Cargando…

多材料3D打印技术制作用于毛细管电泳的非接触电导/激光诱导荧光二合一检测池

Dual detection, which simultaneously employs two complementary detection methods, is a useful approach to enhance the selectivity and sensitivity of capillary electrophoresis (CE). Through dual detection, multiple classes of analytes with different structural and chemical characteristics can be sens...

Descripción completa

Detalles Bibliográficos
Autores principales: ZHANG, Piwang, YANG, Liye, LIU, Qiang, LU, Shangui, LIANG, Ying, ZHANG, Min
Formato: Online Artículo Texto
Lenguaje:English
Publicado: Editorial board of Chinese Journal of Chromatography 2021
Materias:
Acceso en línea:https://www.ncbi.nlm.nih.gov/pmc/articles/PMC9404044/
https://www.ncbi.nlm.nih.gov/pubmed/34212593
http://dx.doi.org/10.3724/SP.J.1123.2021.02021
Descripción
Sumario:Dual detection, which simultaneously employs two complementary detection methods, is a useful approach to enhance the selectivity and sensitivity of capillary electrophoresis (CE). Through dual detection, multiple classes of analytes with different structural and chemical characteristics can be sensitively detected using a single CE method. In addition, the comigrating peaks can be distinguished by comparing the signal outputs of two detectors with different selectivities. Typically, dual detection is achieved by coupling two detectors in series along a capillary. However, in this approach, it is inconvenient to evaluate the signal outputs of the two detectors. The two detectors present differences in their corresponding effective capillary lengths and dead volumes of the detection cell. Therefore, detectors that combine two or three detection methods in a single detection point are proposed to address this issue. In this work, to fabricate a combined detector in a simple and low-cost manner, multimaterial 3D printing technology is employed. A two-in-one detection cell that combines capacitively coupled contactless conductivity detection (C(4)D) and confocal laser-induced fluorescence (LIF) detection was fabricated by 3D printing functional materials. In 3D printing, conductive composite polylactic acid (PLA, Proto-pasta) filaments and normal nonconductive PLA filaments were employed. The conductive material was used to build a C(4)D shielding layer that was electrically grounded. The nonconductive PLA was used as an electrical insulator placed between the shielding layer and C(4)D electrodes, which were two stainless-steel tubes (0.4 mm i.d. and 5 mm length). To embed the electrodes into the nonconductive material, a “print-pause-print” approach was applied. After building two chambers for housing electrodes using nonconductive PLA, the 3D printing was paused, following which the two electrodes were manually installed. Printing was then resumed, and the remaining part was built. The two electrodes were 2 mm apart, and the gap between them was filled with a conductive material for shielding to eliminate stray capacitance. A through-hole (1 mm i.d.) was placed between the middle conductive shielding layer for LIF detection. The size of the detection cell was 60 mm×29 mm×7.2 mm. The cell was screwed onto an XYZ stage to precisely align the light path of LIF detection, which was realized using a TriSep (TM)-2100LIF detector equipped with a 473 nm laser. C(4)D detection was achieved using a TraceDec detector equipped with a ChipCE adaptor. The two-in-one detector was coupled with a lab-made CE system that had a flow-through injection interface. Use of the detection cell allows the simultaneous detection of inorganic cations and fluorescein isothiocyanate (FITC)-labeled amino acids. The C(4)D excitation frequency and buffer concentration were then optimized. A mixture of 10 mmol/L 3-(N-morpholino)propanesulfonic acid (MOPS) and 10 mmol/L bis(2-hydroxyethyl)amino-tris(hydroxymethyl)methane (Bis-Tris) was selected as the background electrolyte as a compromise of C(4)D signal-to-noise ratio (S/N) and separation efficiencies of amino acids. The C(4)D excitation frequency was set to 77 kHz with S/N=233±8 for 200 μmol/L Na (+). The baseline separation of Na(+), K(+), Li(+), FITC, fluorescein, histidine (His), lysine (Lys), tryptophan (Trp), phenylalanine (Phe), alanine (Ala), and glycine (Gly) was achieved with a 25 μm i.d.×365 μm o.d.×45 cm (35 cm effective length) capillary and -10 kV separation voltage. The limits of detection (LODs) of C (4)D for Na(+), K(+), and Li(+)were 2.2, 2.0, and 2.6 μmol/L, respectively. The LODs of LIF for fluorescein and FITC were 7.6 and 1.7 nmol/L, respectively. The relative standard deviations (RSDs) of the two detection methods were within the range of 0.3%-4.5% (n=3). The r (2) of the calibration curves was ≥0.9904. Thus, 3D printing technology is a simple and low-cost approach to implement complex designs, including those that are difficult to fabricate by traditional “workshop” technologies.