Cargando…

Novel powder processing technologies for production of rare-earth permanent magnets

Post-neodymium magnets that possess high heat resistance, coercivity, and (BH)(max) are desired for future-generation motors. However, the candidate materials for post-neodymium magnets such as Sm(2)Fe(17)N(3) and metastable magnetic alloys have certain process-related problems: low sinterability du...

Descripción completa

Detalles Bibliográficos
Autores principales:	Takagi, Kenta, Hirayama, Yusuke, Okada, Shusuke, Yamaguchi, Wataru, Ozaki, Kimihiro
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	Taylor & Francis 2021
Materias:	Focus Issue: Science and Technology of Element-Strategic Permanent Magnets
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC7935123/ https://www.ncbi.nlm.nih.gov/pubmed/33716571 http://dx.doi.org/10.1080/14686996.2021.1875791

Ejemplares similares

Synthesis of mesoscopic particles of multi-component rare earth permanent magnet compounds
por: Trinh, T. Thuy, et al.
Publicado: (2021)

First-principles determination of intergranular atomic arrangements and magnetic properties in rare-earth permanent magnets
por: Gohda, Yoshihiro
Publicado: (2021)

First-principles calculations of magnetic properties for analysis of magnetization processes in rare-earth permanent magnets
por: Tsuchiura, Hiroki, et al.
Publicado: (2021)

Foreword to the Focus Issue: science and technology of element-strategic permanent magnets
por: Hirosawa, Satoshi, et al.
Publicado: (2022)

Recent advances in SmFe(12)-based permanent magnets
por: Takahashi, Y. K., et al.
Publicado: (2021)

Experimental approaches for micromagnetic coercivity analysis of advanced permanent magnet materials
por: Okamoto, Satoshi
Publicado: (2021)

Development of a prototype thermodynamic database for Nd-Fe-B permanent magnets
por: Abe, Taichi, et al.
Publicado: (2021)

Recent progress in the development of high-performance bonded magnets using rare earth–Fe compounds
por: Horikawa, Takashi, et al.
Publicado: (2021)

Atomistic theory of thermally activated magnetization processes in Nd(2)Fe(14)B permanent magnet
por: Miyashita, Seiji, et al.
Publicado: (2021)

Most frequently asked questions about the coercivity of Nd-Fe-B permanent magnets
por: Li, Jiangnan, et al.
Publicado: (2021)

Understanding and optimization of hard magnetic compounds from first principles
por: Miyake, Takashi, et al.
Publicado: (2021)

Computational thermodynamics and microstructure simulations to understand the role of grain boundary phase in Nd-Fe-B hard magnets
por: Koyama, Toshiyuki, et al.
Publicado: (2021)

High performance hot-deformed Nd-Fe-B magnets (Review)
por: Hioki, Keiko
Publicado: (2021)

The Case of the Discharged Consumptive
Publicado: (1918)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

Massive transformation in FeNi nanopowders with nanotwin-assisted nitridation
por: Wang, Jian, et al.
Publicado: (2022)

Down to Earth: The Emerging Field of Planetary Health
por: Seltenrich, Nate
Publicado: (2018)

Calibrating a thermometer for Earth’s interior over time
por: Asimow, Paul D.
Publicado: (2022)

New filter coating helps fight viruses
Publicado: (2021)

Pandemic proves need for clean air
Publicado: (2021)

CMS Solenoid Magnet during Long Shutdown 1 (LS1)
por: Hoch, Micheal
Publicado: (2013)

Installation at Point 5 of the dump resistors for the CMS magnet surface tests.
por: B. CURE
Publicado: (2004)

Manufacturing of the test cryostat. The test cryostat is used to simulate heat loads of the CMS magnet for the acceptance tests of the refrigeration system.
por: Goran Perinic
Publicado: (2002)

Montage photograph: Cryogenic components mounted on top of the central yoke barrel in the configuration for the acceptance tests of the helium refrigeration system comprising the intermediate cryostat (right), the test cryostat (left) and the cryogenic transfer lines.
por: Goran Perinic
Publicado: (2003)

Cryogenic cold box during installation.
por: Goran Perinic
Publicado: (2003)

Installation of the intermediate cryostat.
por: Goran Perinic
Publicado: (2003)

Lowering of the cryogenic transfer line segments to USC55.
por: Goran Perinic
Publicado: (2004)

First plate of LHCb Magnet Yoke in place
por: Lindner, R.
Publicado: (2003)

CB-2 ready for impregnation
por: P. Fabbricatore
Publicado: (2003)

CB0 is finished machining, and for CB+1 the shell is finished.
por: P. Fabbricatore
Publicado: (2003)

Winding of CB-1
por: P. Fabbricatore
Publicado: (2003)

Zstop end cap load test
por: Pascal Petiot
Publicado: (2003)

LHCb Magnet assembly status
por: Koppenburg, P
Publicado: (2004)

Loading of CB-2 in Genova harbour
por: Ansaldo
Publicado: (2004)

Travel of CB-2 towards Point 5
por: L. Veillet
Publicado: (2004)

Unloading of CB-2 at Point 5
por: L. Veillet
Publicado: (2004)

CMS superconducting solenoid model coil
por: Perrella, M
Publicado: (2000)

CMS superconducting solenoid yoke
por: Brice, M, et al.
Publicado: (2008)

Images of CMS Superconducting Solonoid - Ancillaries
por: Perinic, G, et al.
Publicado: (2008)

Endcap sector block being maneuvered in KHI hall (Kawasaki Heavy Industry)
Publicado: (2000)

Cannot write session to /tmp/vufind_sessions/sess_a9kpooire45lsq0uin8cb2mpif