Cargando…

Effect of Tool Positioning Factors on the Strength of Dissimilar Friction Stir Welded Joints of AA7075-T6 and AA6061-T6

Friction Stir Welding (FSW) is a solid-state bonding technique. There are many direct and indirect factors affecting the mechanical and microstructural properties of the FSW joints. Tool offset, tilt angle, and plunge depth are determinative tool positioning in the FSW process. Investigating the eff...

Descripción completa

Detalles Bibliográficos
Autores principales:	Ghiasvand, Amir, Noori, Saja Mohammed, Suksatan, Wanich, Tomków, Jacek, Memon, Shabbir, Derazkola, Hesamoddin Aghajani
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2022
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC8999929/ https://www.ncbi.nlm.nih.gov/pubmed/35407798 http://dx.doi.org/10.3390/ma15072463

Ejemplares similares

Investigation of the Effects of Tool Positioning Factors on Peak Temperature in Dissimilar Friction Stir Welding of AA6061-T6 and AA7075-T6 Aluminum Alloys
por: Ghiasvand, Amir, et al.
Publicado: (2022)

Investigation of Mechanical and Microstructural Properties of Welded Specimens of AA6061-T6 Alloy with Friction Stir Welding and Parallel-Friction Stir Welding Methods
por: Ghiasvand, Amir, et al.
Publicado: (2021)

Mechanical Properties Enhancement of Dissimilar AA6061-T6 and AA7075-T651 Friction Stir Welds Coupled with Deep Rolling Process
por: Kaewkham, Pisit, et al.
Publicado: (2022)

Thermo-Mechanical Simulation of Underwater Friction Stir Welding of Low Carbon Steel
por: Memon, Shabbir, et al.
Publicado: (2021)

Pin Angle Thermal Effects on Friction Stir Welding of AA5058 Aluminum Alloy: CFD Simulation and Experimental Validation
por: Chupradit, Supat, et al.
Publicado: (2021)

Fracture Behavior of AA7075-AA6061 and AA7075-Cu Friction-Stir Welded Joints Containing Blunt V-Notches under Opening-Mode Loading
por: Torabi, Ali Reza, et al.
Publicado: (2023)

Multi-Objective Optimization of Friction Stir Welding Process Parameters of AA6061-T6 and AA7075-T6 Using a Biogeography Based Optimization Algorithm
por: Tamjidy, Mehran, et al.
Publicado: (2017)

Dissimilar Friction Stir Welding of AA2519 and AA5182
por: Zuiko, Ivan S., et al.
Publicado: (2022)

Post Weld Heat Treatment Optimization of Dissimilar Friction Stir Welded AA2024-T3 and AA7075-T651 Using Machine Learning and Metaheuristics
por: Insua, Pinmanee, et al.
Publicado: (2023)

Effect of Load on the Corrosion Behavior of Friction Stir Welded AA 7075-T6 Aluminum Alloy
por: Cabrini, Marina, et al.
Publicado: (2020)

Effects of Underwater Friction Stir Welding Heat Generation on Residual Stress of AA6068-T6 Aluminum Alloy
por: Khalaf, Hassanein I., et al.
Publicado: (2022)

The Influence of Tool Wear on the Mechanical Performance of AA6061-T6 Refill Friction Stir Spot Welds
por: de Carvalho, Willian S., et al.
Publicado: (2021)

Experimental and Numerical Analysis of Refill Friction Stir Spot Welding of Thin AA7075-T6 Sheets
por: Janga, Venkata Somi Reddy, et al.
Publicado: (2021)

Analysis of Friction Stir Welding Tool Offset on the Bonding and Properties of Al–Mg–Si Alloy T-Joints
por: Memon, Shabbir, et al.
Publicado: (2021)

Effect of Heat Treatment on the Microstructure and Mechanical Properties of Rotary Friction Welded AA7075 and AA5083 Dissimilar Joint
por: Mahajan, Aditya M., et al.
Publicado: (2023)

Microstructure Evolution during Dissimilar Friction Stir Welding of AA7003-T4 and AA6060-T4
por: Dong, Jialiang, et al.
Publicado: (2018)

Texture-Induced Corrosion Resistance of Dissimilar AA7204/AA6082 Friction Stir Welded Joints
por: Guan, Liqun, et al.
Publicado: (2023)

Interface Formation of Medium-Thick AA6061 Al/AZ31B Mg Dissimilar Submerged Friction Stir Welding Joints
por: Huang, Tifang, et al.
Publicado: (2022)

The Influence of Tool Geometry on the Mechanical Properties and the Microstructure of AA6061-T6 Aluminum Alloy Friction Stir Spot Welding
por: Alkhafaji, Amir, et al.
Publicado: (2023)

Mechanical Properties and Microstructure of Dissimilar S355/AA6061-T6 FSW Butt Joints
por: Ziółkowski, Wojciech, et al.
Publicado: (2023)

Effects of Partial-Contact Tool Tilt Angle on Friction Stir Welded AA1050 Aluminum Joint Properties
por: Abdullah, Mahmoud E., et al.
Publicado: (2023)

Microstructure and Mechanical Properties of Dissimilar Friction Stir Welded Joint AA7020/AA5083 with Different Joining Parameters
por: Torzewski, Janusz, et al.
Publicado: (2022)

Comparative Insight into the Interfacial Phase Evolutions during Solution Treatment of Dissimilar Friction Stir Welded AA2198-AA7475 and AA2198-AA6013 Aluminum Sheets
por: Jandaghi, Mohammad Reza, et al.
Publicado: (2021)

Effect of Welding Parameters on Mechanical Properties and Microstructure of Friction Stir Welded AA7075-T651 Aluminum Alloy Butt Joints
por: Kosturek, Robert, et al.
Publicado: (2022)

Double side friction stir welding effect on mechanical properties and corrosion rate of aluminum alloy AA6061
por: Priyasudana, Danang, et al.
Publicado: (2023)

Friction Stir Welding of Dissimilar Al 6061-T6 to AISI 316 Stainless Steel: Microstructure and Mechanical Properties
por: Newishy, Mohamed, et al.
Publicado: (2023)

Friction Stir Welding and Friction Spot Stir Welding Processes of Polymers—State of the Art
por: Lambiase, Francesco, et al.
Publicado: (2020)

A Novel Friction Stir Deposition Technique to Refill Keyhole of Friction Stir Spot Welded AA6082-T6 Dissimilar Joints of Different Sheet Thicknesses
por: Ahmed, Mohamed M. Z., et al.
Publicado: (2022)

A Review on AA 6061 Metal Matrix Composites Produced by Stir Casting
por: Kareem, Ansar, et al.
Publicado: (2021)

Flat hardness distribution in AA6061 joints by linear friction welding
por: Choi, Jeong-Won, et al.
Publicado: (2021)

Sequential Effects of Deep Rolling and Post-Weld Heat Treatment on Surface Integrity of AA7075-T651 Aluminum Alloy Friction Stir Welding
por: Baisukhan, Adirek, et al.
Publicado: (2019)

Fabrication of Sputtered Ce/La, La/Ce Oxide Bilayers on AA6061 and AA7075 Aluminum Alloys for the Development of Corrosion Protective Coatings
por: Brachetti-Sibaja, Silvia B., et al.
Publicado: (2018)

Effect of Pin Shape on Thermal History of Aluminum-Steel Friction Stir Welded Joint: Computational Fluid Dynamic Modeling and Validation
por: Bokov, Dmitry Olegovich, et al.
Publicado: (2021)

A Numerical Study on the Effect of Tool Speeds on Temperatures and Material Flow Behaviour in Refill Friction Stir Spot Welding of Thin AA7075-T6 Sheets
por: Janga, Venkata Somi Reddy, et al.
Publicado: (2023)

High-Power Fiber Laser Welding of High-Strength AA7075-T6 Aluminum Alloy Welds for Mechanical Properties Research
por: El-Batahgy, Abdel-Monem, et al.
Publicado: (2021)

Effects of Noncontact Shoulder Tool Velocities on Friction Stir Joining of Polyamide 6 (PA6)
por: Al-Sabur, Raheem, et al.
Publicado: (2022)

Friction Stir Spot Welding of Different Thickness Sheets of Aluminum Alloy AA6082-T6
por: Ahmed, Mohamed M. Z., et al.
Publicado: (2022)

The Study on the Overall Plasma Electrolytic Oxidation for 6061–7075 Dissimilar Aluminum Alloy Welded Parts Based on the Dielectric Breakdown Theory
por: Chen, Yanfei, et al.
Publicado: (2018)

Formation Mechanism of Thicker Intermetallic Compounds in Friction Stir Weld Joints of Dissimilar AA2024/AZ31B Alloys
por: Tan, Maoju, et al.
Publicado: (2022)

Evolution of Microstructure in Friction Stir Processed Dissimilar CuZn37/AA5056 Stir Zone
por: Zykova, Anna, et al.
Publicado: (2021)

Cannot write session to /tmp/vufind_sessions/sess_o5e6d6ekhedpdkbbd0136pq6gg