Cargando…

Cutting Forces and Tool Wear Investigation during Turning of Sintered Nickel-Cobalt Alloy with CBN Tools

This article describes issues related to the machining of parts made of sintered nickel-cobalt alloy. Longitudinal turning with a CBN (cubic boron nitride) tool was analyzed. The results of experiments showed the influence of cutting parameters in the field of finishing machining on the values of cu...

Descripción completa

Detalles Bibliográficos
Autores principales:	Zębala, Wojciech, Struzikiewicz, Grzegorz, Rumian, Ksenia
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2021
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC8036654/ https://www.ncbi.nlm.nih.gov/pubmed/33810472 http://dx.doi.org/10.3390/ma14071623

Ejemplares similares

Method of Data Selection for Turning of Inconel 718 Alloy Obtained by Casting and Laser Sintering Powder
por: Latosińska, Ksenia, et al.
Publicado: (2022)

Optimization of Cutting Data and Tool Inclination Angles During Hard Milling with CBN Tools, Based on Force Predictions and Surface Roughness Measurements
por: Matras, Andrzej, et al.
Publicado: (2020)

Turning Titanium Alloy, Grade 5 ELI, With the Implementation of High Pressure Coolant
por: Słodki, Bogdan, et al.
Publicado: (2019)

Reduction of Power Consumption by Chip Breakability Control in Ti6Al4V Titanium Alloy Turning
por: Zębala, Wojciech, et al.
Publicado: (2020)

Investigation of the Cutting Fluid Incidence Angle Direction in Turning Grade 5 ELI Titanium Alloy under High-Pressure Cooling Conditions
por: Struzikiewicz, Grzegorz
Publicado: (2023)

Influence of Different Grades of CBN Inserts on Cutting Force and Surface Roughness of AISI H13 Die Tool Steel during Hard Turning Operation
por: Kumar, Pardeep, et al.
Publicado: (2019)

Effects of Machining Parameters and Tool Reconditioning on Cutting Force, Tool Wear, Surface Roughness and Burr Formation in Nickel-Based Alloy Milling
por: Kónya, Gábor, et al.
Publicado: (2023)

Experimental data-set for prediction of tool wear during turning of Al-1061 alloy by high speed steel cutting tools
por: Okokpujie, I.P., et al.
Publicado: (2018)

Tribological Aspects of Cutting Tool Wear during the Turning of Stainless Steels
por: Zawada-Michałowska, Magdalena, et al.
Publicado: (2019)

Optimization and prediction of CBN tool life sustainability during AA1100 CNC turning by response surface methodology
por: H, Faisal M., et al.
Publicado: (2023)

Turning Copper and Aluminum Alloys with Natural Rocks as Cutting Tools
por: Breidenstein, Bernd, et al.
Publicado: (2022)

Evaluation of Surface Roughness and Defect Formation after The Machining of Sintered Aluminum Alloy AlSi10Mg
por: Struzikiewicz, Grzegorz, et al.
Publicado: (2020)

Turning Research of Additive Laser Molten Stainless Steel 316L Obtained by 3D Printing
por: Struzikiewicz, Grzegorz, et al.
Publicado: (2019)

Optimization of Cutting Parameters in Turning of Titanium Alloy (Grade 5) by Analysing Surface Roughness, Tool Wear and Energy Consumption
por: Akkuş, H., et al.
Publicado: (2021)

Comparison of Tool Wear, Surface Roughness, Cutting Forces, Tool Tip Temperature, and Chip Shape during Sustainable Turning of Bearing Steel
por: Demirpolat, Havva, et al.
Publicado: (2023)

Tool Wear and Surface Roughness in Turning of Metal Matrix Composite Built of Al(2)O(3) Sinter Saturated by Aluminum Alloy in Vacuum Condition
por: Szymański, Michał, et al.
Publicado: (2022)

Study on the CBN Wheel Wear Mechanism of Longitudinal-Torsional Ultrasonic-Assisted Grinding Applied to TC4 Titanium Alloy
por: Liu, Junli, et al.
Publicado: (2022)

Nickel, cobalt, and their alloys
por: Davis, J. R
Publicado: (2000)

Surface Integrity and Tool Wear Analysis on Turning of Copper-Nickel 70/30 ASTM B122 Alloy under Low Initial Lubrication
por: García-Martínez, Enrique, et al.
Publicado: (2021)

Turning Tool Wear Estimation Based on the Calculated Parameter Values of the Thermodynamic Subsystem of the Cutting System
por: Lapshin, Victor Petrovich
Publicado: (2021)

The Precision Analysis of Cutting Edge Preparation on CBN Cutting Inserts Using Rotary Ultrasonic Machining
por: Kuruc, Marcel, et al.
Publicado: (2022)

Research and Method of Roughness Prediction of a Curvilinear Surface after Titanium Alloy Turning
por: Matras, Andrzej, et al.
Publicado: (2019)

Comparative Evaluation of Surface Quality, Tool Wear, and Specific Cutting Energy for Wiper and Conventional Carbide Inserts in Hard Turning of AISI 4340 Alloy Steel
por: Abbas, Adel T., et al.
Publicado: (2020)

The Research of Tool Wear Mechanism for High-Speed Milling ADC12 Aluminum Alloy Considering the Cutting Force Effect
por: Meng, Xinxin, et al.
Publicado: (2021)

Fractal Characteristics of Chip Morphology and Tool Wear in High-Speed Turning of Iron-Based Super Alloy
por: Zhang, Xu, et al.
Publicado: (2020)

Influence of Electroplated CBN Wheel Wear on Grinding Surface Morphology of Powder Metallurgy Superalloy FGH96
por: Wang, Haining, et al.
Publicado: (2020)

Micro-Milling Tool Wear Monitoring via Nonlinear Cutting Force Model
por: Liu, Tongshun, et al.
Publicado: (2022)

Investigations on Surface Roughness and Tool Wear Characteristics in Micro-Turning of Ti-6Al-4V Alloy
por: Aslantas, Kubilay, et al.
Publicado: (2020)

Tool Condition Monitoring of the Cutting Capability of a Turning Tool Based on Thermography
por: Brili, Nika, et al.
Publicado: (2021)

Generic Cutting Force Modeling with Comprehensively Considering Tool Edge Radius, Tool Flank Wear and Tool Runout in Micro-End Milling
por: Gao, Shuaishuai, et al.
Publicado: (2022)

Lifespan of super-alloy Waspaloy cutting tools
por: Chen, Shao-Hsien, et al.
Publicado: (2019)

Production of High-Purity Anhydrous Nickel(II) Perrhenate for Tungsten-Based Sintered Heavy Alloys
por: Leszczyńska-Sejda, Katarzyna, et al.
Publicado: (2017)

Method for an Effective Selection of Tools and Cutting Conditions during Precise Turning of Non-Alloy Quality Steel C45
por: Ivchenko, Oleksandr, et al.
Publicado: (2022)

Tribological Performance of Micro-Groove Tools of Improving Tool Wear Resistance in Turning AISI 304 Process
por: Wu, Jinxing, et al.
Publicado: (2020)

Grinding Force and Surface Formation Mechanisms of 17CrNi2MoVNb Alloy When Grinding with CBN and Alumina Wheels
por: Jiang, Xiaoyang, et al.
Publicado: (2023)

Study of Wear, Stress and Vibration Characteristics of Silicon Carbide Tool Inserts and Nano Multi-Layered Titanium Nitride-Coated Cutting Tool Inserts in Turning of SS304 Steels
por: Ganeshkumar, S., et al.
Publicado: (2022)

Tool Wear Mechanism in Cutting of Stack CFRP/UNS A97075
por: Fernandez-Vidal, Severo Raul, et al.
Publicado: (2018)

Smart Cutting Tools Used in the Processing of Aluminum Alloys
por: Dobrotă, Dan, et al.
Publicado: (2021)

Tool Wear Effect on Surface Integrity in AISI 1045 Steel Dry Turning
por: Magalhães, Laurence Colares, et al.
Publicado: (2022)

Tailored Laser Structuring of Tungsten Carbide Cutting Tools for Improving Their Tribological Performance in Turning Aluminum Alloy Al6061 T6
por: Baumann, Robert, et al.
Publicado: (2023)

Cannot write session to /tmp/vufind_sessions/sess_s5sj072i5gbn4ke9l8rgbua1et