Cargando…

Fused-Filament Fabrication of Short Carbon Fiber-Reinforced Polyamide: Parameter Optimization for Improved Performance under Uniaxial Tensile Loading

This study intends to contribute to the state of the art of Fused-Filament Fabrication (FFF) of short-fiber-reinforced polyamides by optimizing process parameters to improve the performance of printed parts under uniaxial tensile loading. This was performed using two different approaches: a more tra...

Descripción completa

Detalles Bibliográficos
Autores principales:	Belei, Carlos, Joeressen, Jana, Amancio-Filho, Sergio T.
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2022
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC9002508/ https://www.ncbi.nlm.nih.gov/pubmed/35406166 http://dx.doi.org/10.3390/polym14071292

Ejemplares similares

Post-Process Effects of Isothermal Annealing and Initially Applied Static Uniaxial Loading on the Ultimate Tensile Strength of Fused Filament Fabrication Parts
por: Rane, Rhugdhrivya, et al.
Publicado: (2020)

Hygromechanical Performance of Polyamide Specimens Made with Fused Filament Fabrication
por: Spina, Roberto, et al.
Publicado: (2021)

Mechanical Behaviour of ABS-Fused Filament Fabrication Compounds under Impact Tensile Loadings
por: Casavola, Caterina, et al.
Publicado: (2019)

Fused Filament Fabricated Polypropylene Composite Reinforced by Aligned Glass Fibers
por: Shulga, Eugene, et al.
Publicado: (2020)

Optimization of Printing Parameters to Enhance Tensile Properties of ABS and Nylon Produced by Fused Filament Fabrication
por: Yankin, Andrei, et al.
Publicado: (2023)

Water Influence on the Uniaxial Tensile Behavior of Polytetrafluoroethylene-Coated Glass Fiber Fabric
por: Asadi, Hastia, et al.
Publicado: (2021)

Continuous Fiber-Reinforced Aramid/PETG 3D-Printed Composites with High Fiber Loading through Fused Filament Fabrication
por: Rijckaert, Sander, et al.
Publicado: (2022)

Thermal, Tensile and Fatigue Behaviors of the PA6, Short Carbon Fiber-Reinforced PA6, and Continuous Glass Fiber-Reinforced PA6 Materials in Fused Filament Fabrication (FFF)
por: Ahmadifar, Mohammad, et al.
Publicado: (2023)

Effect of Extrusion Parameters on Short Fiber Alignment in Fused Filament Fabrication
por: Consul, Patrick, et al.
Publicado: (2021)

Uniaxial Tensile Behavior of Carbon Textile Reinforced Mortar
por: Zhou, Fen, et al.
Publicado: (2019)

Investigation of the Failure Modes of Textile-Reinforced Concrete and Fiber/Textile-Reinforced Concrete under Uniaxial Tensile Tests
por: Mattarollo, Giorgio, et al.
Publicado: (2023)

Bending Strength of Polyamide-Based Composites Obtained during the Fused Filament Fabrication (FFF) Process
por: Mazurkiewicz, Michał, et al.
Publicado: (2022)

Mathematical Modeling and Optimization of Fused Filament Fabrication (FFF) Process Parameters for Shape Deviation Control of Polyamide 6 Using Taguchi Method
por: Shakeri, Zohreh, et al.
Publicado: (2021)

On the Mechanical Performance of Polylactic Material Reinforced by Ceramic in Fused Filament Fabrication
por: Hedjazi, Lotfi, et al.
Publicado: (2022)

Fused Filament Fabrication of Polymers and Continuous Fiber-Reinforced Polymer Composites: Advances in Structure Optimization and Health Monitoring
por: Mashayekhi, Fatemeh, et al.
Publicado: (2021)

Optimization of the 3D Printing Parameters for Tensile Properties of Specimens Produced by Fused Filament Fabrication of 17-4PH Stainless Steel
por: Godec, Damir, et al.
Publicado: (2020)

Investigation of the Manufacturing Orientation Impact on the Mechanical Properties of Composite Fiber-Reinforced Polymer Elements in the Fused Filament Fabrication Process
por: Spišák, Emil, et al.
Publicado: (2023)

Optimization of Process Parameters for Carbon Fiber Reinforced Polyamide 6 Composites Fabricated by Self-Resistance Electric Heating Technology
por: Zhai, Zhanyu, et al.
Publicado: (2023)

Fabrication and Characterisation of Aligned Discontinuous Carbon Fibre Reinforced Thermoplastics as Feedstock Material for Fused Filament Fabrication
por: Blok, Lourens Gerrit, et al.
Publicado: (2020)

Fiber Orientation and Strain Rate-Dependent Tensile and Compressive Behavior of Injection Molded Polyamide-6 Reinforced with 20% Short Carbon Fiber
por: Lee, Joonhee, et al.
Publicado: (2023)

Compression and Bending Properties of Short Carbon Fiber Reinforced Polymers Sandwich Structures Produced via Fused Filament Fabrication Process
por: Zaharia, Sebastian Marian, et al.
Publicado: (2022)

Fused Filament Fabrication of Short Glass Fiber-Reinforced Polylactic Acid Composites: Infill Density Influence on Mechanical and Thermal Properties
por: Chicos, Lucia-Antoneta, et al.
Publicado: (2022)

Fused Filament Fabricated Poly(lactic acid) Parts Reinforced with Short Carbon Fiber and Graphene Nanoparticles with Improved Tribological Properties
por: Al Abir, Anzum, et al.
Publicado: (2023)

Creep-recovery behaviors of articular cartilage under uniaxial and biaxial tensile loadings
por: Gao, Lilan, et al.
Publicado: (2023)

3D Printing of Polyamide to Fabricate a Non-Metal Clasp Removable Partial Denture via Fused Filament Fabrication: A Case Report
por: Spintzyk, Sebastian, et al.
Publicado: (2021)

Polyamide Fiber Reinforced Shotcrete for Tunnel Application
por: Jeon, Joong Kyu, et al.
Publicado: (2016)

High-Impact Polystyrene Reinforced with Reduced Graphene Oxide as a Filament for Fused Filament Fabrication 3D Printing
por: Sieradzka, Marta, et al.
Publicado: (2021)

Uniaxial Tensile Behavior, Flexural Properties, Empirical Calculation and Microstructure of Multi-Scale Fiber Reinforced Cement-Based Material at Elevated Temperature
por: Li, Li, et al.
Publicado: (2021)

Fabrication and Characterization of Carbon Fiber-Reinforced Nano-Hydroxyapatite/Polyamide46 Biocomposite for Bone Substitute
por: Deng, Zhennan, et al.
Publicado: (2017)

A Review on Reinforcement Methods for Polymeric Materials Processed Using Fused Filament Fabrication (FFF)
por: Pratama, Juan, et al.
Publicado: (2021)

Performance Simulation and Fused Filament Fabrication Modeling of the Wave-Absorbing Structure of Conductive Multi-Walled Carbon Nanotube/Polyamide 12 Composite
por: Han, Baigang, et al.
Publicado: (2023)

Effect of Manufacture-Induced Interfaces on the Tensile Properties of 3D Printed Polyamide and Short Carbon Fibre-Reinforced Polyamide Composites
por: Hou, Yingwei, et al.
Publicado: (2023)

Fused Filament Fabrication of Small Ceramic Components
por: Nötzel, Dorit, et al.
Publicado: (2018)

Fabrication, Tensile Properties, and Photodecomposition of Basalt Fiber-Reinforced Cellulose Acetate Matrix Composites
por: Shen, Yuxi, et al.
Publicado: (2021)

Effect of Infill Patterns with Machine Learning Techniques on the Tensile Properties of Polylactic Acid-Based Ceramic Materials with Fused Filament Fabrication
por: Lolla, Ranganath, et al.
Publicado: (2023)

Mechanical and Physical Properties of Recycled-Carbon-Fiber-Reinforced Polylactide Fused Deposition Modelling Filament
por: Omar, Nur’ain Wahidah Ya, et al.
Publicado: (2021)

Feasibility of Producing Core-Shell Filaments through Fused Filament Fabrication
por: Sover, Alexandru, et al.
Publicado: (2021)

Fabrication of Carbon Fiber Reinforced Aromatic Polyamide Composites and Their Thermal Conductivities with a h-BN Filler
por: Lee, Min Jun, et al.
Publicado: (2020)

Failure Mechanisms and Reinforcing Modes of Ply Splice Fiber-Reinforced Composite Laminates under Tensile Load
por: Zhu, Meng, et al.
Publicado: (2019)

3D Printing of Fibre-Reinforced Thermoplastic Composites Using Fused Filament Fabrication—A Review
por: Dickson, Andrew N., et al.
Publicado: (2020)

Cannot write session to /tmp/vufind_sessions/sess_1mhtmp7fuc24qqutjteo8nbhf2