Cargando…

Improvement of the PLA Crystallinity and Heat Distortion Temperature Optimizing the Content of Nucleating Agents and the Injection Molding Cycle Time

Three different commercial nucleating agents (LAK, talc, and calcium carbonate) were added at different weight percentages into poly (lactic acid) (PLA) in order to investigate the mechanical and thermo-mechanical behavior of blends in correlation to injection molding parameters. After as-sessing th...

Descripción completa

Detalles Bibliográficos
Autores principales:	Aliotta, Laura, Sciara, Letizia Maria, Cinelli, Patrizia, Canesi, Ilaria, Lazzeri, Andrea
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2022
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC8912521/ https://www.ncbi.nlm.nih.gov/pubmed/35267797 http://dx.doi.org/10.3390/polym14050977

Ejemplares similares

Improvement of Interfacial Adhesion and Thermomechanical Properties of PLA Based Composites with Wheat/Rice Bran
por: Gigante, Vito, et al.
Publicado: (2022)

Poly(lactic acid) (PLA)/Poly(butylene succinate-co-adipate) (PBSA) Compatibilized Binary Biobased Blends: Melt Fluidity, Morphological, Thermo-Mechanical and Micromechanical Analysis
por: Aliotta, Laura, et al.
Publicado: (2021)

Essential Work of Fracture and Evaluation of the Interfacial Adhesion of Plasticized PLA/PBSA Blends with the Addition of Wheat Bran By-Product
por: Aliotta, Laura, et al.
Publicado: (2022)

Effect of a Bio-Based Dispersing Aid (Einar(®) 101) on PLA-Arbocel(®) Biocomposites: Evaluation of the Interfacial Shear Stress on the Final Mechanical Properties
por: Aliotta, Laura, et al.
Publicado: (2020)

Chitin Nanofibrils in Poly(Lactic Acid) (PLA) Nanocomposites: Dispersion and Thermo-Mechanical Properties
por: Coltelli, Maria-Beatrice, et al.
Publicado: (2019)

Investigation of Novel Flax Fiber/Epoxy Composites with Increased Biobased Content
por: Dal Pont, Bianca, et al.
Publicado: (2023)

Micromechanical Deformation Processes and Failure of PBS Based Composites Containing Ultra-Short Cellulosic Fibers for Injection Molding Applications
por: Aliotta, Laura, et al.
Publicado: (2022)

Evaluation of Mussel Shells Powder as Reinforcement for PLA-Based Biocomposites
por: Gigante, Vito, et al.
Publicado: (2020)

A Brief Review of Poly (Butylene Succinate) (PBS) and Its Main Copolymers: Synthesis, Blends, Composites, Biodegradability, and Applications
por: Aliotta, Laura, et al.
Publicado: (2022)

Dielectric Spectroscopy of PP/MWCNT Nanocomposites: Relationship with Crystalline Structure and Injection Molding Condition
por: Monti, Marco, et al.
Publicado: (2021)

Influence of Heat Sink on the Mold Temperature of Gypsum Mold Used in Injection Molding
por: Lin, Chung-Chih, et al.
Publicado: (2020)

Volume Change during Creep and Micromechanical Deformation Processes in PLA–PBSA Binary Blends
por: Aliotta, Laura, et al.
Publicado: (2021)

Poly(lactic acid) (PLA) Based Tear Resistant and Biodegradable Flexible Films by Blown Film Extrusion
por: Mallegni, Norma, et al.
Publicado: (2018)

Effect of Injection Molding Conditions on Crystalline Structure and Electrical Resistivity of PP/MWCNT Nanocomposites
por: Zaccone, Marta, et al.
Publicado: (2020)

Improved Impact Properties in Poly(lactic acid) (PLA) Blends Containing Cellulose Acetate (CA) Prepared by Reactive Extrusion
por: Coltelli, Maria-Beatrice, et al.
Publicado: (2019)

Evaluation of Mechanical and Interfacial Properties of Bio-Composites Based on Poly(Lactic Acid) with Natural Cellulose Fibers
por: Aliotta, Laura, et al.
Publicado: (2019)

PLA Biocomposites: Evaluation of Resistance to Mold
por: Borysiuk, Piotr, et al.
Publicado: (2021)

Effect of Rapid Mold Heating on the Structure and Performance of Injection-Molded Polypropylene
por: Liparoti, Sara, et al.
Publicado: (2020)

Analysis, Development, and Scaling-Up of Poly(lactic acid) (PLA) Biocomposites with Hazelnuts Shell Powder (HSP)
por: Aliotta, Laura, et al.
Publicado: (2021)

Analysis of the Damage Mechanism around the Crack Tip for Two Rubber-Toughened PLA-Based Blends
por: Gigante, Vito, et al.
Publicado: (2021)

Injection Molding of Low-Density Polyethylene (LDPE) as a Model Polymer: Effect of Molding Parameters on the Microstructure and Crystallinity
por: Leyva-Porras, César, et al.
Publicado: (2021)

Replication of Micro- and Nanofeatures in Injection Molding of Two PLA Grades with Rapid Surface-Temperature Modulation
por: Liparoti, Sara, et al.
Publicado: (2018)

Thermal, Mechanical, Viscoelastic and Morphological Properties of Poly(lactic acid) based Biocomposites with Potato Pulp Powder Treated with Waxes
por: Righetti, Maria Cristina, et al.
Publicado: (2019)

Sustainable Micro and Nano Additives for Controlling the Migration of a Biobased Plasticizer from PLA-Based Flexible Films
por: Aliotta, Laura, et al.
Publicado: (2020)

Manufacturing PLA/PCL Blends by Ultrasonic Molding Technology
por: Ferrer, Inés, et al.
Publicado: (2021)

Constrained Amorphous Interphase and Mechanical Properties of Poly(3-Hydroxybutyrate-co-3-Hydroxyvalerate)
por: Righetti, Maria Cristina, et al.
Publicado: (2019)

Chain Extension of Poly(Lactic Acid) (PLA)–Based Blends and Composites Containing Bran with Biobased Compounds for Controlling Their Processability and Recyclability
por: Coltelli, Maria-Beatrice, et al.
Publicado: (2021)

Design and Simulation Study of the Induction Heated Injection Mold with Sliders
por: Muszyński, Paweł, et al.
Publicado: (2021)

Enhanced Injection Molding Simulation of Advanced Injection Molds
por: Zink, Béla, et al.
Publicado: (2017)

Characterization of Optimized Ternary PLA/PHB/Organoclay Composites Processed through Fused Filament Fabrication and Injection Molding
por: Buyuksoy-Fekraoui, Kubra, et al.
Publicado: (2022)

Influence of the ion content of CaCl(2)-ionised polyamide-66 nucleator on the crystalline nucleation of poly(ethylene terephthalate) through ion–dipole interactions
por: Tian, Yuanfu, et al.
Publicado: (2020)

On the Use of Paper Sludge as Filler in Biocomposites for Injection Moulding
por: Gigante, Vito, et al.
Publicado: (2021)

Analytical Modeling of Stress Relaxation and Evaluation of the Activation Volume Variation: Effect of Temperature and Plasticizer Content for Poly(3-hydroxybutyrate-3-hydroxyvalerate)
por: Aliotta, Laura, et al.
Publicado: (2022)

Correlation between Processing Parameters, Morphology, and Properties of Injection-Molded Polylactid Acid (PLA) Specimens at Different Length Scales
por: Meinig, Laura, et al.
Publicado: (2023)

Influence of the Mold Material on the Injection Molding Cycle Time and Warpage Depending on the Polymer Processed
por: Lucyshyn, Thomas, et al.
Publicado: (2021)

Injection Molding of 3-3 Hydroxyapatite Composites
por: Biggemann, Jonas, et al.
Publicado: (2020)

Liquid and Solid Functional Bio-Based Coatings
por: Gigante, Vito, et al.
Publicado: (2021)

Improvement of the Gas Barrier Properties of PLA/OMMT Films by Regulating the Interlayer Spacing of OMMT and the Crystallinity of PLA
por: Li, Fenfen, et al.
Publicado: (2020)

An Investigation on the Efficacy of Orotic Acid as a Bio-Nucleating Agent for Poly-Lactic Acid under Quiescent Condition and Injection Molding
por: Gao, Peng, et al.
Publicado: (2022)

Preparation and Compatibilization of PBS/Whey Protein Isolate Based Blends
por: Coltelli, Maria-Beatrice, et al.
Publicado: (2020)

Cannot write session to /tmp/vufind_sessions/sess_j9gmeg553d3mp5fifncguof8ec