Cargando…

Effect of Sandblasting on Static and Fatigue Strength of Flash Butt Welded 75Cr4 Bandsaw Blades

The aim of the research presented in this article is analysis of the effect of the surface treatment method on the static and fatigue strength of flash butt welded bandsaw blades. A 1-mm-thick 75Cr1 cold-work tool steel sheet used for bandsaw blades was used as the test material. Fractographic studi...

Descripción completa

Detalles Bibliográficos
Autores principales:	Kubit, Andrzej, Lenart, Łukasz, Trzepieciński, Tomasz, Krzysiak, Andrzej, Łabuński, Wojciech
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2021
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC8619906/ https://www.ncbi.nlm.nih.gov/pubmed/34832232 http://dx.doi.org/10.3390/ma14226831

Ejemplares similares

Static and Dynamic Properties of Al-Mg Alloys Subjected to Hydrostatic Extrusion
por: Jurczak, Wojciech, et al.
Publicado: (2022)

Experimental and Numerical Investigations of Thin-Walled Stringer-Stiffened Panels Welded with RFSSW Technology under Uniaxial Compression
por: Kubit, Andrzej, et al.
Publicado: (2019)

Multi-Criteria Optimisation of Friction Stir Welding Parameters for EN AW-2024-T3 Aluminium Alloy Joints
por: Kubit, Andrzej, et al.
Publicado: (2022)

The Effect of Shot Peening on Residual Stress and Surface Roughness of AMS 5504 Stainless Steel Joints Welded Using the TIG Method
por: Bucior, Magdalena, et al.
Publicado: (2022)

Physical Simulation and Numerical Simulation of Flash Butt Welding for Innovative Dual Phase Steel DP590: A Comparative Study
por: Song, Jingwen, et al.
Publicado: (2023)

The Effect of Weld Reinforcement and Post-Welding Cooling Cycles on Fatigue Strength of Butt-Welded Joints under Cyclic Tensile Loading
por: Araque, Oscar, et al.
Publicado: (2018)

Manufacturing Parameters, Materials, and Welds Properties of Butt Friction Stir Welded Joints–Overview
por: Laska, Aleksandra, et al.
Publicado: (2020)

Prediction and Characteristics of Angular Distortion in Multi-Layer Butt Welding
por: Seong, Woo-Jae
Publicado: (2019)

Computational modeling of fatigue crack propagation in butt welded joints subjected to axial load
por: Araque, Oscar, et al.
Publicado: (2019)

Parametric Formulae for Elastic Stress Concentration Factor at the Weld Toe of Distorted Butt-Welded Joints
por: Luo, Yuxiao, et al.
Publicado: (2020)

Surface Finish Analysis in Single Point Incremental Sheet Forming of Rib-Stiffened 2024-T3 and 7075-T6 Alclad Aluminium Alloy Panels
por: Trzepieciński, Tomasz, et al.
Publicado: (2021)

An Experimental Study of the Frictional Properties of Steel Sheets Using the Drawbead Simulator Test
por: Trzepiecinski, Tomasz, et al.
Publicado: (2019)

Three-Dimensional Smooth Particle Hydrodynamics Modeling and Experimental Analysis of the Ballistic Performance of Steel-Based FML Targets
por: Kubit, Andrzej, et al.
Publicado: (2022)

Influence of Interlayer Temperature and Welding Sequence on the Temperature Distribution and Welding Residual Stress of the Saddle-Shaped Joint of Weldolet-Header Butt Welding
por: Mai, Chunliang, et al.
Publicado: (2021)

Assessment of the Effect of Laser Welding on the Properties and Structure of TMCP Steel Butt Joints
por: Górka, Jacek
Publicado: (2020)

Rapid Calculation of Residual Stresses in Dissimilar S355–AA6082 Butt Welds
por: Leoni, Francesco, et al.
Publicado: (2021)

The effect of TIG welding on the structure and hardness of butt joints made of Inconel 718
por: Górka, Jacek, et al.
Publicado: (2023)

Laser-CMT Hybrid Welding-Brazing of Al/Steel Butt Joint: Weld Formation, Intermetallic Compounds, and Mechanical Properties
por: Chen, Yuxin, et al.
Publicado: (2019)

Strength Analysis of a Rib-Stiffened GLARE-Based Thin-Walled Structure
por: Kubit, Andrzej, et al.
Publicado: (2020)

Ultimate Load-Carrying Ability of Rib-Stiffened 2024-T3 and 7075-T6 Aluminium Alloy Panels under Axial Compression
por: Slota, Ján, et al.
Publicado: (2021)

Investigation into the Effect of RFSSW Parameters on Tensile Shear Fracture Load of 7075-T6 Alclad Aluminium Alloy Joints
por: Kubit, Andrzej, et al.
Publicado: (2021)

A Precise Visual Method for Narrow Butt Detection in Specular Reflection Workpiece Welding
por: Zeng, Jinle, et al.
Publicado: (2016)

Stress Concentration Factors for Butt-Welded Plates Subjected to Tensile, Bending and Shearing Loads
por: Molski, Krzysztof L., et al.
Publicado: (2020)

Critical Review on Magnetically Impelled Arc Butt Welding: Challenges, Perspectives and Industrial Applications
por: Chaturvedi, Mukti, et al.
Publicado: (2023)

Effect of Welding Parameters on Mechanical Properties and Microstructure of Friction Stir Welded AA7075-T651 Aluminum Alloy Butt Joints
por: Kosturek, Robert, et al.
Publicado: (2022)

Effect of Shot Peening on the Low-Cycle Fatigue Behavior of an AA2519-T62 Friction-Stir-Welded Butt Joint
por: Kosturek, Robert, et al.
Publicado: (2023)

The Study on Mechanical Strength of Titanium-Aluminum Dissimilar Butt Joints by Laser Welding-Brazing Process
por: Zhou, Xiongfeng, et al.
Publicado: (2019)

Microstructure and Mechanical Properties of Friction Stir Welded 2205 Duplex Stainless Steel Butt Joints
por: Ahmed, Mohamed M. Z., et al.
Publicado: (2021)

Effect of Butt Gap on Stress Distribution and Carrying Capacity of X80 Pipeline Girth Weld
por: Zhu, Lixia, et al.
Publicado: (2022)

Comparative Study on Welding Characteristics of Laser-CMT and Plasma-CMT Hybrid Welded AA6082-T6 Aluminum Alloy Butt Joints
por: Xin, Zhibin, et al.
Publicado: (2019)

Friction Stir Welding of 2205 Duplex Stainless Steel: Feasibility of Butt Joint Groove Filling in Comparison to Gas Tungsten Arc Welding
por: Ahmed, Mohamed M. Z., et al.
Publicado: (2021)

The Effect of Novel Complex Treatment of Annealing and Sandblasting on the Microstructure and Performance of Welded TA1 Titanium Plate
por: Xu, Yanbin, et al.
Publicado: (2023)

Modelling of Friction Phenomena Existed in Drawbead in Sheet Metal Forming
por: Trzepieciński, Tomasz, et al.
Publicado: (2021)

A Vision-Aided 3D Path Teaching Method before Narrow Butt Joint Welding
por: Zeng, Jinle, et al.
Publicado: (2017)

Effects of Different Pre-Heating Welding Methods on the Temperature Field, Residual Stress and Deformation of a Q345C Steel Butt-Welded Joint
por: Yuan, Jie, et al.
Publicado: (2023)

Effects of Underwater Friction Stir Welding Heat Generation on Residual Stress of AA6068-T6 Aluminum Alloy
por: Khalaf, Hassanein I., et al.
Publicado: (2022)

Microstructure and Mechanical Properties of Solid-State Rotary Friction Welded Inconel 713C and 32CrMo4 Steel Joints Used in a Turbocharger Rotor
por: Szwajka, Krzysztof, et al.
Publicado: (2023)

Microstructure and Mechanical Properties of Al/Steel Butt Joint by Hybrid CMT Welding with External Axial Magnetic Field
por: Kang, Kexin, et al.
Publicado: (2020)

Improving the Quality of Dissimilar Al/Steel Butt-Lap Joint via Ultrasonic-Assisted Friction Stir Welding
por: Chen, Yu, et al.
Publicado: (2022)

George Berkeley Butt
Publicado: (1902)

Cannot write session to /tmp/vufind_sessions/sess_315h942g85950ijmmn4m8rn97o