Cargando…

The Influence of the Process Parameters on the Mechanical Properties of PLA Specimens Produced by Fused Filament Fabrication—A Review

Polylactic acid (PLA) is produced from renewable materials, has a low melting temperature and has a low carbon footprint. These advantages have led to the extensive use of polylactic acid in additive manufacturing, particularly by fused filament fabrication (FFF). PLA parts that are 3D printed for i...

Descripción completa

Detalles Bibliográficos
Autores principales:	Cojocaru, Vasile, Frunzaverde, Doina, Miclosina, Calin-Octavian, Marginean, Gabriela
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2022
Materias:	Review
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC8912674/ https://www.ncbi.nlm.nih.gov/pubmed/35267709 http://dx.doi.org/10.3390/polym14050886

Ejemplares similares

The Influence of the Layer Height and the Filament Color on the Dimensional Accuracy and the Tensile Strength of FDM-Printed PLA Specimens
por: Frunzaverde, Doina, et al.
Publicado: (2023)

The Influence of the Printing Temperature and the Filament Color on the Dimensional Accuracy, Tensile Strength, and Friction Performance of FFF-Printed PLA Specimens
por: Frunzaverde, Doina, et al.
Publicado: (2022)

On the Behavior of Honeycomb, Grid and Triangular PLA Structures under Symmetric and Asymmetric Bending
por: Cojocaru, Vasile, et al.
Publicado: (2022)

Development of Antimicrobial PLA Composites for Fused Filament Fabrication
por: Brounstein, Zachary, et al.
Publicado: (2021)

Performance Analysis of Colored PLA Products with a Fused Filament Fabrication Process
por: Spina, Roberto
Publicado: (2019)

Feasibility of Producing Core-Shell Filaments through Fused Filament Fabrication
por: Sover, Alexandru, et al.
Publicado: (2021)

Establishing a Framework for Fused Filament Fabrication Process Optimization: A Case Study with PLA Filaments
por: Grubbs, Jack, et al.
Publicado: (2023)

The Mechanical, Thermal, and Chemical Properties of PLA-Mg Filaments Produced via a Colloidal Route for Fused-Filament Fabrication
por: Orellana-Barrasa, Jaime, et al.
Publicado: (2022)

Effects of Accelerating the Ageing of 1D PLA Filaments after Fused Filament Fabrication
por: Orellana-Barrasa, Jaime, et al.
Publicado: (2022)

Investigating the Material Properties and Microstructural Changes of Fused Filament Fabricated PLA and Tough-PLA Parts
por: Naveed, Nida
Publicado: (2021)

The Transferability and Design of Commercial Printer Settings in PLA/PBAT Fused Filament Fabrication
por: Wang, Sisi, et al.
Publicado: (2020)

Fatigue Performance of ABS Specimens Obtained by Fused Filament Fabrication
por: Domingo-Espin, Miquel, et al.
Publicado: (2018)

Hygromechanical Performance of Polyamide Specimens Made with Fused Filament Fabrication
por: Spina, Roberto, et al.
Publicado: (2021)

Impact Toughness of Hybrid Carbon Fiber-PLA/ABS Laminar Composite Produced through Fused Filament Fabrication
por: Ahmed, Hafiz, et al.
Publicado: (2021)

Mechanical and Geometric Performance of PLA-Based Polymer Composites Processed by the Fused Filament Fabrication Additive Manufacturing Technique
por: Reverte, José María, et al.
Publicado: (2020)

Characterization of Optimized Ternary PLA/PHB/Organoclay Composites Processed through Fused Filament Fabrication and Injection Molding
por: Buyuksoy-Fekraoui, Kubra, et al.
Publicado: (2022)

Optimization of the 3D Printing Parameters for Tensile Properties of Specimens Produced by Fused Filament Fabrication of 17-4PH Stainless Steel
por: Godec, Damir, et al.
Publicado: (2020)

Investigations of Cavitation Erosion and Corrosion Behavior of Flame-Sprayed NiCrBSi/WC-12Co Composite Coatings
por: Ciubotariu, Costel-Relu, et al.
Publicado: (2022)

Optimization of Printing Parameters to Enhance Tensile Properties of ABS and Nylon Produced by Fused Filament Fabrication
por: Yankin, Andrei, et al.
Publicado: (2023)

On the Strain Rate Sensitivity of Fused Filament Fabrication (FFF) Processed PLA, ABS, PETG, PA6, and PP Thermoplastic Polymers
por: Vidakis, Nectarios, et al.
Publicado: (2020)

Effect of Extrusion Parameters on Short Fiber Alignment in Fused Filament Fabrication
por: Consul, Patrick, et al.
Publicado: (2021)

Sterilization of PLA after Fused Filament Fabrication 3D Printing: Evaluation on Inherent Sterility and the Impossibility of Autoclavation
por: Neijhoft, Jonas, et al.
Publicado: (2023)

Fabrication of hydrophobic PLA filaments for additive manufacturing
por: Rajakaruna, Rajakaruna A. D. N. V., et al.
Publicado: (2022)

Effects of Environmental Temperature and Humidity on the Geometry and Strength of Polycarbonate Specimens Prepared by Fused Filament Fabrication
por: Fang, Lichen, et al.
Publicado: (2020)

Composite Polyurethane-Polylactide (PUR/PLA) Flexible Filaments for 3D Fused Filament Fabrication (FFF) of Antibacterial Wound Dressings for Skin Regeneration
por: Szarlej, Paweł, et al.
Publicado: (2021)

Thermoforming Characteristics of PLA/TPU Multi-Material Specimens Fabricated with Fused Deposition Modelling under Different Temperatures
por: Sorimpuk, Neilson Peter, et al.
Publicado: (2022)

Fused Filament Deposition of PLA: The Role of Interlayer Adhesion in the Mechanical Performances
por: Liparoti, Sara, et al.
Publicado: (2021)

Influence of the Infill Orientation on the Properties of Zirconia Parts Produced by Fused Filament Fabrication
por: Cano, Santiago, et al.
Publicado: (2020)

Fused Filament Fabrication Process: A Review of Numerical Simulation Techniques
por: Rashid, Ans Al, et al.
Publicado: (2021)

Fabrication of PLA/PCL/Graphene Nanoplatelet (GNP) Electrically Conductive Circuit Using the Fused Filament Fabrication (FFF) 3D Printing Technique
por: Masarra, Nour-Alhoda, et al.
Publicado: (2022)

Fused Filament Fabrication of Small Ceramic Components
por: Nötzel, Dorit, et al.
Publicado: (2018)

Thermal Properties and In Vitro Biodegradation of PLA-Mg Filaments for Fused Deposition Modeling
por: Leonés, Adrián, et al.
Publicado: (2023)

Experimental Study on Metal Parts under Variable 3D Printing and Sintering Orientations Using Bronze/PLA Hybrid Filament Coupled with Fused Filament Fabrication
por: Wei, Xueying, et al.
Publicado: (2022)

Fused Filament Fabrication of Alumina/Polymer Filaments for Obtaining Ceramic Parts after Debinding and Sintering Processes
por: Tosto, Claudio, et al.
Publicado: (2022)

In-Situ Monitoring and Diagnosing for Fused Filament Fabrication Process Based on Vibration Sensors
por: Li, Yongxiang, et al.
Publicado: (2019)

Fused Filament Fabrication of PEEK: A Review of Process-Structure-Property Relationships
por: Zanjanijam, Ali Reza, et al.
Publicado: (2020)

Characterization of the Metal Fused Filament Fabrication Process for Manufacturing of Pure Copper Inductors
por: Schüßler, Philipp, et al.
Publicado: (2023)

Influence of Infill Pattern on Mechanical Behavior of Polymeric and Composites Specimens Manufactured Using Fused Filament Fabrication Technology
por: Martín, María Jesús, et al.
Publicado: (2021)

The Mechanical Properties of Thin-Walled Specimens Printed from a Bronze-Filled PLA-Based Composite Filament Using Fused Deposition Modelling
por: Bochnia, Jerzy, et al.
Publicado: (2023)

3D PEEK Objects Fabricated by Fused Filament Fabrication (FFF)
por: Baek, Inwoo, et al.
Publicado: (2022)

Cannot write session to /tmp/vufind_sessions/sess_1bi1hpvu2s5vdquqj5hp0v1qcn