Cargando…

Effect of the Processing Parameters on the Porosity and Mechanical Behavior of Titanium Samples with Bimodal Microstructure Produced via Hot Pressing

Commercially pure (c.p.) titanium grade IV with a bimodal microstructure is a promising material for biomedical implants. The influence of the processing parameters on the physical, microstructural, and mechanical properties was investigated. The bimodal microstructure was achieved from the blends o...

Descripción completa

Detalles Bibliográficos
Autores principales:	Chávez-Vásconez, Ricardo, Lascano, Sheila, Sauceda, Sergio, Reyes-Valenzuela, Mauricio, Salvo, Christopher, Mangalaraja, Ramalinga Viswanathan, Gotor, Francisco José, Arévalo, Cristina, Torres, Yadir
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2021
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC8746005/ https://www.ncbi.nlm.nih.gov/pubmed/35009282 http://dx.doi.org/10.3390/ma15010136

Ejemplares similares

Influence of Sintering Temperature on the Microstructure and Mechanical Properties of In Situ Reinforced Titanium Composites by Inductive Hot Pressing
por: Arévalo, Cristina, et al.
Publicado: (2016)

Microstructure and Mechanical Properties of Graphene Oxide-Reinforced Titanium Matrix Composites Synthesized by Hot-Pressed Sintering
por: Liu, Jingqi, et al.
Publicado: (2019)

Fast Solution Synthesis of NiO-Gd(0.1)Ce(0.9)O(1.95) Nanocomposite via Different Approach: Influence of Processing Parameters and Characterizations
por: Durango-Petro, Jorge, et al.
Publicado: (2021)

Analysis of the Microstructure and Mechanical Properties of Titanium-Based Composites Reinforced by Secondary Phases and B(4)C Particles Produced via Direct Hot Pressing
por: Montealegre-Melendez, Isabel, et al.
Publicado: (2017)

Mechanical Properties and Microstructure of Hot-Pressed Silica Matrix Composites
por: Wang, Weili, et al.
Publicado: (2022)

Experimental Analysis of Porosity and Permeability in Pressed Paper
por: Park, Juhwan, et al.
Publicado: (2016)

Synthesis and Characterization of a Nearly Single Bulk Ti(2)AlN MAX Phase Obtained from Ti/AlN Powder Mixture through Spark Plasma Sintering
por: Salvo, Christopher, et al.
Publicado: (2021)

Mitigating Inhomogeneity and Tailoring the Microstructure of Selective Laser Melted Titanium Orthorhombic Alloy by Heat Treatment, Hot Isostatic Pressing, and Multiple Laser Exposures
por: Polozov, Igor, et al.
Publicado: (2021)

Effect of Hot Isostatic Pressing on Porosity and Mechanical Properties of 316 L Stainless Steel Prepared by the Selective Laser Melting Method
por: Cegan, Tomas, et al.
Publicado: (2020)

Highly sensitive and selective detection of glutathione using ultrasonic aided synthesis of graphene quantum dots embedded over amine-functionalized silica nanoparticles
por: Kaimal, Reshma, et al.
Publicado: (2021)

Optimization of Low-Cost Ti-35421 Titanium Alloy: Phase Transformation, Bimodal Microstructure, and Combinatorial Mechanical Properties
por: Chen, Fuwen, et al.
Publicado: (2019)

Improved Predictability of Microstructure Evolution during Hot Deformation of Titanium Alloys
por: Buzolin, Ricardo Henrique, et al.
Publicado: (2020)

Effect of Different Hot-Pressing Pressure and Temperature on the Performance of Titanium Mesh-Based MEA for DMFC
por: Wang, Xingxing, et al.
Publicado: (2022)

Permanent Porosity in Hydroxamate Titanium–Organic Polyhedra
por: Lerma-Berlanga, Belén, et al.
Publicado: (2021)

Microstructures and Properties of Porous Liquid-Phase-Sintered SiC Ceramic by Hot Press Sintering
por: Li, Yajie, et al.
Publicado: (2019)

Hard carbon microspheres with bimodal size distribution and hierarchical porosity via hydrothermal carbonization of trehalose
por: Wortmann, Martin, et al.
Publicado: (2023)

Fabrication and Characterization of Bioactive Gelatin–Alginate–Bioactive Glass Composite Coatings on Porous Titanium Substrates
por: Begines, Belen, et al.
Publicado: (2022)

Microstructure and Mechanical Properties of Laser Welded Al-Si Coated Hot-Press-Forming Steel Joints
por: Chen, Xi, et al.
Publicado: (2019)

Design and synthesis of heterocyclic azole based bioactive compounds: Molecular structures, quantum simulation, and mechanistic studies through docking as multi-target inhibitors of SARS-CoV-2 and cytotoxicity
por: Haribabu, Jebiti, et al.
Publicado: (2022)

Improved Corrosion Behavior and Biocompatibility of Porous Titanium Samples Coated with Bioactive Chitosan-Based Nanocomposites
por: García-Cabezón, Cristina, et al.
Publicado: (2021)

Effect of Heat Treatment Temperature on Microstructure and Properties of PM Borated Stainless Steel Prepared by Hot Isostatic Pressing
por: Pei, Yanbin, et al.
Publicado: (2021)

Microstructure and Thermal Deformation Behavior of Hot-Pressing Sintered Zr-6Al-0.1B Alloy
por: Yan, Huajun, et al.
Publicado: (2022)

Effect of Graphene Nanosheets Content on Microstructure and Mechanical Properties of Titanium Matrix Composite Produced by Cold Pressing and Sintering
por: Haghighi, Milad, et al.
Publicado: (2018)

Influence of Hot Rolling and Heat Treatment on the Microstructural Evolution of β20C Titanium Alloy
por: Liu, Xin, et al.
Publicado: (2017)

Image-based data on strain fields of microstructures with porosity defects
por: Khanolkar, Pranav, et al.
Publicado: (2020)

Microstructures and Properties of AlMgTi-Based Metal-Intermetallic Laminate Composites by Dual-Steps Vacuum Hot Pressing
por: Meng, Linggang, et al.
Publicado: (2020)

Influence of Infiltration Pressure on the Microstructure and Properties of 2D-CFRP Prepared by the Vacuum Infiltration Hot Pressing Molding Process
por: Ma, Yuqin, et al.
Publicado: (2019)

Microstructure and Mechanical Properties of Ni-20Cr-Eu(2)O(3) Composites Prepared by Vacuum Hot Pressing
por: Zhou, Yihong, et al.
Publicado: (2023)

Microstructure, Mechanical Properties and Oxidation Resistance of Nb-Si Based Ultrahigh-Temperature Alloys Prepared by Hot Press Sintering
por: Zhang, Lijing, et al.
Publicado: (2023)

Microstructure of TiAl Capsules Processed by Electron Beam Powder Bed Fusion Followed by Post-Hot Isostatic Pressing
por: Bakhshi Farkoush, Hanieh, et al.
Publicado: (2023)

Characterization and Monitoring of Titanium Bone Implants with Impedance Spectroscopy
por: Olmo, Alberto, et al.
Publicado: (2020)

The Influence of Porosity on Fatigue Crack Initiation in Additively Manufactured Titanium Components
por: Tammas-Williams, S., et al.
Publicado: (2017)

Effects of pore size and porosity on cytocompatibility and osteogenic differentiation of porous titanium
por: Yao, Yi-tong, et al.
Publicado: (2021)

Complementary Methods for the Assessment of the Porosity of Laser Additive-Manufactured Titanium Alloy
por: Petrișor, Silviu Mihai, et al.
Publicado: (2023)

Additive manufacturing titanium components with isotropic or graded properties by hybrid electron beam melting/hot isostatic pressing powder processing
por: Hernández-Nava, E., et al.
Publicado: (2019)

Study on the Hot Deformation Characterization of Borated Stainless Steel by Hot Isostatic Pressing
por: Pei, Yanbin, et al.
Publicado: (2021)

Nanocarrier of α-Tocopheryl Succinate Based on a Copolymer Derivative of (4,7-dichloroquinolin-2-yl)methanol and Its Cytotoxicity against a Breast Cancer Cell Line
por: Valle, Hernán, et al.
Publicado: (2023)

Effect of Heating on Hot Deformation and Microstructural Evolution of Ti-6Al-4V Titanium Alloy
por: Li, Dechong, et al.
Publicado: (2023)

Microstructures and Enhanced Mechanical Properties of (Zr, Ti)(C, N)-Based Nanocomposites Fabricated by Reactive Hot-Pressing at Low Temperature
por: Zhang, Mengmeng, et al.
Publicado: (2023)

Bimodal Porosity and Stability of a TiO(2) Gig-Lox Sponge Infiltrated with Methyl-Ammonium Lead Iodide Perovskite
por: Sanzaro, Salvatore, et al.
Publicado: (2019)

Cannot write session to /tmp/vufind_sessions/sess_7or0tt1guuh02vn7og4chaon2d