Cargando…

Experimental and Numerical Investigations of Titanium Deposition for Cold Spray Additive Manufacturing as a Function of Standoff Distance

In this research, the cold spray process as an additive manufacturing method was applied to deposit thick titanium coatings onto 7075 aluminium alloy. An analysis of changes in the microstructure and mechanical properties of the coatings depending on the standoff distance was carried out to obtain t...

Descripción completa

Detalles Bibliográficos
Autores principales:	Żórawski, Wojciech, Molak, Rafał, Mądry, Janusz, Sienicki, Jarosław, Góral, Anna, Makrenek, Medard, Scendo, Mieczysław, Dobosz, Romuald
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2021
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC8509138/ https://www.ncbi.nlm.nih.gov/pubmed/34639890 http://dx.doi.org/10.3390/ma14195492

Ejemplares similares

Influence of Surface Preparation on the Microstructure and Mechanical Properties of Cold-Sprayed Nickel Coatings on Al 7075 Alloy
por: Żórawski, Wojciech, et al.
Publicado: (2023)

Optimization of Mechanical Properties of Cr(3)C(2)-Ni20Cr/Graphite Cold Sprayed Coatings
por: Żórawski, Wojciech, et al.
Publicado: (2021)

Properties of Cold Sprayed Titanium and Titanium Alloy Coatings after Laser Surface Treatment
por: Zybała, Rafał, et al.
Publicado: (2022)

Influence of Laser Treatment on the Corrosion Resistance of Cr(3)C(2)-25(Ni20Cr) Cermet Coating
por: Scendo, Mieczyslaw, et al.
Publicado: (2021)

A Comparative Study of Aluminium and Titanium Warm Sprayed Coatings on AZ91E Magnesium Alloy
por: Molak, Rafał Maksymilian, et al.
Publicado: (2022)

Experimental and Numerical Study of Al2219 Powders Deposition on Al2219-T6 Substrate by Cold Spray: Effects of Spray Angle, Traverse Speed, and Standoff Distance
por: Zhang, Zheng, et al.
Publicado: (2023)

Standoff Distance in Ultrasonic Pulsating Water Jet
por: Srivastava, Madhulika, et al.
Publicado: (2020)

The effect of standoff distance and surface roughness on biofilm disruption using cavitation
por: Vyas, N., et al.
Publicado: (2020)

Standoff pump-probe photothermal detection of hazardous chemicals
por: Sharma, Ramesh C., et al.
Publicado: (2020)

The Effect of the Substrate on the Microstructure and Tribological Properties of Cold Sprayed (Cr(3)C(2)-25(Ni20Cr))-(Ni-graphite) Cermet Coatings
por: Trelka, Anna, et al.
Publicado: (2022)

India–China border standoff raises concerns on drug supplies
por: Sharma, Dinesh C
Publicado: (2020)

Insulating Material Development for the Design of Standoff Insulators Fed by Hybrid Voltage
por: Montanari, Gian Carlo, et al.
Publicado: (2022)

Standoff detection of bacterial spores by field deployable coherent Raman spectroscopy
por: Coluccelli, Nicola, et al.
Publicado: (2023)

Titanium matrix composites reinforced with biogenic filler
por: Zglobicka, Izabela, et al.
Publicado: (2022)

Effect of Temperature on Anti-Corrosive Properties of Diamond-Like Carbon Coating on S355 Steel
por: Scendo, Mieczyslaw, et al.
Publicado: (2019)

Titanium Plasma-Sprayed Coatings on Polymers for Hard Tissue Applications
por: Wypych, Artur, et al.
Publicado: (2018)

The Effects of Scanning Speed and Standoff Distance of the Fiber on Dusting Efficiency during Short Pulse Holmium: YAG Laser Lithotripsy
por: Chen, Junqin, et al.
Publicado: (2022)

Probe Standoff Optimization Method for Phased Array Ultrasonic TFM Imaging of Curved Parts
por: Mansur Rodrigues Filho, Jorge Franklin, et al.
Publicado: (2021)

Standoff Detection of Uranium and its Isotopes by Femtosecond Filament Laser Ablation Molecular Isotopic Spectrometry
por: Hartig, Kyle C., et al.
Publicado: (2017)

Multispectral LIF-Based Standoff Detection System for the Classification of CBE Hazards by Spectral and Temporal Features
por: Fellner, Lea, et al.
Publicado: (2020)

A study of potential laser-induced degradation in remote standoff Raman spectroscopy for wall paintings
por: Li, Yu, et al.
Publicado: (2022)

Effect of using different U/S probe Standoff materials in image geometry for interventional procedures: the example of prostate
por: Diamantopoulos, Stefanos, et al.
Publicado: (2011)

Standoff Detection and Identification of Liquid Chemicals on a Reflective Substrate Using a Wavelength-Tunable Quantum Cascade Laser
por: Park, Seongjin, et al.
Publicado: (2022)

Detonation Spraying of Hydroxyapatite on a Titanium Alloy Implant
por: Bulina, Natalia V., et al.
Publicado: (2021)

Standoff detection of biological agents using laser induced fluorescence—a comparison of 294 nm and 355 nm excitation wavelengths
por: Farsund, Øystein, et al.
Publicado: (2012)

Does standoff material affect acoustic radiation force impulse elastography? A preclinical study of a modified elastography phantom
por: Hollerieth, Katharina, et al.
Publicado: (2018)

Dual mode standoff imaging spectroscopy documents the painting process of the Lamb of God in the Ghent Altarpiece by J. and H. Van Eyck
por: Van der Snickt, Geert, et al.
Publicado: (2020)

Dissimilar Materials Welding with a Standoff-Free Vaporizing Foil Actuator between TRIP 1180 Steel Sheets and AA5052 Alloy
por: Jeong, Yuhyeong, et al.
Publicado: (2021)

Numerical evaluation of spray position for improved nasal drug delivery
por: Basu, Saikat, et al.
Publicado: (2020)

Preliminary analysis on the MD-4(®) plasma-sprayed titanium acetabular component()
por: de Araújo Loures, Elmano, et al.
Publicado: (2015)

Cold Gas Spraying of Nickel-Titanium Coatings for Protection Against Cavitation
por: Mauer, Georg, et al.
Publicado: (2020)

The Numerical Fatigue Life Analysis of a Conformal HPDC Mould Core Additively Manufactured from Maraging Steel
por: Piekło, Jarosław, et al.
Publicado: (2022)

Neural Network Modelling of Track Profile in Cold Spray Additive Manufacturing
por: Ikeuchi, Daiki, et al.
Publicado: (2019)

Experimental and numerical investigations on spray characteristics of fatty acid methyl esters
por: Lanjekar, R. D., et al.
Publicado: (2018)

Numerical Simulation and Experimental Study for the Impact of In-Flow Nozzle on Spray Characteristics
por: Mohamed, Mahmoud Abd El-Aziz, et al.
Publicado: (2021)

Biocompatibility of Advanced Manufactured Titanium Implants—A Review
por: Sidambe, Alfred T.
Publicado: (2014)

Functionality-packed additively manufactured porous titanium implants
por: van Hengel, I.A.J., et al.
Publicado: (2020)

Smartphone standoff: a qualitative study exploring clinician responses when a patient uses a smartphone to record a hospital clinical encounter
por: Ryan, Laura, et al.
Publicado: (2022)

Novel Approach in the Use of Plasma Spray: Preparation of Bulk Titanium for Bone Augmentations
por: Fousova, Michaela, et al.
Publicado: (2017)

Perspectives on Developing Burn Resistant Titanium Based Coatings—An Opportunity for Cold Spraying
por: Liang, Sihan, et al.
Publicado: (2023)

Cannot write session to /tmp/vufind_sessions/sess_6cjt1kbsn2p7172ov5v0e7ndoa