Cargando…

The Effect of Coatings on Cutting Force in Turning of C45 Steel

This article focuses on the development of a mathematical model of a cutting force that is applicable for coated and uncoated cutting tool inserts and aims to enable more accurate calculation of the cutting force. Two common PVD coatings, AlTiN and TiAlCrN, were used. Firstly, a mathematical model o...

Descripción completa

Detalles Bibliográficos
Autores principales:	Kovalčík, Jaroslav, Mašek, Petr, Malý, Jan, Kožmín, Pavel, Syrovátka, Jiří
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2022
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC8777703/ https://www.ncbi.nlm.nih.gov/pubmed/35057307 http://dx.doi.org/10.3390/ma15020590

Ejemplares similares

Method for an Effective Selection of Tools and Cutting Conditions during Precise Turning of Non-Alloy Quality Steel C45
por: Ivchenko, Oleksandr, et al.
Publicado: (2022)

An Experimental Investigation of Controlled Changes in Wettability of Laser-Treated Surfaces after Various Post Treatment Methods
por: Primus, Tomáš, et al.
Publicado: (2021)

The Influence of Cutting Parameters on Plastic Deformation and Chip Compression during the Turning of C45 Medium Carbon Steel and 62SiMnCr4 Tool Steel
por: Kuruc, Marcel, et al.
Publicado: (2022)

Tribological Aspects of Cutting Tool Wear during the Turning of Stainless Steels
por: Zawada-Michałowska, Magdalena, et al.
Publicado: (2019)

Effect of Centrifugal Shot Peening on the Surface Properties of Laser-Cut C45 Steel Parts
por: Skoczylas, Agnieszka, et al.
Publicado: (2019)

Cutting Forces during Inconel 718 Orthogonal Turn-Milling
por: Felusiak-Czyryca, Agata, et al.
Publicado: (2021)

Comparison of Tool Wear, Surface Roughness, Cutting Forces, Tool Tip Temperature, and Chip Shape during Sustainable Turning of Bearing Steel
por: Demirpolat, Havva, et al.
Publicado: (2023)

A High Performance Sensor for Triaxial Cutting Force Measurement in Turning
por: Zhao, You, et al.
Publicado: (2015)

Selected Properties of the Surface Layer of C45 Steel Parts Subjected to Laser Cutting and Ball Burnishing
por: Skoczylas, Agnieszka, et al.
Publicado: (2020)

The Influence of the Depth of Cut in Single-Pass Grinding on the Microstructure and Properties of the C45 Steel Surface Layer
por: Szkodo, Marek, et al.
Publicado: (2020)

Investigation of Multiparameter Laser Stripping of AlTiN and DLC C Coatings
por: Primus, Tomáš, et al.
Publicado: (2021)

Design and Development of a Tri-Axial Turning Dynamometer Utilizing Cross-Beam Type Force Transducer for Fine-Turning Cutting Force Measurement
por: Rizal, Muhammad, et al.
Publicado: (2022)

Influence of Different Grades of CBN Inserts on Cutting Force and Surface Roughness of AISI H13 Die Tool Steel during Hard Turning Operation
por: Kumar, Pardeep, et al.
Publicado: (2019)

Analysis and prediction of residual stresses based on cutting temperature and cutting force in rough turning of Ti–6Al–4V
por: Li, Guo, et al.
Publicado: (2022)

Investigation on the Performance of Coated Carbide Tool during Dry Turning of AISI 4340 Alloy Steel
por: Wagri, Naresh Kumar, et al.
Publicado: (2023)

Study of Wear, Stress and Vibration Characteristics of Silicon Carbide Tool Inserts and Nano Multi-Layered Titanium Nitride-Coated Cutting Tool Inserts in Turning of SS304 Steels
por: Ganeshkumar, S., et al.
Publicado: (2022)

Analysis of Wear Resistance of Borided Steel C45
por: Pashechko, Mykhaylo, et al.
Publicado: (2020)

Cutting Performance Evaluation of the Coated Tools in High-Speed Milling of AISI 4340 Steel
por: Li, Yuan, et al.
Publicado: (2019)

Cutting Forces and Tool Wear Investigation during Turning of Sintered Nickel-Cobalt Alloy with CBN Tools
por: Zębala, Wojciech, et al.
Publicado: (2021)

Assessment of CVD- and PVD-Coated Carbides and PVD-Coated Cermet Inserts in the Optimization of Surface Roughness in Turning of AISI 1045 Steel
por: Paese, Evandro, et al.
Publicado: (2020)

The Effect of Cutting Fluid on Machined Surface Integrity of Ultra-High-Strength Steel 45CrNiMoVA
por: Wang, Yubin, et al.
Publicado: (2023)

Quantifying Cutting and Wearing Behaviors of TiN- and CrN-Coated AISI 1070 Steel
por: Cakan, Ahmet, et al.
Publicado: (2008)

NiCrBSi Coatings Fabricated on 45 Steel Using Large Spot Laser Cladding
por: Zhao, Longjie, et al.
Publicado: (2022)

Experimental data-set for prediction of tool wear during turning of Al-1061 alloy by high speed steel cutting tools
por: Okokpujie, I.P., et al.
Publicado: (2018)

Data-set collected during turning operation of AISI 1045 alloy steel with green cutting fluids in near dry condition
por: Dennison, Milon Selvam, et al.
Publicado: (2020)

Quantum dissipation driven by electron transfer within a single molecule investigated with atomic force microscopy
por: Berger, Jan, et al.
Publicado: (2020)

A Harmonized Perspective on Transportation Management in Smart Cities: The Novel IoT-Driven Environment for Road Traffic Modeling
por: Masek, Pavel, et al.
Publicado: (2016)

Proteins mimicking epitope of HIV-1 virus neutralizing antibody induce virus-neutralizing sera in mice
por: Kosztyu, Petr, et al.
Publicado: (2019)

Extraesophageal Reflux: What Is the Best Parameter for pH-Monitoring Data Analysis from the Perspective of Patient Response to Proton Pump Inhibitors?
por: Zelenik, Karol, et al.
Publicado: (2013)

Effect of Steel-Cutting Technology on Fatigue Strength of Steel Structures: Tests and Analyses
por: Rowiński, Sławomir
Publicado: (2021)

Investigation of Cutting Temperature during Turning Inconel 718 with (Ti,Al)N PVD Coated Cemented Carbide Tools
por: Zhao, Jinfu, et al.
Publicado: (2018)

Cutting Force Prediction Models by FEA and RSM When Machining X56 Steel with Single Diamond Grit
por: Zhang, Lan, et al.
Publicado: (2021)

Effect of high-speed steel screw drill geometry on cutting performance when machining austenitic stainless steel
por: Sedlak, Josef, et al.
Publicado: (2023)

Finite Element Simulation and Experimental Assessment of Laser Cutting Unidirectional CFRP at Cutting Angles of 45° and 90°
por: Keuntje, Jan, et al.
Publicado: (2023)

Constant mixing temperature test of a fin-and-tube latent heat thermal energy storage
por: Jančík, Petr, et al.
Publicado: (2022)

Myomedin scaffold variants targeted to 10E8 HIV-1 broadly neutralizing antibody mimic gp41 epitope and elicit HIV-1 virus-neutralizing sera in mice
por: Kuchař, Milan, et al.
Publicado: (2021)

A New Alloying Concept for Low-Density Steels
por: Hájek, Jiří, et al.
Publicado: (2022)

Modeling of Cutting Parameters and Tool Geometry for Multi-Criteria Optimization of Surface Roughness and Vibration via Response Surface Methodology in Turning of AISI 5140 Steel
por: Kuntoğlu, Mustafa, et al.
Publicado: (2020)

Comparative Evaluation of Surface Quality, Tool Wear, and Specific Cutting Energy for Wiper and Conventional Carbide Inserts in Hard Turning of AISI 4340 Alloy Steel
por: Abbas, Adel T., et al.
Publicado: (2020)

Turning Copper and Aluminum Alloys with Natural Rocks as Cutting Tools
por: Breidenstein, Bernd, et al.
Publicado: (2022)

Cannot write session to /tmp/vufind_sessions/sess_rm6r3okm1177dem598r32n48g3