Cargando…

Simulation and Experimental Study on Roll-Forming Limit of Cup

Roll forming can improve the material utilization rate and production efficiency of cups with a curved rotary profile, but there is no basis for the determination of forming limit. The DEFORM-3D software was used to simulate the roll forming of cups. The influence of the billet wall thickness and bo...

Descripción completa

Detalles Bibliográficos
Autores principales:	Zhang, Baohong, Ning, Shengpeng, Wei, Zeng, Duan, Yali, Li, Xubin, Yang, Yongbiao
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2022
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC8877326/ https://www.ncbi.nlm.nih.gov/pubmed/35207822 http://dx.doi.org/10.3390/ma15041279

Ejemplares similares

Numerical Simulation and Experimental Investigation of Cold-Rolled Steel Cutting
por: Kaczmarczyk, Jarosław, et al.
Publicado: (2018)

Numerical Simulation of Tube Manufacturing Consisting of Roll Forming and High-Frequency Induction Welding
por: Egger, Christian, et al.
Publicado: (2022)

Development of Measurement Equipment and Experimental and Numerical Simulation Studies for Warm Forming Limits of High-Strength Steel
por: Yu, Qiang, et al.
Publicado: (2021)

Combined Therapies of Modified Taiyi Miraculous Moxa Roll and Cupping for Patients with Lumbar Intervertebral Disc Herniation
por: Cai, Chunyue, et al.
Publicado: (2018)

Three-dimensional morphodynamic simulations of macropinocytic cups
por: Saito, Nen, et al.
Publicado: (2021)

A Comparative Analysis of Forming Railway Axles in 3- and 4-Roll Rolling Mills
por: Pater, Zbigniew
Publicado: (2020)

An Innovative Method for Forming Balls by Cross Rolling
por: Pater, Zbigniew, et al.
Publicado: (2018)

Simulation-Based Process Design for Asymmetric Single-Point Incremental Forming of Individual Titanium Alloy Hip Cup Prosthesis
por: Frikha, Sirine, et al.
Publicado: (2022)

Physical Modeling of Cross Wedge Rolling Limitations
por: Wójcik, Łukasz, et al.
Publicado: (2020)

Forming Quality Analysis on the Cold Roll Forming C-channel Steel
por: Hui, Xiangjun, et al.
Publicado: (2018)

Forming Quality Research on the Variable-Diameter Section of the Hollow Axle in Three-Roll Skew Rolling
por: Xia, Yingxiang, et al.
Publicado: (2022)

The Analysis of Pressed Cups Producing Possibilities from Rolled Bimetallic Al-1050 + Cu-M1E Sheets
por: Rydz, Dariusz, et al.
Publicado: (2020)

Optimization of cold rolling process parameters in order to increasing rolling speed limited by chatter vibrations
por: Heidari, Ali, et al.
Publicado: (2013)

The effect of geometry and abduction angle on the stresses in cemented UHMWPE acetabular cups – finite element simulations and experimental tests
por: Korhonen, Rami K, et al.
Publicado: (2005)

The Effects of Forming Parameters on Conical Ring Rolling Process
por: Meng, Wen, et al.
Publicado: (2014)

Cold rolling precision forming of shaft parts: theory and technologies
por: Song, Jianli, et al.
Publicado: (2017)

Application of RoboCup 3D and Intelligent Technology in Football Simulation League
por: Wei, Shenghui, et al.
Publicado: (2022)

Self-organizing actin waves that simulate phagocytic cup structures
por: Gerisch, Günther
Publicado: (2010)

Experimental and Numerical Investigation of AA5052-H32 Al Alloy with U-Profile in Cold Roll Forming
por: Murugesan, Mohanraj, et al.
Publicado: (2021)

An Experimental Investigation of Steel Surface Topography Transfer by Cold Rolling
por: Xu, Dong, et al.
Publicado: (2020)

Optimization of the Forming Method on Torsion Defect in Cold-Roll Forming of Z Section Steel
por: Wang, Yesong, et al.
Publicado: (2022)

Heterodimer formed by ROC8 and ROC5 modulates leaf rolling in rice
por: Xu, Yang, et al.
Publicado: (2021)

Influence of Processing Parameters on the Thread and Spline Synchronous Rolling Process: An Experimental Study
por: Zhang, Da-Wei, et al.
Publicado: (2019)

Analysis of the Innovative Channel Strut Concept Manufactured by Roll-Forming
por: Kochański, Andrzej, et al.
Publicado: (2022)

Application of Mean Modulus in Three-Point Bending and Roll Forming
por: Xing, Menglong, et al.
Publicado: (2023)

Simulation study of a Faraday-cup monitor for single-bunch electron beams
por: Suwada, T
Publicado: (1998)

Hijama (Wet Cupping or Dry Cupping) for Diabetes Treatment
por: Vakilinia, Seyed Reza, et al.
Publicado: (2016)

Best bone of acetabulum for cup component placement in Crowe types I to III dysplastic hips: a computer simulation study
por: Zheng, Lin-Li, et al.
Publicado: (2019)

Experimental limits on the form factors in K°μ3 decay
por: Peach, Kenneth J, et al.
Publicado: (1973)

Unlocking Deformation Path in Asymmetric Rolling by Texture Simulation
por: Dhinwal, Satyaveer Singh, et al.
Publicado: (2019)

Numerical Simulation of the Hot Rolling Process of Steel Beams
por: Pérez-Alvarado, Alejandro, et al.
Publicado: (2021)

Experimental Validation of High Precision Web Handling for a Two-Actuator-Based Roll-to-Roll System
por: Kim, Jaeyoung, et al.
Publicado: (2022)

Effect of Differential Speed Rotation Technology on the Forming Uniformity in Flexible Rolling Process
por: Li, Yi, et al.
Publicado: (2018)

Heat Build-Up and Rolling Resistance Analysis of a Solid Tire: Experimental Observation and Numerical Simulation with Thermo-Mechanical Coupling Method
por: He, Hong, et al.
Publicado: (2022)

The cup of youth
por: Dumit, Verónica I, et al.
Publicado: (2014)

On the Operation of Cupping
Publicado: (1809)

Observations on Cupping
Publicado: (1809)

On the Operation of Cupping
Publicado: (1809)

Measuring Cup
Publicado: (1866)

Dry Cupping
por: Washington, B. H.
Publicado: (1875)

Cannot write session to /tmp/vufind_sessions/sess_2lvluee4j88aiabeio2512199v