Cargando…

Improved Cell Morphology and Surface Roughness in High-Temperature Foam Injection Molding Using a Long-Chain Branched Polypropylene

Long-chain branched polypropylene (LCB PP) has been used extensively to improve cell morphologies in foaming applications. However, most research focuses on low melt flow rate (MFR) resins, whereas foam production methods such as mold-opening foam injection molding (MO-FIM) require high-MFR resins t...

Descripción completa

Detalles Bibliográficos
Autores principales:	Mendoza-Cedeno, Steven, Kweon, Mu Sung, Newby, Sarah, Shivokhin, Maksim, Pehlert, George, Lee, Patrick C.
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2021
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC8348131/ https://www.ncbi.nlm.nih.gov/pubmed/34372006 http://dx.doi.org/10.3390/polym13152404

Ejemplares similares

Tuning High and Low Temperature Foaming Behavior of Linear and Long-Chain Branched Polypropylene via Partial and Complete Melting
por: Kweon, Mu Sung, et al.
Publicado: (2021)

Effect of Mold Temperature on the Impact Behavior and Morphology of Injection Molded Foams Based on Polypropylene Polyethylene–Octene Copolymer Blends
por: Muñoz-Pascual, Santiago, et al.
Publicado: (2019)

Effect of Compatibility on the Foaming Behavior of Injection Molded Polypropylene and Polycarbonate Blend Parts
por: Su, Bei, et al.
Publicado: (2019)

Effects of Injection Molding Process Parameters on the Chemical Foaming Behavior of Polypropylene and Polystyrene
por: Chung, Chen-Yuan, et al.
Publicado: (2021)

Modeling and Analysis of Morphology of Injection Molding Polypropylene Parts Induced by In-Mold Annealing
por: Salomone, Rita, et al.
Publicado: (2022)

An Approach to the Impact Simulation on Foamed Injection Molded Polypropylene Parts: An Example of Application in the Automotive Industry
por: Nutini, Massimo, et al.
Publicado: (2023)

Study on the Flow, Foaming Characteristics and Structural Strength of Polypropylene Structural Foam Injection Molding by Innovative Nitrogen and Molten Plastic Mixing Mechanism
por: Huang, Po-Wei, et al.
Publicado: (2023)

Effect of Rapid Mold Heating on the Structure and Performance of Injection-Molded Polypropylene
por: Liparoti, Sara, et al.
Publicado: (2020)

Post-Molding Shrinkage, Structure and Properties of Cellular Injection-Molded Polypropylene
por: Kościuszko, Artur, et al.
Publicado: (2022)

Effects of chain extender on properties and foaming behavior of polypropylene foam
por: Kim, Do Young, et al.
Publicado: (2019)

Effects of Injection Molding Parameters on Properties of Insert-Injection Molded Polypropylene Single-Polymer Composites
por: Wang, Jian, et al.
Publicado: (2021)

Effect of Cellulose Nanofiber (CNF) Surface Treatment on Cellular Structures and Mechanical Properties of Polypropylene/CNF Nanocomposite Foams via Core-Back Foam Injection Molding
por: Wang, Long, et al.
Publicado: (2019)

Injection Molded Novel Biocomposites from Polypropylene and Sustainable Biocarbon
por: Abdelwahab, Mohamed A., et al.
Publicado: (2019)

Insights on the Molecular Behavior of Polypropylene in the Process of Ultrasonic Injection Molding
por: Iturbe-Ek, Jackeline, et al.
Publicado: (2021)

Mechanical Properties Distribution within Polypropylene Injection Molded Samples: Effect of Mold Temperature under Uneven Thermal Conditions
por: Liparoti, Sara, et al.
Publicado: (2017)

Morphology-Mechanical Performance Relationship at the Micrometrical Level within Molded Polypropylene Obtained with Non-Symmetric Mold Temperature Conditioning
por: Liparoti, Sara, et al.
Publicado: (2021)

Injection-Molded Isotactic Polypropylene Colored with Green Transparent and Opaque Pigments
por: Janostik, Vaclav, et al.
Publicado: (2023)

Effects of Cavity Thickness and Mold Surface Roughness on the Polymer Flow during Micro Injection Molding
por: Li, Jiquan, et al.
Publicado: (2023)

Direct In-Mold Impregnation of Glass Fiber Fabric by Polypropylene with Supercritical Nitrogen in Microcellular Injection Molding Process
por: He, Qichao, et al.
Publicado: (2023)

Influence of the Molar Mass on Long-Chain Branching of Polypropylene
por: Kamleitner, Florian, et al.
Publicado: (2017)

Backpressure Optimization in Foam Injection Molding: Method and Assessment of Sustainability
por: Kastner, Clemens, et al.
Publicado: (2020)

Post-Processing Time Dependence of Shrinkage and Mechanical Properties of Injection-Molded Polypropylene
por: Kościuszko, Artur, et al.
Publicado: (2020)

Tomographic and Tension Analysis of Polypropylene Reinforced with Carbon Fiber Fabric by Injection Molding
por: Wieczorowski, Michal, et al.
Publicado: (2023)

Mechanical Properties of Injection Molded PP/PET-Nanofibril Composites and Foams
por: Mark, Lun Howe, et al.
Publicado: (2022)

Improving Rheological and Mechanical Properties of Various Virgin and Recycled Polypropylenes by Blending with Long-Chain Branched Polypropylene
por: Stanic, Sascha, et al.
Publicado: (2021)

Directional Migration and Distribution of Magnetic Microparticles in Polypropylene-Matrix Magnetic Composites Molded by an Injection Molding Assisted by External Magnetic Field
por: Gu, Hang, et al.
Publicado: (2022)

Effect of Gas Counter Pressure on the Surface Roughness, Morphology, and Tensile Strength between Microcellular and Conventional Injection-Molded PP Parts
por: Ren, Jianping, et al.
Publicado: (2022)

A Combined In-Mold Decoration and Microcellular Injection Molding Method for Preparing Foamed Products with Improved Surface Appearance
por: Guo, Wei, et al.
Publicado: (2019)

Study on Foaming Quality and Impact Property of Foamed Polypropylene Composites
por: Gong, Wei, et al.
Publicado: (2018)

Crushing Responses of Expanded Polypropylene Foam
por: Xing, Yueqing, et al.
Publicado: (2023)

Effect of chemical treatments on properties of injection molded Nypa fruticans fiber reinforced polypropylene composite
por: Hasan, Afnan, et al.
Publicado: (2022)

Effect of Aluminum Flakes on Mechanical and Optical Properties of Foam Injection Molded Parts
por: Kim, Donghwi, et al.
Publicado: (2021)

Injection Molded PP Foams Using Food Ingredients for Food Packaging Applications
por: Tsagdi, Artemis, et al.
Publicado: (2021)

Morphological, thermal and mechanical properties of recycled HDPE foams via rotational molding
por: Dou, Yao, et al.
Publicado: (2021)

The Injected Foaming Study of Polypropylene/Multiwall Carbon Nanotube Composite with In Situ Fibrillation Reinforcement
por: Li, Gang, et al.
Publicado: (2022)

Using P(Pressure)-T(Temperature) Path to Control the Foaming Cell Sizes in Microcellular Injection Molding Process
por: Chen, Shia-Chung, et al.
Publicado: (2021)

Synergistic lignin construction of a long-chain branched polypropylene and its properties
por: Tian, Bo, et al.
Publicado: (2020)

Influence of Heat Sink on the Mold Temperature of Gypsum Mold Used in Injection Molding
por: Lin, Chung-Chih, et al.
Publicado: (2020)

A Design of Experiment Approach for Surface Roughness Comparisons of Foam Injection-Moulding Methods
por: Llewelyn, Gethin, et al.
Publicado: (2020)

Investigation on Foamed PP/Nano-CaCO(3) Composites in a Combined in-Mold Decoration and Microcellular Injection Molding Process
por: Yan, Kui, et al.
Publicado: (2020)

Cannot write session to /tmp/vufind_sessions/sess_5v6rmt0mljgpancb1q11p5asi5