Cargando…

Coating-thickness-dependent physical properties and cutting temperature for cutting Inconel 718 with TiAlN coated tools

INTRODUCTION: Coating-thickness-dependent physical properties can induce different cutting temperatures with physical vapor deposition (PVD) titanium aluminum nitride (TiAlN) ceramic-coated tools. The determination of the optimal TiAlN coating thickness is important to obtain superior coating physic...

Descripción completa

Detalles Bibliográficos
Autores principales:	Zhao, Jinfu, Liu, Zhanqiang, Ren, Xiaoping, Wang, Bing, Cai, Yucui, Song, Qinghua, Wan, Yi
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	Elsevier 2021
Materias:	Mathematics, Engineering, and Computer Science
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC9091928/ https://www.ncbi.nlm.nih.gov/pubmed/35572412 http://dx.doi.org/10.1016/j.jare.2021.07.009

Ejemplares similares

Investigation of Cutting Temperature during Turning Inconel 718 with (Ti,Al)N PVD Coated Cemented Carbide Tools
por: Zhao, Jinfu, et al.
Publicado: (2018)

Effects of Cutting Edge Microgeometry on Residual Stress in Orthogonal Cutting of Inconel 718 by FEM
por: Shen, Qi, et al.
Publicado: (2018)

Influences of Cutting Speed and Material Mechanical Properties on Chip Deformation and Fracture during High-Speed Cutting of Inconel 718
por: Wang, Bing, et al.
Publicado: (2018)

Optimization of Micro-Texturing Process Parameters of TiAlN Coated Cutting Tools by Femtosecond Laser
por: Wu, Xuefeng, et al.
Publicado: (2022)

Cutting Forces during Inconel 718 Orthogonal Turn-Milling
por: Felusiak-Czyryca, Agata, et al.
Publicado: (2021)

Milling of an Al/CFRP Sandwich Construction with Non-Coated and TiAlN-Coated Tools
por: Doluk, Elżbieta, et al.
Publicado: (2020)

Oxidation behavior of the TiAlN hard coating in the process of recycling coated hardmetal scrap
por: Kuang, Hai, et al.
Publicado: (2019)

Crystallite size-dependent metastable phase formation of TiAlN coatings
por: Hans, Marcus, et al.
Publicado: (2017)

An Investigation of the Work Hardening Behavior in Interrupted Cutting Inconel 718 under Cryogenic Conditions
por: Dai, Xing, et al.
Publicado: (2020)

Experimental Study on Drilling MDF with Tools Coated with TiAlN and ZrN
por: Szwajka, Krzysztof, et al.
Publicado: (2019)

Properties of TiAlN Coatings Obtained by Dual-HiPIMS with Short Pulses
por: Grenadyorov, Alexander, et al.
Publicado: (2023)

Influence of Microgroove Structure on Cutting Performance and Chip Morphology during the Turning of Superalloy Inconel 718
por: Zou, Zhongfei, et al.
Publicado: (2021)

Tribological Behaviors of Super-Hard TiAlN Coatings Deposited by Filtered Cathode Vacuum Arc Deposition
por: Zhang, Zhiqiang, et al.
Publicado: (2022)

Comparison of Surface Morphology and Tool Wear in the Machining of Ti-6Al-4V Alloys with Uncoated and TiAlN Tools under Dry, Minimum Quantity Lubrication, Flood Cooling, and Low-Temperature Spray Jet Cooling Conditions
por: Zhao, Jinfu, et al.
Publicado: (2023)

Modelling the Kerf Angle, Roughness and Waviness of the Surface of Inconel 718 in an Abrasive Water Jet Cutting Process
por: Płodzień, Marcin, et al.
Publicado: (2023)

Effects of Machined Surface Integrity on High-Temperature Low-Cycle Fatigue Life and Process Parameters Optimization of Turning Superalloy Inconel 718
por: Ren, Xiaoping, et al.
Publicado: (2021)

Study of TiAlN PVD Coating on Stamping Dies Used in Tinplate Food Package Production
por: Fernandes, Liliana, et al.
Publicado: (2019)

Investigation of the Oxidation Behaviour of Ti and Al in Inconel 718 Superalloy During Electroslag Remelting
por: Duan, Shengchao, et al.
Publicado: (2018)

Optimization of Cutting Process Parameters in Inclined Drilling of Inconel 718 Using Finite Element Method and Taguchi Analysis
por: Pervaiz, Salman, et al.
Publicado: (2020)

Study of the Effects of Initial Cutting Conditions and Transition Period on Ultimate Tool Life when Machining Inconel 718
por: Memarianpour, Morvarid, et al.
Publicado: (2021)

Study on the Effects of Different Cutting Angles on the End-Milling of Wire and Arc Additive Manufacturing Inconel 718 Workpieces
por: dos Santos, Gustavo Quadra Vieira, et al.
Publicado: (2022)

Temperature Measurement and Numerical Prediction in Machining Inconel 718
por: Díaz-Álvarez, José, et al.
Publicado: (2017)

Phase Stability and Elasticity of TiAlN
por: Abrikosov, Igor A., et al.
Publicado: (2011)

Features of electronic and lattice mechanisms of transboundary heat transfer in multilayer nanolaminate TiAlN/Ag coatings
por: Kovalev, A. I., et al.
Publicado: (2017)

The Oxidation Behaviour and Notch Wear Formation of TiAlN Coated Tools Using Different Oxidation Techniques
por: Grzesik, Wit, et al.
Publicado: (2021)

Influence of Different Types of Cemented Carbide Blades and Coating Thickness on Structure and Properties of TiN/AlTiN and TiAlN/a-C:N Coatings Deposited by PVD Techniques for Machining of Wood-Based Materials
por: Kucharska, Beata, et al.
Publicado: (2021)

Modeling and Prediction of Water-Jet-Guided Laser Cutting Depth for Inconel 718 Material Using Response Surface Methodology
por: Zhao, Chuang, et al.
Publicado: (2023)

Experimental Investigation of Principal Residual Stress and Fatigue Performance for Turned Nickel-Based Superalloy Inconel 718
por: Hua, Yang, et al.
Publicado: (2018)

High temperature performance of wire-arc additive manufactured Inconel 718
por: James, William Sean, et al.
Publicado: (2023)

Thermal Shock and Oxidation Behavior of HiPIMS TiAlN Coatings Grown on Ti-48Al-2Cr-2Nb Intermetallic Alloy
por: Badini, Claudio, et al.
Publicado: (2016)

Enhancement of Multi-Scale Self-Organization Processes during Inconel DA 718 Machining through the Optimization of TiAlCrSiN/TiAlCrN Bi-Nano-Multilayer Coating Characteristics
por: Fox-Rabinovitch, Guerman, et al.
Publicado: (2022)

Effect of Coating Thickness on Abrasion and Cutting Performance of NCD-Coated Ball Endmills on Graphite Machining
por: Lee, Hyeonhwa, et al.
Publicado: (2023)

Comprehensive Research and Analysis of a Coated Machining Tool with a New TiAlN Composite Microlayer Using Magnetron Sputtering
por: Michna, Štefan, et al.
Publicado: (2021)

Studies on the Microstructural Evolution and Mechanical Properties of Superalloy Inconel 718 Induced by Low Plasticity Burnishing Coupled with Turning
por: Hua, Yang, et al.
Publicado: (2022)

Effect of Ball Burnishing Pressure on Surface Roughness by Low Plasticity Burnishing Inconel 718 Pre-Turned Surface
por: Cui, Pengcheng, et al.
Publicado: (2022)

Investigation of the Influence of Anti-Wear Coatings on the Surface Quality and Dimensional Accuracy during Finish Turning of the Inconel 718 Alloy
por: Smak, Krzysztof, et al.
Publicado: (2023)

Performance Evaluation of Vegetable Oil-Based Nano-Cutting Fluids in Environmentally Friendly Machining of Inconel-800 Alloy
por: Gupta, Munish Kumar, et al.
Publicado: (2019)

Experimental Study of Direct Laser Deposition of Ti-6Al-4V and Inconel 718 by Using Pulsed Parameters
por: Shah, Kamran, et al.
Publicado: (2014)

Achieving the Minimum Roughness of Laser Milled Micro-Impressions on Ti 6Al 4V, Inconel 718, and Duralumin
por: Ahmed, Naveed, et al.
Publicado: (2020)

Study of Phase Evolution Behavior of Ti6Al4V/Inconel 718 by Pulsed Laser Melting Deposition
por: Wang, Yuanhao, et al.
Publicado: (2023)

Cannot write session to /tmp/vufind_sessions/sess_dq0nakj5ubcdfn02lcfqcfm4hd