Cargando…

Experimental Analysis of Kerf Taper Angle in Cutting Process of Sugar Palm Fiber Reinforced Unsaturated Polyester Composites with Laser Beam and Abrasive Water Jet Cutting Technologies

In this research, the effect of processing input parameters on the kerf taper angle response of three various material thicknesses of sugar palm fiber reinforced unsaturated polyester composite was investigated as an output parameter from abrasive waterjet and laser beam cutting techniques. The main...

Descripción completa

Detalles Bibliográficos
Autores principales:	Masoud, Fathi, Sapuan, S. M., Ariffin, Mohd Khairol Anuar Mohd, Nukman, Y., Bayraktar, Emin
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2021
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC8348318/ https://www.ncbi.nlm.nih.gov/pubmed/34372145 http://dx.doi.org/10.3390/polym13152543

Ejemplares similares

Experimental Analysis of Heat-Affected Zone (HAZ) in Laser Cutting of Sugar Palm Fiber Reinforced Unsaturated Polyester Composites
por: Masoud, Fathi, et al.
Publicado: (2021)

Cutting Processes of Natural Fiber-Reinforced Polymer Composites
por: Masoud, Fathi, et al.
Publicado: (2020)

Analysis of Kerf Quality Characteristics of Kevlar Fiber-Reinforced Polymers Cut by Abrasive Water Jet
por: Gubencu, Dinu-Valentin, et al.
Publicado: (2023)

Influence of Variable Radius of Cutting Head Trajectory on Quality of Cutting Kerf in the Abrasive Water Jet Process for Soda–Lime Glass
por: Sutowska, Marzena, et al.
Publicado: (2020)

Modelling the Kerf Angle, Roughness and Waviness of the Surface of Inconel 718 in an Abrasive Water Jet Cutting Process
por: Płodzień, Marcin, et al.
Publicado: (2023)

Kerf Taper Defect Minimization Based on Abrasive Waterjet Machining of Low Thickness Thermoplastic Carbon Fiber Composites C/TPU
por: Sambruno, Alejandro, et al.
Publicado: (2019)

Basics of cutting and abrasive processes
por: Toenshoff, Hans Kurt, et al.
Publicado: (2013)

Factorial Analysis of Fiber Laser Fusion Cutting of AISI 304 Stainless Steel: Evaluation of Effects on Process Performance, Kerf Geometry and Cut Edge Roughness
por: Mahrle, Achim, et al.
Publicado: (2021)

The Effects of Combined Infill Patterns on Mechanical Properties in FDM Process
por: Lalegani Dezaki, Mohammadreza, et al.
Publicado: (2020)

The Hyperbranched Polyester Reinforced Unsaturated Polyester Resin
por: Feng, Lifei, et al.
Publicado: (2022)

Prediction of Kerf Width and Surface Roughness of Al6351 Based Composite in Wire-Cut Electric Discharge Machining Using Mathematical Modelling
por: Sree Ram, Hariharan, et al.
Publicado: (2022)

Abrasive Waterjet (AWJ) Forces—Indicator of Cutting System Malfunction
por: Hlaváč, Libor M., et al.
Publicado: (2021)

Revised Model of Abrasive Water Jet Cutting for Industrial Use
por: Hlaváč, Libor M.
Publicado: (2021)

An investigation into the cutting efficiency of a novel degradable glass as an alternative to alumina powder in air abrasion cutting of enamel
por: Kotsanidou, Zoi, et al.
Publicado: (2021)

Mathematical Modeling and Experimental Study of Cutting Force for Cutting Hard and Brittle Materials in Fixed Abrasive Trepanning Drill
por: Yu, Ruijiang, et al.
Publicado: (2023)

Mechanical Properties of PALF/Kevlar-Reinforced Unsaturated Polyester Hybrid Composite Laminates
por: Bakhori, Siti Nadia Mohd, et al.
Publicado: (2022)

Effects of CNC Machining on Surface Roughness in Fused Deposition Modelling (FDM) Products
por: Lalegani Dezaki, Mohammadreza, et al.
Publicado: (2020)

Influence of air abrasion tips and operation modes on enamel-cutting characteristics
por: Peruchi, Cláudia, et al.
Publicado: (2013)

Cutting efficiency of different dental materials utilized in an air abrasion system
por: Hassan, Umair, et al.
Publicado: (2017)

Efficiency of Tool Steel Cutting by Water Jet with Recycled Abrasive Materials
por: Perec, Andrzej, et al.
Publicado: (2022)

Sequential Smoothing Treatment of Glass Workpieces Cut by Abrasive Water Jet
por: Sutowska, Marzena, et al.
Publicado: (2022)

Effect of silicon carbide on kerf convergence and irregularity of the surface during abrasive water jet machining of fiber-metal hybrid composites
por: Selvam, R., et al.
Publicado: (2023)

Influence of reduced graphene oxide addition on kerf width in abrasive water jet machining of nanofiller added epoxy-glass fibre composite
por: V., Kavimani, et al.
Publicado: (2022)

Location of the Cut Flexor Tendons in the Palm Using Surface Anatomy: A Simple Guide for Minimal Incision Surgery
por: Fathi, Afshin
Publicado: (2020)

Study of Effect of Impacting Direction on Abrasive Nanometric Cutting Process with Molecular Dynamics
por: Li, Junye, et al.
Publicado: (2018)

Cutting Performance of Randomly Distributed Active Abrasive Grains in Gear Honing Process
por: Gao, Yang, et al.
Publicado: (2021)

Estimation of Drag Finishing Abrasive Effect for Cutting Edge Preparation in Broaching Tool
por: Pérez-Salinas, Cristian F., et al.
Publicado: (2022)

Thermal Stability and Dynamic Mechanical Analysis of Benzoylation Treated Sugar Palm/Kenaf Fiber Reinforced Polypropylene Hybrid Composites
por: Mohd Izwan, S., et al.
Publicado: (2021)

Assessment of the Influence of Selected Technological Parameters on the Morphology Parameters of the Cutting Surfaces of the Hardox 500 Material Cut by Abrasive Water Jet Technology
por: Krenicky, Tibor, et al.
Publicado: (2022)

Statistical analysis of kerf mark measurements in bone
por: Bailey, James A., et al.
Publicado: (2010)

Prediction of Surface Roughness of an Abrasive Water Jet Cut Using an Artificial Neural Network
por: Ficko, Mirko, et al.
Publicado: (2021)

Reduction of Cracks in Marble Appeared at Hydro-Abrasive Jet Cutting Using Taguchi Method
por: Barabas, Sorin, et al.
Publicado: (2022)

Mechanical Properties of Longitudinal Basalt/Woven-Glass-Fiber-reinforced Unsaturated Polyester-Resin Hybrid Composites
por: Sapuan, S.M., et al.
Publicado: (2020)

Comparing the Air Abrasion Cutting Efficacy of Dentine Using a Fluoride-Containing Bioactive Glass versus an Alumina Abrasive: An In Vitro Study
por: Tan, Melissa H. X., et al.
Publicado: (2015)

Analysis of Several Physical Phenomena Measured on the Metallic Materials Cut by Abrasive Water Jets (AWJ)
por: Gřunděl, Jakub, et al.
Publicado: (2022)

Effect of Coating Thickness on Abrasion and Cutting Performance of NCD-Coated Ball Endmills on Graphite Machining
por: Lee, Hyeonhwa, et al.
Publicado: (2023)

Dynamic Mechanical Properties and Thermal Properties of Longitudinal Basalt/Woven Glass Fiber Reinforced Unsaturated Polyester Hybrid Composites
por: Haris, Nur Izzah Nabilah, et al.
Publicado: (2021)

Magnetic Abrasive Machining of Difficult-to-Cut Materials for Ultra-High-Speed Machining of AISI 304 Bars
por: Wang, Rui, et al.
Publicado: (2017)

Fixed-Diamond Abrasive Wire-Saw Cutting Force Modeling Based on Changes in Contact Arc Lengths
por: Liang, Lie, et al.
Publicado: (2023)

Highly Branched Bio-Based Unsaturated Polyesters by Enzymatic Polymerization
por: Nguyen, Hiep Dinh, et al.
Publicado: (2016)

Cannot write session to /tmp/vufind_sessions/sess_dcgt8hmqgsiqo1ahqrtp4ubq50