2019)

Effect of Ultrasonic Vibration on Interlayer Adhesion in Fused Filament Fabrication 3D Printed ABS
por: Tofangchi, Alireza, et al.
Publicado: (2019)

Development of Antimicrobial PLA Composites for Fused Filament Fabrication
por: Brounstein, Zachary, et al.
Publicado: (2021)

The Mechanical, Thermal, and Chemical Properties of PLA-Mg Filaments Produced via a Colloidal Route for Fused-Filament Fabrication
por: Orellana-Barrasa, Jaime, et al.
Publicado: (2022)

Effects of Accelerating the Ageing of 1D PLA Filaments after Fused Filament Fabrication
por: Orellana-Barrasa, Jaime, et al.
Publicado: (2022)

Investigating the Material Properties and Microstructural Changes of Fused Filament Fabricated PLA and Tough-PLA Parts
por: Naveed, Nida
Publicado: (2021)

Potential for Natural Fiber Reinforcement in PLA Polymer Filaments for Fused Deposition Modeling (FDM) Additive Manufacturing: A Review
por: Lee, Ching Hao, et al.
Publicado: (2021)

Rheological Characterization and Printability of Polylactide (PLA)-Alumina (Al(2)O(3)) Filaments for Fused Deposition Modeling (FDM)
por: Smirnov, Anton, et al.
Publicado: (2022)

Mechanical and Geometric Performance of PLA-Based Polymer Composites Processed by the Fused Filament Fabrication Additive Manufacturing Technique
por: Reverte, José María, et al.
Publicado: (2020)

Preparation of Hydrophobic Surface on PLA and ABS by Fused Deposition Modeling
por: Yang, Huadong, et al.
Publicado: (2020)

Effect of Rapid Mold Heating on the Structure and Performance of Injection-Molded Polypropylene
por: Liparoti, Sara, et al.
Publicado: (2020)

Establishing a Framework for Fused Filament Fabrication Process Optimization: A Case Study with PLA Filaments
por: Grubbs, Jack, et al.
Publicado: (2023)

The Transferability and Design of Commercial Printer Settings in PLA/PBAT Fused Filament Fabrication
por: Wang, Sisi, et al.
Publicado: (2020)

The Mechanical Properties of Thin-Walled Specimens Printed from a Bronze-Filled PLA-Based Composite Filament Using Fused Deposition Modelling
por: Bochnia, Jerzy, et al.
Publicado: (2023)

In-vitro evaluation of Polylactic acid (PLA) manufactured by fused deposition modeling
por: Wurm, Matthias C., et al.
Publicado: (2017)

Independent Evaluation of Medical-Grade Bioresorbable Filaments for Fused Deposition Modelling/Fused Filament Fabrication of Tissue Engineered Constructs
por: Mohseni, Mina, et al.
Publicado: (2018)

The Influence of the Process Parameters on the Mechanical Properties of PLA Specimens Produced by Fused Filament Fabrication—A Review
por: Cojocaru, Vasile, et al.
Publicado: (2022)

Process Induced Morphology Development of Isotactic Polypropylene on the Basis of Molecular Stretch and Mechanical Work Evolutions
por: Liparoti, Sara, et al.
Publicado: (2019)

Effect of Printing Parameters on Mechanical Behaviour of PLA-Flax Printed Structures by Fused Deposition Modelling
por: Belarbi, Yassine Elias, et al.
Publicado: (2021)

Filament Advance Detection Sensor for Fused Deposition Modelling 3D Printers
por: Soriano Heras, Enrique, et al.
Publicado: (2018)

Microstructure and Mechanical Performance of 3D Printed Wood-PLA/PHA Using Fused Deposition Modelling: Effect of Printing Temperature
por: Guessasma, Sofiane, et al.
Publicado: (2019)

Filaments Production and Fused Deposition Modelling of ABS/Carbon Nanotubes Composites
por: Dul, Sithiprumnea, et al.
Publicado: (2018)

Exploring Environmental Settings to Improve the Printability of Paroxetine-Loaded Filaments by Fused Deposition Modelling
por: Figueiredo, Sara, et al.
Publicado: (2023)

Hygromechanical Performance of Polyamide Specimens Made with Fused Filament Fabrication
por: Spina, Roberto, et al.
Publicado: (2021)

The Influence of Raster Angle and Moisture Content on the Mechanical Properties of PLA Parts Produced by Fused Deposition Modeling
por: Algarni, Mohammed
Publicado: (2021)

Hierarchical Structure of iPP During Injection Molding Process with Fast Mold Temperature Evolution
por: Speranza, Vito, et al.
Publicado: (2019)

Correction: Speranza, V. et al. Hierarchical Structure of iPP During Injection Molding Process with Fast Mold Temperature Evolution. Materials 2019, 12, 424
por: Speranza, Vito, et al.
Publicado: (2020)

Multi-Scale Simulation of Injection Molding Process with Micro–Features Replication: Relevance of Rheological Behaviour and Crystallization
por: Liparoti, Sara, et al.
Publicado: (2021)

The Extent of Interlayer Bond Strength during Fused Filament Fabrication of Nylon Copolymers: An Interplay between Thermal History and Crystalline Morphology
por: Vaes, Dries, et al.
Publicado: (2021)

Composite Polyurethane-Polylactide (PUR/PLA) Flexible Filaments for 3D Fused Filament Fabrication (FFF) of Antibacterial Wound Dressings for Skin Regeneration
por: Szarlej, Paweł, et al.
Publicado: (2021)

Effective Stiffness of Fused Deposition Modeling Infill Lattice Patterns Made of PLA-Wood Material
por: Cuan-Urquizo, Enrique, et al.
Publicado: (2022)

Improvement of the Gas Barrier Properties of PLA/OMMT Films by Regulating the Interlayer Spacing of OMMT and the Crystallinity of PLA
por: Li, Fenfen, et al.
Publicado: (2020)

Impact Toughness of Hybrid Carbon Fiber-PLA/ABS Laminar Composite Produced through Fused Filament Fabrication
por: Ahmed, Hafiz, et al.
Publicado: (2021)

Characterization of Optimized Ternary PLA/PHB/Organoclay Composites Processed through Fused Filament Fabrication and Injection Molding
por: Buyuksoy-Fekraoui, Kubra, et al.
Publicado: (2022)

Sterilization of PLA after Fused Filament Fabrication 3D Printing: Evaluation on Inherent Sterility and the Impossibility of Autoclavation
por: Neijhoft, Jonas, et al.
Publicado: (2023)

Filament Breakage Monitoring in Fused Deposition Modeling Using Acoustic Emission Technique
por: Yang, Zhensheng, et al.
Publicado: (2018)

Electrically Conductive Polyetheretherketone Nanocomposite Filaments: From Production to Fused Deposition Modeling
por: Gonçalves, Jordana, et al.
Publicado: (2018)

Preparation of Polylactic Acid/Calcium Peroxide Composite Filaments for Fused Deposition Modelling
por: Mohammed, Abdullah H., et al.
Publicado: (2023)

Cannot write session to /tmp/vufind_sessions/sess_2ej4efqkgei4ole2uau92cjqcp