Cargando…

Effects of Injection Molding Parameters on Properties of Insert-Injection Molded Polypropylene Single-Polymer Composites

The reinforcement and matrix of a polymer material can be composited into a single polymer composite (SPC), which is light weight, high strength, and has easy recyclability. The insert injection molding process can be used to realize the multiple production of SPC products with a short cycle time an...

Descripción completa

Detalles Bibliográficos
Autores principales:	Wang, Jian, Mao, Qianchao, Jiang, Nannan, Chen, Jinnan
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2021
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC8747091/ https://www.ncbi.nlm.nih.gov/pubmed/35012046 http://dx.doi.org/10.3390/polym14010023

Ejemplares similares

Fabric Insert Injection Molding for the Preparation of Ultra-High Molecular Weight Polyethylene/High-Density Polyethylene Two-Component Self-Reinforced Composites
por: Wang, Jian, et al.
Publicado: (2022)

Post-Molding Shrinkage, Structure and Properties of Cellular Injection-Molded Polypropylene
por: Kościuszko, Artur, et al.
Publicado: (2022)

Effect of Rapid Mold Heating on the Structure and Performance of Injection-Molded Polypropylene
por: Liparoti, Sara, et al.
Publicado: (2020)

Modeling and Analysis of Morphology of Injection Molding Polypropylene Parts Induced by In-Mold Annealing
por: Salomone, Rita, et al.
Publicado: (2022)

Effects of Injection Molding Process Parameters on the Chemical Foaming Behavior of Polypropylene and Polystyrene
por: Chung, Chen-Yuan, et al.
Publicado: (2021)

Effect of chemical treatments on properties of injection molded Nypa fruticans fiber reinforced polypropylene composite
por: Hasan, Afnan, et al.
Publicado: (2022)

Direct In-Mold Impregnation of Glass Fiber Fabric by Polypropylene with Supercritical Nitrogen in Microcellular Injection Molding Process
por: He, Qichao, et al.
Publicado: (2023)

Mechanical Properties Distribution within Polypropylene Injection Molded Samples: Effect of Mold Temperature under Uneven Thermal Conditions
por: Liparoti, Sara, et al.
Publicado: (2017)

Post-Processing Time Dependence of Shrinkage and Mechanical Properties of Injection-Molded Polypropylene
por: Kościuszko, Artur, et al.
Publicado: (2020)

Injection Molded Novel Biocomposites from Polypropylene and Sustainable Biocarbon
por: Abdelwahab, Mohamed A., et al.
Publicado: (2019)

Insights on the Molecular Behavior of Polypropylene in the Process of Ultrasonic Injection Molding
por: Iturbe-Ek, Jackeline, et al.
Publicado: (2021)

Enhanced Injection Molding Simulation of Advanced Injection Molds
por: Zink, Béla, et al.
Publicado: (2017)

Directional Migration and Distribution of Magnetic Microparticles in Polypropylene-Matrix Magnetic Composites Molded by an Injection Molding Assisted by External Magnetic Field
por: Gu, Hang, et al.
Publicado: (2022)

The Cellular Structure and Mechanical Properties of Polypropylene/Nano-CaCO(3)/Ethylene-propylene-diene-monomer Composites Prepared by an In-Mold-Decoration/Microcellular-Injection-Molding Process
por: Zeng, Fankun, et al.
Publicado: (2023)

Investigation of Interface Thermal Resistance between Polymer and Mold Insert in Micro-Injection Molding by Non-Equilibrium Molecular Dynamics
por: Weng, Can, et al.
Publicado: (2020)

Injection Molding of Low-Density Polyethylene (LDPE) as a Model Polymer: Effect of Molding Parameters on the Microstructure and Crystallinity
por: Leyva-Porras, César, et al.
Publicado: (2021)

Manufacturing Signatures of Injection Molding and Injection Compression Molding for Micro-Structured Polymer Fresnel Lens Production
por: Loaldi, Dario, et al.
Publicado: (2018)

Injection-Molded Isotactic Polypropylene Colored with Green Transparent and Opaque Pigments
por: Janostik, Vaclav, et al.
Publicado: (2023)

Effects of Cavity Thickness and Mold Surface Roughness on the Polymer Flow during Micro Injection Molding
por: Li, Jiquan, et al.
Publicado: (2023)

Injection Molding and Mechanical Properties of Bio-Based Polymer Nanocomposites
por: Mistretta, Maria Chiara, et al.
Publicado: (2018)

Effect of Mold Temperature on the Impact Behavior and Morphology of Injection Molded Foams Based on Polypropylene Polyethylene–Octene Copolymer Blends
por: Muñoz-Pascual, Santiago, et al.
Publicado: (2019)

Pressure Analysis of Dynamic Injection Molding and Process Parameter Optimization for Reducing Warpage of Injection Molded Products
por: Wang, Xinyu, et al.
Publicado: (2017)

Effect of Compatibility on the Foaming Behavior of Injection Molded Polypropylene and Polycarbonate Blend Parts
por: Su, Bei, et al.
Publicado: (2019)

Interfacial Adhesion and Mechanical Properties of Wood-Polymer Hybrid Composites Prepared by Injection Molding
por: Stadlmann, Alexander, et al.
Publicado: (2021)

Influence of the Mold Material on the Injection Molding Cycle Time and Warpage Depending on the Polymer Processed
por: Lucyshyn, Thomas, et al.
Publicado: (2021)

Reducing the Burn Marks on Injection-Molded Parts by External Gas-Assisted Injection Molding
por: Li, Jiquan, et al.
Publicado: (2021)

Tomographic and Tension Analysis of Polypropylene Reinforced with Carbon Fiber Fabric by Injection Molding
por: Wieczorowski, Michal, et al.
Publicado: (2023)

Influence of Heat Sink on the Mold Temperature of Gypsum Mold Used in Injection Molding
por: Lin, Chung-Chih, et al.
Publicado: (2020)

Filling-Balance-Oriented Parameters for Multi-Cavity Molds in Polyvinyl Chloride Injection Molding
por: Tsai, Hsi-Hsun, et al.
Publicado: (2022)

Injection Molding of 3-3 Hydroxyapatite Composites
por: Biggemann, Jonas, et al.
Publicado: (2020)

Effect of the Process Parameters on the Adhesive Strength of Dissimilar Polymers Obtained by Multicomponent Injection Molding
por: Pisanu, Luciano, et al.
Publicado: (2021)

In-Mold Sensors for Injection Molding: On the Way to Industry 4.0
por: Ageyeva, Tatyana, et al.
Publicado: (2019)

Multiple In-Mold Sensors for Quality and Process Control in Injection Molding
por: Párizs, Richárd Dominik, et al.
Publicado: (2023)

Fabrication of Micro-Structured Polymer by Micro Injection Molding Based on Precise Micro-Ground Mold Core
por: Lu, Yanjun, et al.
Publicado: (2019)

Correlation between Scratch Behavior and Tensile Properties in Injection Molded and Extruded Polymers
por: Germann, Jasmina, et al.
Publicado: (2022)

Handbook of metal injection molding
por: Heaney, Donald F.
Publicado: (2012)

Thermoelasticity of Injection-Molded Parts
por: Turk, Janez, et al.
Publicado: (2023)

Mechanical Properties of Injection Molded PP/PET-Nanofibril Composites and Foams
por: Mark, Lun Howe, et al.
Publicado: (2022)

Studying nanostructure gradients in injection-molded polypropylene/montmorillonite composites by microbeam small-angle x-ray scattering
por: Stribeck, Norbert, et al.
Publicado: (2014)

Improvement in Injection Molding Quality Performance with Innovative Cyclone Mixers Used in Polypropylene with Spherical Silicon Dioxide Composites
por: Hu, Zhan-Xiang, et al.
Publicado: (2022)

Cannot write session to /tmp/vufind_sessions/sess_3kghs04qq4qmc9ov02t2cgrhkl