Cargando…

Experimental Study of Hardened Young’s Modulus for 3D Printed Mortar

Few studies have focused on determining the Young’s modulus of 3D printed structures. This study presents the results of experimental investigations of Young’s modulus of a 3D printed mortar. Specimens were prepared in four different ways to investigate possible application of different methods for...

Descripción completa

Detalles Bibliográficos
Autores principales:	Skibicki, Szymon, Techman, Mateusz, Federowicz, Karol, Olczyk, Norbert, Hoffmann, Marcin
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2021
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC8707079/ https://www.ncbi.nlm.nih.gov/pubmed/34947238 http://dx.doi.org/10.3390/ma14247643

Ejemplares similares

Automation in the Construction of a 3D-Printed Concrete Wall with the Use of a Lintel Gripper
por: Hoffmann, Marcin, et al.
Publicado: (2020)

Early-Age Mechanical Properties of 3D-Printed Mortar with Spent Garnet
por: Skibicki, Szymon, et al.
Publicado: (2021)

Mechanical Properties of Hardened 3D Printed Concretes and Mortars—Development of a Consistent Experimental Characterization Strategy
por: Meurer, Maximilian, et al.
Publicado: (2021)

Modification of Lightweight Aggregate Concretes with Silica Nanoparticles—A Review
por: Federowicz, Karol, et al.
Publicado: (2021)

Effect of Curing Methods on Shrinkage Development in 3D-Printed Concrete
por: Federowicz, Karol, et al.
Publicado: (2020)

Load-Bearing Capacity of Beams Reinforced with Composite Rebar in Regard to Existing Guidelines
por: Olczyk, Norbert, et al.
Publicado: (2021)

Experimental–Computational Investigation of the Elastic Modulus of Mortar under Sulfate Attack
por: Guan, Zhongzheng, et al.
Publicado: (2023)

Foundation Piles—A New Feature for Concrete 3D Printers
por: Hoffmann, Marcin, et al.
Publicado: (2021)

The E-modulus of the oocyte is a non-destructive measure of zona pellucida hardening
por: Schmitz, Carlo, et al.
Publicado: (2021)

Comparison of the Compression and Tensile Modulus of Two Chosen Resins Used in Dentistry for 3D Printing
por: Paradowska-Stolarz, Anna, et al.
Publicado: (2022)

A 3D-Printed Ultra-Low Young’s Modulus β-Ti Alloy for Biomedical Applications
por: Pellizzari, Massimo, et al.
Publicado: (2020)

Evaluation of the Mechanical Properties of a 3D-Printed Mortar
por: Lee, Hojae, et al.
Publicado: (2019)

Modulus adaptive lubricating prototype inspired by instant muscle hardening mechanism of catfish skin
por: Zhang, Yunlei, et al.
Publicado: (2022)

A Bi-Modulus Material Model for Bending Test on NHL3.5 Lime Mortar
por: Grazzini, Rebecca, et al.
Publicado: (2023)

Mechanical and Material Properties of Mortar Reinforced with Glass Fiber: An Experimental Study
por: Małek, Marcin, et al.
Publicado: (2021)

Effects of Nozzle Details on Print Quality and Hardened Properties of Underwater 3D Printed Concrete
por: Yang, Jun-Mo, et al.
Publicado: (2022)

Comparison of Properties of 3D-Printed Mortar in Air vs. Underwater
por: Woo, Seong-Jin, et al.
Publicado: (2021)

Interlayer Strength of 3D-Printed Mortar Reinforced by Postinstalled Reinforcement
por: Park, Jihun, et al.
Publicado: (2021)

A Novel Approach for 3D Printing Fiber-Reinforced Mortars
por: Ungureanu, Dragoș, et al.
Publicado: (2023)

The Influence of Density on the Value of Young’s Modulus for Dry Ice
por: Biszczanik, Aleksandra, et al.
Publicado: (2021)

Influence of Microfibrillated Cellulose Additive on Strength, Elastic Modulus, Heat Release, and Shrinkage of Mortar and Concrete
por: Barabanshchikov, Yurii, et al.
Publicado: (2021)

Effect of 3D Printed Spatial Reinforcement on Flexural Characteristics of Conventional Mortar
por: Katzer, Jacek, et al.
Publicado: (2020)

Properties of 3D-Printed Polymer Fiber-Reinforced Mortars: A Review
por: Liu, Jie, et al.
Publicado: (2022)

Influence of Silica Modulus and Curing Temperature on the Strength of Alkali-Activated Volcanic Ash and Limestone Powder Mortar
por: Adewumi, Adeshina Adewale, et al.
Publicado: (2021)

Restrained Stress Development in Hardening Mortar Internally Cured with Superabsorbent Polymers under Autogenous and Drying Conditions
por: Yeon, Jung Heum
Publicado: (2021)

Compressive and Shear Behavior of Masonry Reinforced with Ultra-Rapid-Hardening Fiber-Reinforced Mortar (URH-FRM)
por: Lee, Joo Ha
Publicado: (2022)

Effect of the Partial Replacement of Cement with Waste Granite Powder on the Properties of Fresh and Hardened Mortars for Masonry Applications
por: Woźniak, Zuzanna Zofia, et al.
Publicado: (2022)

The Effects of Temperature Curing on the Strength Development, Transport Properties, and Freeze-Thaw Resistance of Blast Furnace Slag Cement Mortars Modified with Nanosilica
por: Federowicz, Karol, et al.
Publicado: (2020)

Dynamic Properties and Fractal Characteristics of 3D Printed Cement Mortar in SHPB Test
por: Mo, Yixin, et al.
Publicado: (2021)

Developing and Testing of Strain-Hardening Cement-Based Composites (SHCC) in the Context of 3D-Printing
por: Ogura, Hiroki, et al.
Publicado: (2018)

Mechanical Behavior of Printed Strain Hardening Cementitious Composites
por: Chaves Figueiredo, Stefan, et al.
Publicado: (2020)

Data on effect of a reducer of water and retarder of setting time admixtures of cement pastes and mortar in hardened stat
por: Khudhair, Mohammed Husssein, et al.
Publicado: (2018)

Microstructure and Durability Performance of Mortars with Volcanic Powder from Calbuco Volcano (Chile) after 4 Hardening Years
por: Tremiño, Rosa María, et al.
Publicado: (2021)

The Influence of Mg-Impurities in Raw Materials on the Synthesis of Rankinite Clinker and the Strength of Mortar Hardening in CO(2) Environment
por: Siauciunas, Raimundas, et al.
Publicado: (2023)

Highly Integrated Elastic Island-Structured Printed Circuit Board with Controlled Young’s Modulus for Stretchable Electronics
por: Cho, Duho, et al.
Publicado: (2020)

Apparent Young’s Modulus of Epoxy Adhesives
por: Anasiewicz, Kamil, et al.
Publicado: (2022)

Determination of the Elasticity Modulus of 3D-Printed Octet-Truss Structures for Use in Porous Prosthesis Implants
por: Bagheri, Ali, et al.
Publicado: (2018)

Determination of Stiffness and the Elastic Modulus of 3D-Printed Micropillars with Atomic Force Microscopy–Force Spectroscopy
por: Cortelli, Giorgio, et al.
Publicado: (2023)

A Study into the Effect of Different Nozzles Shapes and Fibre-Reinforcement in 3D Printed Mortar
por: Shakor, Pshtiwan, et al.
Publicado: (2019)

Effect of Structural Build-Up on Interlayer Bond Strength of 3D Printed Cement Mortars
por: Pan, Tinghong, et al.
Publicado: (2021)

Cannot write session to /tmp/vufind_sessions/sess_c5n9sjd5nl1h5n2j7sa45erlhk