Cargando…

Quality Definition in Micro Injection Molding Process by Means of Surface Characterization Parameters

Quality evaluation of micro injection molded products is a complex task, in particular when instruments basing on contact methods are used and issues in measurements could arise due to the contact tool dimension not fitting well with extremely narrow features. Therefore, in these cases, optical meth...

Descripción completa

Detalles Bibliográficos
Autores principales:	Bellantone, Vincenzo, Surace, Rossella, Fassi, Irene
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2022
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC9501567/ https://www.ncbi.nlm.nih.gov/pubmed/36145921 http://dx.doi.org/10.3390/polym14183775

Ejemplares similares

Micro Injection Molding of Thin Cavities Using Stereolithography for Mold Fabrication
por: Surace, Rossella, et al.
Publicado: (2021)

Replication Study of Molded Micro-Textured Samples Made of Ultra-High Molecular Weight Polyethylene for Medical Applications
por: Modica, Francesco, et al.
Publicado: (2023)

Study on the Effect of Processing Parameters on Residual Stresses of Injection Molded Micro-Pillar Array
por: Zhang, Xiaoyu, et al.
Publicado: (2022)

Pressure Analysis of Dynamic Injection Molding and Process Parameter Optimization for Reducing Warpage of Injection Molded Products
por: Wang, Xinyu, et al.
Publicado: (2017)

Multiple In-Mold Sensors for Quality and Process Control in Injection Molding
por: Párizs, Richárd Dominik, et al.
Publicado: (2023)

Effects of Cavity Thickness and Mold Surface Roughness on the Polymer Flow during Micro Injection Molding
por: Li, Jiquan, et al.
Publicado: (2023)

Fabrication of Micro-Patterned Surface for Pool-boiling Enhancement by Using Powder Injection Molding Process
por: Cho, Hanlyun, et al.
Publicado: (2019)

Micro-Injection Molding and Debinding Behavior of Hydroxyapatite/Zirconia Bi-Materials Fabricated by Two-Component Micro-Powder Injection Molding Process
por: Basir, Al, et al.
Publicado: (2023)

Characterization of Stereolithography Printed Soft Tooling for Micro Injection Molding
por: Dempsey, Daniel, et al.
Publicado: (2020)

On the Injection Molding Processing Parameters of HDPE-TiO(2) Nanocomposites
por: Mourad, Abdel-Hamid I., et al.
Publicado: (2017)

Pulse-Type Influence on the Micro-EDM Milling Machinability of Si(3)N(4)–TiN Workpieces
por: Marrocco, Valeria, et al.
Publicado: (2020)

Effects of Injection Molding Parameters on Properties of Insert-Injection Molded Polypropylene Single-Polymer Composites
por: Wang, Jian, et al.
Publicado: (2021)

Fabrication of Micro-Structured Polymer by Micro Injection Molding Based on Precise Micro-Ground Mold Core
por: Lu, Yanjun, et al.
Publicado: (2019)

Effects of Injection Molding Process Parameters on the Chemical Foaming Behavior of Polypropylene and Polystyrene
por: Chung, Chen-Yuan, et al.
Publicado: (2021)

Optimization of injection molding process parameters for the lining of IV hydrogen storage cylinder
por: Li, Jin, et al.
Publicado: (2023)

Optimal Processing Parameters of Transmission Parts of a Flapping-Wing Micro-Aerial Vehicle Using Precision Injection Molding
por: Huang, Huei-Yu, et al.
Publicado: (2022)

Investigation of Product and Process Fingerprints for Fast Quality Assurance in Injection Molding of Micro-Structured Components
por: Giannekas, Nikolaos, et al.
Publicado: (2018)

Modeling the Ultrasonic Micro-Injection Molding Process Using the Buckingham Pi Theorem
por: Salazar-Meza, Marco, et al.
Publicado: (2023)

Injection Molding Micro‐ and Nanostructures in Thermoplastic Elastomers
por: Stormonth‐Darling, John M., et al.
Publicado: (2016)

Analysis of Weld Lines in Micro-Injection Molding
por: Liparoti, Sara, et al.
Publicado: (2023)

Manufacturing Signatures of Injection Molding and Injection Compression Molding for Micro-Structured Polymer Fresnel Lens Production
por: Loaldi, Dario, et al.
Publicado: (2018)

Filling-Balance-Oriented Parameters for Multi-Cavity Molds in Polyvinyl Chloride Injection Molding
por: Tsai, Hsi-Hsun, et al.
Publicado: (2022)

Effect of the Process Parameters on the Adhesive Strength of Dissimilar Polymers Obtained by Multicomponent Injection Molding
por: Pisanu, Luciano, et al.
Publicado: (2021)

Characterization of Arboblend V2 Nature Textured Surfaces Obtained by Injection Molding
por: Mazurchevici, Simona-Nicoleta, et al.
Publicado: (2023)

Fabrication of Micro-Structured LED Diffusion Plate Using Efficient Micro Injection Molding and Micro-Ground Mold Core
por: Lu, Yanjun, et al.
Publicado: (2020)

Efficient and Precise Micro-Injection Molding of Micro-Structured Polymer Parts Using Micro-Machined Mold Core by WEDM
por: Liao, Qianghua, et al.
Publicado: (2019)

Development of an Online Quality Control System for Injection Molding Process
por: Tsai, Ming-Hong, et al.
Publicado: (2022)

Enhanced Injection Molding Simulation of Advanced Injection Molds
por: Zink, Béla, et al.
Publicado: (2017)

Molecular Dynamics Study on the Deformation Behaviors of Nanostructures in the Demolding Process of Micro-Injection Molding
por: Weng, Can, et al.
Publicado: (2019)

Experimental Development of an Injection Molding Process Window
por: Myers, Mason, et al.
Publicado: (2023)

External Gas-Assisted Mold Temperature Control Improves Weld Line Quality in the Injection Molding Process
por: The Uyen, Tran Minh, et al.
Publicado: (2020)

Online Prediction of Molded Part Quality in the Injection Molding Process Using High-Resolution Time Series
por: Bogedale, Lucas, et al.
Publicado: (2023)

Integration of Multivariate Statistical Control Chart and Machine Learning to Identify the Abnormal Process Parameters for Polylactide with Glass Fiber Composites in Injection Molding; Part I: The Processing Parameter Optimization for Multiple Qualities of Polylactide/Glass Fiber Composites in Injection Molding
por: Hsiao, Chi-Hao, et al.
Publicado: (2023)

Replication of Micro- and Nanofeatures in Injection Molding of Two PLA Grades with Rapid Surface-Temperature Modulation
por: Liparoti, Sara, et al.
Publicado: (2018)

Effects of Input Parameter Range on the Accuracy of Artificial Neural Network Prediction for the Injection Molding Process
por: Lee, Junhan, et al.
Publicado: (2022)

Effects of Processing Method and Parameters on the Wall Thickness of Gas-Projectile-Assisted Injection Molding Pipes
por: Kuang, Tangqing, et al.
Publicado: (2023)

Analysis and Validation of Varied Simulation Parameters in the Context of Thermoplastic Foams and Special Injection Molding Processes
por: Oikonomou, Dimitri, et al.
Publicado: (2023)

Weld Line Strength of Polyamide Fiberglass Composite at Different Processing Parameters in Injection Molding Technique
por: Nguyen, Van-Thuc, et al.
Publicado: (2023)

Effects of Process Parameters on Material Removal in Vibration-Assisted Polishing of Micro-Optic Mold
por: Guo, Jiang, et al.
Publicado: (2018)

Molecular Dynamics Simulation on the Influences of Nanostructure Shape, Interfacial Adhesion Energy, and Mold Insert Material on the Demolding Process of Micro-Injection Molding
por: Yang, Jin, et al.
Publicado: (2019)

Cannot write session to /tmp/vufind_sessions/sess_leuokkfqn9oj64riv983thbqth