Cargando…

Development of a prototype thermodynamic database for Nd-Fe-B permanent magnets

For the Nd-Fe-B permanent magnets, a prototype thermodynamic database of the 8-element system (Nd, Fe, B, Al, Co, Cu, Dy, Ga) was constructed based on literature data and assessed parameters in the present work. The magnetic excess Gibbs energy of the Nd(2)Fe(14)B compound was reassessed using thoro...

Descripción completa

Detalles Bibliográficos
Autores principales:	Abe, Taichi, Morishita, Masao, Chen, Ying, Saengdeejing, Arkapol, Hashimoto, Kiyoshi, Kobayashi, Yoshinao, Ohnuma, Ikuo, Koyama, Toshiyuki, Hirosawa, Satoshi
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	Taylor & Francis 2021
Materias:	Focus on Science and Technology of Element-Strategic Permanent Magnets
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC8344238/ https://www.ncbi.nlm.nih.gov/pubmed/34377084 http://dx.doi.org/10.1080/14686996.2021.1936627

Ejemplares similares

Computational thermodynamics and microstructure simulations to understand the role of grain boundary phase in Nd-Fe-B hard magnets
por: Koyama, Toshiyuki, et al.
Publicado: (2021)

Atomistic theory of thermally activated magnetization processes in Nd(2)Fe(14)B permanent magnet
por: Miyashita, Seiji, et al.
Publicado: (2021)

Foreword to the Focus Issue: science and technology of element-strategic permanent magnets
por: Hirosawa, Satoshi, et al.
Publicado: (2022)

Most frequently asked questions about the coercivity of Nd-Fe-B permanent magnets
por: Li, Jiangnan, et al.
Publicado: (2021)

Recent advances in SmFe(12)-based permanent magnets
por: Takahashi, Y. K., et al.
Publicado: (2021)

Experimental approaches for micromagnetic coercivity analysis of advanced permanent magnet materials
por: Okamoto, Satoshi
Publicado: (2021)

Synthesis of mesoscopic particles of multi-component rare earth permanent magnet compounds
por: Trinh, T. Thuy, et al.
Publicado: (2021)

High performance hot-deformed Nd-Fe-B magnets (Review)
por: Hioki, Keiko
Publicado: (2021)

First-principles determination of intergranular atomic arrangements and magnetic properties in rare-earth permanent magnets
por: Gohda, Yoshihiro
Publicado: (2021)

First-principles calculations of magnetic properties for analysis of magnetization processes in rare-earth permanent magnets
por: Tsuchiura, Hiroki, et al.
Publicado: (2021)

Recent progress in the development of high-performance bonded magnets using rare earth–Fe compounds
por: Horikawa, Takashi, et al.
Publicado: (2021)

Novel powder processing technologies for production of rare-earth permanent magnets
por: Takagi, Kenta, et al.
Publicado: (2021)

Understanding and optimization of hard magnetic compounds from first principles
por: Miyake, Takashi, et al.
Publicado: (2021)

The Case of the Discharged Consumptive
Publicado: (1918)

Winding of prototype.
por: Ansaldo
Publicado: (2002)

Insertion of prototype in impregnation autoclave
por: Ansaldo
Publicado: (2002)

Preparation of winding prototype at S. Giorgio Siegen.
por: Pasquale Fabbricatore
Publicado: (2001)

Photos of endcap disk connection prototype
por: Farshid Feyzi
Publicado: (2000)

Impregnation chamber close with prototype inside
por: Ansalso
Publicado: (2002)

Winding Prototype has been impregnated.
por: Ansaldo
Publicado: (2002)

Manufacture of the winding prototype mandrel at San Giorgio.
por: P. Fabbricatore
Publicado: (2001)

Prototype of corner piece between two endcap disks.
por: F. Feyzi
Publicado: (2001)

First turns of insulated conductor at S. Giorgio inside the winding prototype mandrel.
por: Pasquale Fabbricatore
Publicado: (2001)

Situation on 15 May 2002, mandrel CB-2 et CB-1, prototype & impregnation chamber
por: Ansaldo
Publicado: (2002)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

CMS Solenoid Magnet during Long Shutdown 1 (LS1)
por: Hoch, Micheal
Publicado: (2013)

Installation at Point 5 of the dump resistors for the CMS magnet surface tests.
por: B. CURE
Publicado: (2004)

Manufacturing of the test cryostat. The test cryostat is used to simulate heat loads of the CMS magnet for the acceptance tests of the refrigeration system.
por: Goran Perinic
Publicado: (2002)

Montage photograph: Cryogenic components mounted on top of the central yoke barrel in the configuration for the acceptance tests of the helium refrigeration system comprising the intermediate cryostat (right), the test cryostat (left) and the cryogenic transfer lines.
por: Goran Perinic
Publicado: (2003)

Cryogenic cold box during installation.
por: Goran Perinic
Publicado: (2003)

Installation of the intermediate cryostat.
por: Goran Perinic
Publicado: (2003)

Lowering of the cryogenic transfer line segments to USC55.
por: Goran Perinic
Publicado: (2004)

First plate of LHCb Magnet Yoke in place
por: Lindner, R.
Publicado: (2003)

CB-2 ready for impregnation
por: P. Fabbricatore
Publicado: (2003)

CB0 is finished machining, and for CB+1 the shell is finished.
por: P. Fabbricatore
Publicado: (2003)

Winding of CB-1
por: P. Fabbricatore
Publicado: (2003)

Zstop end cap load test
por: Pascal Petiot
Publicado: (2003)

LHCb Magnet assembly status
por: Koppenburg, P
Publicado: (2004)

Loading of CB-2 in Genova harbour
por: Ansaldo
Publicado: (2004)

Travel of CB-2 towards Point 5
por: L. Veillet
Publicado: (2004)

Cannot write session to /tmp/vufind_sessions/sess_hgdl9j7h41naaq0nve1a43rq48