Cargando…

High-Precision Thin Wall Bipolar Plates for Fuel Cell Applications via Injection Compression Molding with Dynamic Mold Temperature Control

In recent years, the demand for polymer compound solutions for the application of bipolar plates in polymer electrolyte membrane fuel cells (PEMFC) has increased continuously due to significant cost and lifetime advantages compared to metallic solutions. The main challenge of the compounds is the hi...

Descripción completa

Detalles Bibliográficos
Autores principales:	Roth, Benedikt, Frank, Rainer, Kleffel, Tobias, Schneider, Kevin, Drummer, Dietmar
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2022
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC9318047/ https://www.ncbi.nlm.nih.gov/pubmed/35890575 http://dx.doi.org/10.3390/polym14142799

Ejemplares similares

Investigating the Integration of Nonwoven Carbon Fibers for Mechanical Enhancement in Compression Molded Fiber-Reinforced Polymer Bipolar Plates
por: Frank, Rainer, et al.
Publicado: (2023)

Micro Injection Molding of Thin Cavities Using Stereolithography for Mold Fabrication
por: Surace, Rossella, et al.
Publicado: (2021)

Replicability of Ultrasonic Molding for Processing Thin-Wall Polystyrene Plates with a Microchannel
por: Ferrer, I., et al.
Publicado: (2018)

Characterization of Microchannel Replicability of Injection Molded Electrophoresis Microfluidic Chips
por: Jiang, Bingyan, et al.
Publicado: (2019)

Possibilities of Integrated Fabrication of Insulation Systems in Electric Drives by Injection Molding of Thermosets
por: Rösel, Uta, et al.
Publicado: (2022)

Experimental Characterization and Simulation of Thermoplastic Polymer Flow Hesitation in Thin-Wall Injection Molding Using Direct In-Mold Visualization Technique
por: Regi, Francesco, et al.
Publicado: (2020)

Manufacturing Signatures of Injection Molding and Injection Compression Molding for Micro-Structured Polymer Fresnel Lens Production
por: Loaldi, Dario, et al.
Publicado: (2018)

Enhanced Injection Molding Simulation of Advanced Injection Molds
por: Zink, Béla, et al.
Publicado: (2017)

Injection Compression Molded Microlens Arrays for Hyperspectral Imaging
por: Roeder, Marcel, et al.
Publicado: (2018)

Influence of Heat Sink on the Mold Temperature of Gypsum Mold Used in Injection Molding
por: Lin, Chung-Chih, et al.
Publicado: (2020)

Fabrication of Micro-Structured Polymer by Micro Injection Molding Based on Precise Micro-Ground Mold Core
por: Lu, Yanjun, et al.
Publicado: (2019)

Fabrication of Micro-Structured LED Diffusion Plate Using Efficient Micro Injection Molding and Micro-Ground Mold Core
por: Lu, Yanjun, et al.
Publicado: (2020)

Thermal Conductivity of Aluminosilicate- and Aluminum Oxide-Filled Thermosets for Injection Molding: Effect of Filler Content, Filler Size and Filler Geometry
por: Zhao, Yang, et al.
Publicado: (2018)

In-Mold Sensors for Injection Molding: On the Way to Industry 4.0
por: Ageyeva, Tatyana, et al.
Publicado: (2019)

Multiple In-Mold Sensors for Quality and Process Control in Injection Molding
por: Párizs, Richárd Dominik, et al.
Publicado: (2023)

Pre-Compensation of Mold in Precision Glass Molding Based on Mathematical Analysis
por: Zhang, Yue, et al.
Publicado: (2020)

Improving the Integrated Fabrication of Insulation Systems in Electric Drives by Injection Molding of Thermosets Due to Processing Conditions and Slot Design
por: Rösel, Uta, et al.
Publicado: (2023)

Influence of Processing Parameters on the Mechanical Properties of Peek Plates by Hot Compression Molding
por: Li, Tong, et al.
Publicado: (2022)

Efficient and Precise Micro-Injection Molding of Micro-Structured Polymer Parts Using Micro-Machined Mold Core by WEDM
por: Liao, Qianghua, et al.
Publicado: (2019)

Reducing the Burn Marks on Injection-Molded Parts by External Gas-Assisted Injection Molding
por: Li, Jiquan, et al.
Publicado: (2021)

Hydrophobicity Tuning by the Fast Evolution of Mold Temperature during Injection Molding
por: Liparoti, Sara, et al.
Publicado: (2018)

Effect of Rapid Mold Heating on the Structure and Performance of Injection-Molded Polypropylene
por: Liparoti, Sara, et al.
Publicado: (2020)

Post-Molding Shrinkage, Structure and Properties of Cellular Injection-Molded Polypropylene
por: Kościuszko, Artur, et al.
Publicado: (2022)

Application and Optimization of the Thin Electric Heater in Micro-Injection Mold for Micropillars
por: Weng, Can, et al.
Publicado: (2022)

Optimization of Injection-Molding Process for Thin-Walled Polypropylene Part Using Artificial Neural Network and Taguchi Techniques
por: Moayyedian, Mehdi, et al.
Publicado: (2021)

Handbook of metal injection molding
por: Heaney, Donald F.
Publicado: (2012)

Thermoelasticity of Injection-Molded Parts
por: Turk, Janez, et al.
Publicado: (2023)

Effects of Injection Molding Parameters on Properties of Insert-Injection Molded Polypropylene Single-Polymer Composites
por: Wang, Jian, et al.
Publicado: (2021)

Modeling and Analysis of Morphology of Injection Molding Polypropylene Parts Induced by In-Mold Annealing
por: Salomone, Rita, et al.
Publicado: (2022)

A Comprehensive Review of Micro/Nano Precision Glass Molding Molds and Their Fabrication Methods
por: Asgar, Md. Ali, et al.
Publicado: (2021)

Pressure Analysis of Dynamic Injection Molding and Process Parameter Optimization for Reducing Warpage of Injection Molded Products
por: Wang, Xinyu, et al.
Publicado: (2017)

Influence of the Mold Material on the Injection Molding Cycle Time and Warpage Depending on the Polymer Processed
por: Lucyshyn, Thomas, et al.
Publicado: (2021)

Filling-Balance-Oriented Parameters for Multi-Cavity Molds in Polyvinyl Chloride Injection Molding
por: Tsai, Hsi-Hsun, et al.
Publicado: (2022)

The Microcellular Structure of Injection Molded Thick-Walled Parts as Observed by In-Line Monitoring
por: Sykutera, Dariusz, et al.
Publicado: (2020)

Development of Metal Plate with Internal Structure Utilizing the Metal Injection Molding (MIM) Process
por: Shin, Kwangho, et al.
Publicado: (2013)

Response of ATLAS Injection Molded Scintillators
por: Jankowski, D, et al.
Publicado: (1994)

Injection Molding Plastic Solar Cells
por: Burgués‐Ceballos, Ignasi, et al.
Publicado: (2023)

Advanced Injection Molding Methods: Review
por: Czepiel, Mateusz, et al.
Publicado: (2023)

RF Welding of Dielectric Lossless Foam Particles by the Application of a Dielectric Heatable Coating with High Recycling Potential
por: Schneider, Kevin, et al.
Publicado: (2023)

Modeling fracture behavior in precision glass molding
por: Liu, Gang
Publicado: (2018)

Cannot write session to /tmp/vufind_sessions/sess_vdiuahgi1ai9gq1lfjjarecvt7