Cargando…

Effect of Fibre Orientation on Impact Damage Resistance of S2/FM94 Glass Fibre Composites for Aerospace Applications: An Experimental Evaluation and Numerical Validation

This study aims to investigate the influence of fibre orientation and varied incident energy levels on the impact-induced damage of S2/FM94, a kind of aerospace glass fibre epoxy/composite regularly used in aircraft components and often subjected to low-velocity impact loadings. Effects of varying p...

Descripción completa

Detalles Bibliográficos
Autores principales:	Giasin, Khaled, Dhakal, Hom N., Featheroson, Carol A., Pimenov, Danil Yurievich, Lupton, Colin, Jiang, Chulin, Barouni, Antigoni, Koklu, Ugur
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2021
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC8747735/ https://www.ncbi.nlm.nih.gov/pubmed/35012118 http://dx.doi.org/10.3390/polym14010095

Ejemplares similares

Three-Dimensional Finite Element Modeling of Drilling-Induced Damage in S2/FM94 Glass-Fiber-Reinforced Polymers (GFRPs)
por: Manzoor, Shahryar, et al.
Publicado: (2022)

Corrosion Behaviour of High-Strength Al 7005 Alloy and Its Composites Reinforced with Industrial Waste-Based Fly Ash and Glass Fibre: Comparison of Stir Cast and Extrusion Conditions
por: Swamy, Praveen Kumar, et al.
Publicado: (2021)

The Effect of Various Environmental Conditions on the Impact Damage Behaviour of Natural-Fibre-Reinforced Composites (NFRCs)—A Critical Review
por: Musthaq, Muneer Ahmed., et al.
Publicado: (2023)

Investigation of the Contact Interface between Natural Fibre Metal Laminates under Tension Using Finite Element Analysis (FEA)
por: Song, Chun Han, et al.
Publicado: (2022)

Evaluation of Cutting-Tool Coating on the Surface Roughness and Hole Dimensional Tolerances during Drilling of Al6061-T651 Alloy
por: Al-Tameemi, Hamza A., et al.
Publicado: (2021)

Improved mechanical performances of unidirectional jute fibre composites developed with new fibre architectures
por: Hasan, Mahmudul, et al.
Publicado: (2021)

Evaluation of the Mechanical Properties and Drilling of Glass Bead/Fiber-Reinforced Polyamide 66 (PA66)-Based Hybrid Polymer Composites
por: Demirsöz, Recep, et al.
Publicado: (2022)

Evaluation of Mechanical and Tribological Aspect of Self-Lubricating Cu-6Gr Composites Reinforced with SiC–WC Hybrid Particles
por: Usca, Üsame Ali, et al.
Publicado: (2022)

Enhancement of Mechanical Properties of Flax-Epoxy Composite with Carbon Fibre Hybridisation for Lightweight Applications
por: Dhakal, Hom Nath, et al.
Publicado: (2019)

Modeling of Cutting Parameters and Tool Geometry for Multi-Criteria Optimization of Surface Roughness and Vibration via Response Surface Methodology in Turning of AISI 5140 Steel
por: Kuntoğlu, Mustafa, et al.
Publicado: (2020)

Optimization and Analysis of Surface Roughness, Flank Wear and 5 Different Sensorial Data via Tool Condition Monitoring System in Turning of AISI 5140
por: Kuntoğlu, Mustafa, et al.
Publicado: (2020)

Elucidating the Effect of Step Cooling Heat Treatment on the Properties of 2.25 Cr–1.0 Mo Steel Welded with a Combination of GMAW Techniques Incorporating Metal-Cored Wires
por: Das, Subhash, et al.
Publicado: (2021)

Development of an Oxide Layer on Al 6061 Using Plasma Arc Electrolytic Oxidation in Silicate-Based Electrolyte
por: Jadhav, Priya, et al.
Publicado: (2022)

An Experimental and Numerical Investigation into the Durability of Fibre/Polymer Composites with Synthetic and Natural Fibres
por: Alajmi, Abdalrahman, et al.
Publicado: (2022)

Attenuation measurements in scintillating glass fibres
por: Demagh, N, et al.
Publicado: (1985)

Tribological Aspects, Optimization and Analysis of Cu-B-CrC Composites Fabricated by Powder Metallurgy
por: Usca, Üsame Ali, et al.
Publicado: (2021)

Surface Roughness Evaluation in Thin EN AW-6086-T6 Alloy Plates after Face Milling Process with Different Strategies
por: Chuchala, Daniel, et al.
Publicado: (2021)

Study of a Multicriterion Decision-Making Approach to the MQL Turning of AISI 304 Steel Using Hybrid Nanocutting Fluid
por: Dubey, Vineet, et al.
Publicado: (2021)

Thermal Conductivity of Structural Glass/Fibre Epoxy Composite as a Function of Fibre Orientation
por: Cugnet, D, et al.
Publicado: (2002)

Identifying Defects in Aerospace Composite Sandwich Panels Using High-Definition Distributed Optical Fibre Sensors
por: Mills, James A., et al.
Publicado: (2020)

Establishing the Relationship between Cutting Speed and Output Parameters in Belt Grinding on Steels, Aluminum and Nickel Alloys: Development of Recommendations
por: Syreyshchikova, Nelli Vladimirovna, et al.
Publicado: (2021)

Measurement of Micro Burr and Slot Widths through Image Processing: Comparison of Manual and Automated Measurements in Micro-Milling
por: Akkoyun, Fatih, et al.
Publicado: (2021)

Hand and Abrasive Flow Polished Tungsten Carbide Die: Optimization of Surface Roughness, Polishing Time and Comparative Analysis in Wire Drawing
por: Kumar, Raman, et al.
Publicado: (2022)

Magnesium Coated Bioresorbable Phosphate Glass Fibres: Investigation of the Interface between Fibre and Polyester Matrices
por: Liu, Xiaoling, et al.
Publicado: (2013)

Design and tribological performance of short S-Glass fibre reinforced biocomposites on the influence of fibre length and concentration
por: Raju, et al.
Publicado: (2023)

Mechanical and Tribological Performances of Thermoplastic Polymers Reinforced with Glass Fibres at Variable Fibre Volume Fractions
por: Zaghloul, Moustafa Mahmoud Yousry, et al.
Publicado: (2023)

Radiation resistant Epoxy Glass fibre Laminates
por: Eichberger, W
Publicado: (1994)

Effect of Cryogenic Grinding on Fatigue Life of Additively Manufactured Maraging Steel
por: Balan, Arunachalam S. S., et al.
Publicado: (2021)

The Effect of Zn and Zn–WO(3) Composites Nano-Coatings Deposition on Hardness and Corrosion Resistance in Steel Substrate
por: Kumar, Channagiri Mohankumar Praveen, et al.
Publicado: (2021)

Multi-Response Optimization of Al(2)O(3) Nanopowder-Mixed Wire Electrical Discharge Machining Process Parameters of Nitinol Shape Memory Alloy
por: Chaudhari, Rakesh, et al.
Publicado: (2022)

Parametric Optimization and Influence of Near-Dry WEDM Variables on Nitinol Shape Memory Alloy
por: Chaudhari, Rakesh, et al.
Publicado: (2022)

Experimental Investigations and Effect of Nano-Powder-Mixed EDM Variables on Performance Measures of Nitinol SMA
por: Chaudhari, Rakesh, et al.
Publicado: (2022)

Comparative studies of experimental and numerical evaluation of tensile properties of Glass Fibre Reinforced Polyester (GFRP) matrix
por: Ndukwe, Christopher O., et al.
Publicado: (2021)

Influence of Stress Level and Fibre Volume Fraction on Fatigue Performance of Glass Fibre-Reinforced Polyester Composites
por: Zaghloul, Mahmoud Yousry, et al.
Publicado: (2022)

Impact Strength of Preplaced Aggregate Concrete Comprising Glass Fibre Mesh and Steel Fibres: Experiments and Modeling
por: Ponnambalam, Nirmal, et al.
Publicado: (2022)

Relationship between Pressure and Output Parameters in Belt Grinding of Steels and Nickel Alloy
por: Syreyshchikova, Nelli Vladimirovna, et al.
Publicado: (2021)

Fibre typing of intrafusal fibres
por: Thornell, Lars-Eric, et al.
Publicado: (2015)

Microstructure, Mechanical, and Corrosion Behavior of Al(2)O(3) Reinforced Mg2Zn Matrix Magnesium Composites
por: Ercetin, Ali, et al.
Publicado: (2021)

Optimization and Modeling of Material Removal Rate in Wire-EDM of Silicon Particle Reinforced Al6061 Composite
por: Doreswamy, Deepak, et al.
Publicado: (2021)

Corrosion Resistance and Surface Bioactivity of Ti6Al4V Alloy after Finish Turning under Ecological Cutting Conditions
por: Leksycki, Kamil, et al.
Publicado: (2021)

Cannot write session to /tmp/vufind_sessions/sess_c9d2or9rfeb9o091s8echntssn