Cargando…

Deformation Analysis of Continuous Milling of Inconel718 Nickel-Based Superalloy

As a difficult-to-process material, Inconel718 nickel-based superalloy is more and more widely used in aerospace, ocean navigation, and large-scale machinery manufacturing. Based on ABAQUS simulation software, this paper takes the milling force and temperature in the milling process of the nickel-ba...

Descripción completa

Detalles Bibliográficos
Autores principales:	Li, Xueguang, Wang, Yahui, Miao, Liqin, Zhang, Wang
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2022
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC9144658/ https://www.ncbi.nlm.nih.gov/pubmed/35630150 http://dx.doi.org/10.3390/mi13050683

Ejemplares similares

Milling Mechanism and Chattering Stability of Nickel-Based Superalloy Inconel 718
por: Zheng, Jin, et al.
Publicado: (2023)

Experimental Investigation of Principal Residual Stress and Fatigue Performance for Turned Nickel-Based Superalloy Inconel 718
por: Hua, Yang, et al.
Publicado: (2018)

Temperature-Based Prediction of Joint Hardness in TIG Welding of Inconel 600, 625 and 718 Nickel Superalloys
por: Jamrozik, Wojciech, et al.
Publicado: (2021)

Grain Refinement of Inconel 718 Superalloy—The Effect of Rotating Magnetic Field
por: Silva, Rui Pedro, et al.
Publicado: (2022)

Influence of Heat Treatment on Cyclic Response of Nickel-Based Superalloy Inconel 718 up to Very-High Cycle Regime
por: Zhao, Mengxiong, et al.
Publicado: (2020)

Study of the Influence of Shielding Gases on Laser Metal Deposition of Inconel 718 Superalloy
por: Ruiz, Jose Exequiel, et al.
Publicado: (2018)

Investigation of the Machinability of the Inconel 718 Superalloy during the Electrical Discharge Drilling Process
por: Machno, Magdalena
Publicado: (2020)

Influence of Selective Laser Melting Additive Manufacturing Parameters in Inconel 718 Superalloy
por: Kladovasilakis, Nikolaos, et al.
Publicado: (2022)

Effect of Pressure and Temperature on Densification in Electric Field-Assisted Sintering of Inconel 718 Superalloy
por: Ma, Liyong, et al.
Publicado: (2021)

Investigation of the Oxidation Behaviour of Ti and Al in Inconel 718 Superalloy During Electroslag Remelting
por: Duan, Shengchao, et al.
Publicado: (2018)

Cutting Forces during Inconel 718 Orthogonal Turn-Milling
por: Felusiak-Czyryca, Agata, et al.
Publicado: (2021)

Effect of Laser Remelting on Cladding Layer of Inconel 718 Superalloy Formed by Laser Metal Deposition
por: Xin, Bo, et al.
Publicado: (2020)

Metal fused filament fabrication of the nickel-base superalloy IN 718
por: Thompson, Yvonne, et al.
Publicado: (2022)

Influence of Microgroove Structure on Cutting Performance and Chip Morphology during the Turning of Superalloy Inconel 718
por: Zou, Zhongfei, et al.
Publicado: (2021)

Formability, Microstructure and Properties of Inconel 718 Superalloy Fabricated by Selective Laser Melting Additive Manufacture Technology
por: Liu, Xiaoping, et al.
Publicado: (2021)

Effect of Ultrasonic Surface Rolling Process on the Hot Compression Behavior of Inconel 718 Superalloy at 700 °C
por: Sun, Zhiyan, et al.
Publicado: (2019)

Effects of the γ″-Ni(3)Nb Phase on Mechanical Properties of Inconel 718 Superalloys with Different Heat Treatments
por: Ling, Li-Shi-Bao, et al.
Publicado: (2019)

The δ Phase Precipitation of an Inconel 718 Superalloy Fabricated by Electromagnetic Stirring Assisted Laser Solid Forming
por: Lyu, Feiyue, et al.
Publicado: (2019)

A Study on the Optimal Machining Parameters of the Induction Assisted Milling with Inconel 718
por: Kim, Eun Jung, et al.
Publicado: (2019)

Laser Engineered Net Shaping of Nickel-Based Superalloy Inconel 718 Powders onto AISI 4140 Alloy Steel Substrates: Interface Bond and Fracture Failure Mechanism
por: Kim, Hoyeol, et al.
Publicado: (2017)

Studies on the Microstructural Evolution and Mechanical Properties of Superalloy Inconel 718 Induced by Low Plasticity Burnishing Coupled with Turning
por: Hua, Yang, et al.
Publicado: (2022)

Comparison of Flank Super Abrasive Machining vs. Flank Milling on Inconel(®) 718 Surfaces
por: González, Haizea, et al.
Publicado: (2018)

Quantitative Characterization of Elemental Segregation in Inconel 718 Superalloy by Micro-Beam X-ray Fluorescence Spectroscopy and Its Correlation Study
por: Zhou, Xuefan, et al.
Publicado: (2023)

Influence of Homogenization on Phase Transformations during Isothermal Aging of Inconel 718 Superalloys Fabricated by Additive Manufacturing and Suction Casting
por: Zhao, Yunhao, et al.
Publicado: (2023)

Effect of Pre-Stress on Laser-Induced Thermoplastic Deformation of Inconel 718 Beams
por: Widłaszewski, Jacek, et al.
Publicado: (2021)

Multi-Objective Optimization of Process Parameters during Micro-Milling of Nickel-Based Alloy Inconel 718 Using Taguchi-Grey Relation Integrated Approach
por: Sheheryar, Muhammad, et al.
Publicado: (2022)

Oxidation Behavior of Inconel 740H Nickel Superalloy in Steam Atmosphere at 750 °C
por: Kościelniak, Barbara, et al.
Publicado: (2021)

On the Anisotropic Milling Machinability of DD407 Single Crystal Nickel-Based Superalloy
por: Qiu, Jun, et al.
Publicado: (2022)

Effects of Machined Surface Integrity on High-Temperature Low-Cycle Fatigue Life and Process Parameters Optimization of Turning Superalloy Inconel 718
por: Ren, Xiaoping, et al.
Publicado: (2021)

Selective Anisotropy of Mechanical Properties in Inconel718 Alloy
por: Liang, Yu, et al.
Publicado: (2021)

Precipitates in Additively Manufactured Inconel 625 Superalloy
por: Dubiel, Beata, et al.
Publicado: (2019)

Effects of the γ″-Ni(3)Nb Phase on Fatigue Behavior of Nickel-Based 718 Superalloys with Different Heat Treatments
por: Ling, Li-Shi-Bao, et al.
Publicado: (2019)

Temperature Measurement and Numerical Prediction in Machining Inconel 718
por: Díaz-Álvarez, José, et al.
Publicado: (2017)

Study on the Effects of Different Cutting Angles on the End-Milling of Wire and Arc Additive Manufacturing Inconel 718 Workpieces
por: dos Santos, Gustavo Quadra Vieira, et al.
Publicado: (2022)

Measuring the effect of residual stress on the machined subsurface of Inconel 718 by nanoindentation
por: Chen, Ling, et al.
Publicado: (2021)

Fabrication and Characterization of the Newly Developed Superalloys Based on Inconel 740
por: Grudzień-Rakoczy, Małgorzata, et al.
Publicado: (2020)

Influence of Size Effect in Milling of a Single-Crystal Nickel-Based Superalloy
por: Soriano Gonzalez, Luis, et al.
Publicado: (2023)

Achieving the Minimum Roughness of Laser Milled Micro-Impressions on Ti 6Al 4V, Inconel 718, and Duralumin
por: Ahmed, Naveed, et al.
Publicado: (2020)

Impact of Notches on Additively Manufactured Inconel 718 Tensile Performance
por: Johnson, Joseph, et al.
Publicado: (2023)

Simulation of Work Hardening in Machining Inconel 718 with Multiscale Grain Size
por: Zhuang, Kejia, et al.
Publicado: (2023)

Cannot write session to /tmp/vufind_sessions/sess_9m8ttkqhuod4nt2ih6tqvrtfcl