Cargando…

3D Printing of Fiber-Reinforced Plastic Composites Using Fused Deposition Modeling: A Status Review

Composite materials are a combination of two or more types of materials used to enhance the mechanical and structural properties of engineering products. When fibers are mixed in the polymeric matrix, the composite material is known as fiber-reinforced polymer (FRP). FRP materials are widely used in...

Descripción completa

Detalles Bibliográficos
Autores principales:	Pervaiz, Salman, Qureshi, Taimur Ali, Kashwani, Ghanim, Kannan, Sathish
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2021
Materias:	Review
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC8399339/ https://www.ncbi.nlm.nih.gov/pubmed/34443044 http://dx.doi.org/10.3390/ma14164520

Ejemplares similares

3D-Printed Fiber-Reinforced Polymer Composites by Fused Deposition Modelling (FDM): Fiber Length and Fiber Implementation Techniques
por: Ismail, Khairul Izwan, et al.
Publicado: (2022)

Fused-Deposition Modeling 3D Printing of Short-Cut Carbon-Fiber-Reinforced PA6 Composites for Strengthening, Toughening, and Light Weighting
por: Sun, Bin, et al.
Publicado: (2023)

Elasto-Plastic Mechanical Modeling of Fused Deposition 3D Printing Materials
por: Bandinelli, Francesco, et al.
Publicado: (2023)

Continuous Fiber-Reinforced Aramid/PETG 3D-Printed Composites with High Fiber Loading through Fused Filament Fabrication
por: Rijckaert, Sander, et al.
Publicado: (2022)

Rheological and Morphological Properties of Oil Palm Fiber-Reinforced Thermoplastic Composites for Fused Deposition Modeling (FDM)
por: Ahmad, Mohd Nazri, et al.
Publicado: (2021)

Microstructural Characterization and Property of Carbon Fiber Reinforced High-Density Polyethylene Composites Fabricated by Fused Deposition Modeling
por: Pandit, Partha Pratim, et al.
Publicado: (2022)

Development and Mechanical Characterization of Short Curauá Fiber-Reinforced PLA Composites Made via Fused Deposition Modeling
por: Cavalcanti, Daniel K. K., et al.
Publicado: (2022)

Calculating Filament Feed in the Fused Deposition Modeling Process to Correctly Print Continuous Fiber Composites in Curved Paths
por: Akhoundi, Behnam, et al.
Publicado: (2020)

Research Status of and Prospects for 3D Printing for Continuous Fiber-Reinforced Thermoplastic Composites
por: Yang, Yuan, et al.
Publicado: (2023)

Experimental investigation on fatigue life and tensile strength of carbon fiber-reinforced PLA composites based on fused deposition modeling
por: Kargar, Ehsan, et al.
Publicado: (2023)

Fabrication of Composite Filaments with High Dielectric Permittivity for Fused Deposition 3D Printing
por: Wu, Yingwei, et al.
Publicado: (2017)

Fused Filament Fabricated Polypropylene Composite Reinforced by Aligned Glass Fibers
por: Shulga, Eugene, et al.
Publicado: (2020)

Morphology and Mechanical Properties of 3D Printed Wood Fiber/Polylactic Acid Composite Parts Using Fused Deposition Modeling (FDM): The Effects of Printing Speed
por: Yang, Teng-Chun, et al.
Publicado: (2020)

Performance of 3D-Printed Continuous-Carbon-Fiber-Reinforced Plastics with Pressure
por: Zhang, Jun, et al.
Publicado: (2020)

Ultrasonic fatigue analysis of 3D-printed carbon fiber reinforced plastic
por: Jung, Chang-ho, et al.
Publicado: (2022)

Mechanical and Physical Properties of Recycled-Carbon-Fiber-Reinforced Polylactide Fused Deposition Modelling Filament
por: Omar, Nur’ain Wahidah Ya, et al.
Publicado: (2021)

Application of Taguchi Method to Optimize the Parameter of Fused Deposition Modeling (FDM) Using Oil Palm Fiber Reinforced Thermoplastic Composites
por: Ahmad, Mohd Nazri, et al.
Publicado: (2022)

Strengthening of 3D Printed Fused Deposition Manufactured Parts Using the Fill Compositing Technique
por: Belter, Joseph T., et al.
Publicado: (2015)

Development and Characterization of PBSA-Based Green Composites in 3D-Printing by Fused Deposition Modelling
por: Niang, Babacar, et al.
Publicado: (2022)

3D Printing of Fibre-Reinforced Thermoplastic Composites Using Fused Filament Fabrication—A Review
por: Dickson, Andrew N., et al.
Publicado: (2020)

Progress of Polymer-Based Dielectric Composites Prepared Using Fused Deposition Modeling 3D Printing
por: Hu, Xueling, et al.
Publicado: (2023)

Numerical Simulations of Components Produced by Fused Deposition 3D Printing
por: Scapin, Martina, et al.
Publicado: (2021)

Tensile Properties of Composite Reinforced with Three-Dimensional Printed Fibers
por: Agarwal, Komal, et al.
Publicado: (2020)

Impact Resistance of 3D-Printed Continuous Hybrid Fiber-Reinforced Composites
por: Akmal Zia, Ali, et al.
Publicado: (2023)

Structural Behavior of a Composite Curtain Wall Fabricated by the Fused Deposition Modeling 3D Printing Method
por: Park, Min Jae, et al.
Publicado: (2022)

Effect of Extrusion Temperature on the Physico-Mechanical Properties of Unidirectional Wood Fiber-Reinforced Polylactic Acid Composite (WFRPC) Components Using Fused Deposition Modeling
por: Yang, Teng-Chun
Publicado: (2018)

Coupling of Fused Deposition Modeling and Inkjet Printing to Produce Drug Loaded 3D Printed Tablets
por: Junqueira, Laura Andrade, et al.
Publicado: (2022)

Potential for Natural Fiber Reinforcement in PLA Polymer Filaments for Fused Deposition Modeling (FDM) Additive Manufacturing: A Review
por: Lee, Ching Hao, et al.
Publicado: (2021)

Research on the Simulation Model of Continuous Fiber-Reinforced Composites Printing Track
por: Wang, Yesong, et al.
Publicado: (2022)

Reducing Surface Roughness of 3D Printed Short-Carbon Fiber Reinforced Composites
por: Maier, Raluca, et al.
Publicado: (2022)

Optimization of Cutting Process Parameters in Inclined Drilling of Inconel 718 Using Finite Element Method and Taguchi Analysis
por: Pervaiz, Salman, et al.
Publicado: (2020)

Use of Biomaterials for 3D Printing by Fused Deposition Modeling Technique: A Review
por: Wasti, Sanjita, et al.
Publicado: (2020)

Orientation Planning in the Fused Deposition Modeling 3D Printing of Anatomical Spine Models
por: Damon, Aaron, et al.
Publicado: (2020)

Biodegradable Poly(Lactic Acid) Nanocomposites for Fused Deposition Modeling 3D Printing
por: Bardot, Madison, et al.
Publicado: (2020)

Fused Deposition Modeling 3D Printing in Oral and Maxillofacial Surgery: Problems and Solutions
por: Kamio, Takashi, et al.
Publicado: (2022)

Modification of Commercial 3D Fused Deposition Modeling Printer for Extrusion Printing of Hydrogels
por: Koltsov, Semyon I., et al.
Publicado: (2022)

3D Printed Fused Deposition Modeling (FDM) Capillaries for Chemiresistive Gas Sensors
por: Adamek, Martin, et al.
Publicado: (2023)

Production and Assessment of Poly(Lactic Acid) Matrix Composites Reinforced with Regenerated Cellulose Fibres for Fused Deposition Modelling
por: Gauss, Christian, et al.
Publicado: (2022)

Effect of Printing Parameters on Mechanical Behaviour of PLA-Flax Printed Structures by Fused Deposition Modelling
por: Belarbi, Yassine Elias, et al.
Publicado: (2021)

Comprehensive Characterization of Polymeric Composites Reinforced with Silica Microparticles Using Leftover Materials of Fused Filament Fabrication 3D Printing
por: Ahmed, Waleed, et al.
Publicado: (2021)

Cannot write session to /tmp/vufind_sessions/sess_8da1bjrua1fv93i2fhboho02vm