Cargando…

Influence of Machining Parameters on Cutting and Chip-Formation Process during Cortical Bone Orthogonal Machining

Cortical bone machining is commonly used in craniofacial surgery. The shaping of bone surfaces requires a precise determination of the process’s complexity due to the cutting tool’s defined or undefined geometry. Therefore, research was carried out to assess the impact of the rake angle (γ), clearan...

Descripción completa

Detalles Bibliográficos
Autores principales:	Zawadzki, Paweł, Talar, Rafał, Patalas, Adam, Legutko, Stanisław
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2022
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC9502497/ https://www.ncbi.nlm.nih.gov/pubmed/36143728 http://dx.doi.org/10.3390/ma15186414

Ejemplares similares

The Influence of Osteon Orientation on Surface Topography Parameters after Machining of Cortical Bone Tissue
por: Zawadzki, Paweł, et al.
Publicado: (2023)

Bone Abrasive Machining: Influence of Tool Geometry and Cortical Bone Anisotropic Structure on Crack Propagation
por: Zawadzki, Paweł, et al.
Publicado: (2022)

Study on Technological Effects of a Precise Grooving of AlSi13MgCuNi Alloy with a Novel WCCo/PCD (DDCC) Inserts
por: Wojciechowski, Szymon, et al.
Publicado: (2020)

Chip Formation and Orthogonal Cutting Optimisation of Unidirectional Carbon Fibre Composites
por: Abena, Alessandro, et al.
Publicado: (2023)

On the Chip Shaping and Surface Topography When Finish Cutting 17-4 PH Precipitation-Hardening Stainless Steel under Near-Dry Cutting Conditions
por: Leksycki, Kamil, et al.
Publicado: (2020)

Mechanisms and FEM Simulation of Chip Formation in Orthogonal Cutting In-Situ TiB(2)/7050Al MMC
por: Xiong, Yifeng, et al.
Publicado: (2018)

Investigation of process parameters in orthogonal cutting using finite element approaches
por: Soliman, H.A., et al.
Publicado: (2020)

Serrated Chips Formation in Micro Orthogonal Cutting of Ti6Al4V Alloys with Equiaxial and Martensitic Microstructures
por: Zhao, ZeJia, et al.
Publicado: (2019)

Techniques for Thin-Walled Element Milling with Respect to Minimising Post-Machining Deformations
por: Zawada-Michałowska, Magdalena, et al.
Publicado: (2020)

Prediction of Cutting Force and Chip Formation from the True Stress–Strain Relation Using an Explicit FEM for Polymer Machining
por: Yang, Bin, et al.
Publicado: (2022)

A Numerical Model for Predicting the Effect of Tool Nose Radius on Machining Process Performance during Orthogonal Cutting of AISI 1045 Steel
por: Tagiuri, Zakaria Ahmed M., et al.
Publicado: (2022)

Cutting Forces during Inconel 718 Orthogonal Turn-Milling
por: Felusiak-Czyryca, Agata, et al.
Publicado: (2021)

Microstructure and Properties of Electroless Ni-P/Si(3)N(4) Nanocomposite Coatings Deposited on the AW-7075 Aluminum Alloy
por: Czapczyk, Kazimierz, et al.
Publicado: (2021)

Study on Damage Evaluation and Machinability of UD-CFRP for the Orthogonal Cutting Operation Using Scanning Acoustic Microscopy and the Finite Element Method
por: Wang, Dongyao, et al.
Publicado: (2017)

Cutting Force during Surface Layer Milling of Selected Aluminium Alloys
por: Zawada-Michałowska, Magdalena, et al.
Publicado: (2020)

Experimental Investigation of the Effects of Machining Parameters on the Performance of Form-Cutting Tools Manufactured by Wire Electrical Discharge Machining (WEDM) and Grinding Processes
por: Alinaghizadeh, Amir, et al.
Publicado: (2023)

Computational Analysis of Machining Induced Stress Distribution during Dry and Cryogenic Orthogonal Cutting of 7075 Aluminium Closed Cell Syntactic Foams
por: Thomas, Kevin K., et al.
Publicado: (2023)

Predictive Analytical Modeling of Thermo-Mechanical Effects in Orthogonal Machining
por: Mohamed-Amine, Alliche, et al.
Publicado: (2021)

ECG Classification Using Orthogonal Matching Pursuit and Machine Learning
por: Śmigiel, Sandra
Publicado: (2022)

Analysis of Thermomechanical Properties and the Influence of Machining Process on the Surface Structure of Composites Manufactured from Metal Chips with a Polymer Matrix
por: Gnatowski, Adam, et al.
Publicado: (2022)

A New Cutting Device Design to Study the Orthogonal Cutting of CFRP Laminates at Different Cutting Speeds
por: Criado, Víctor, et al.
Publicado: (2019)

Orthogonal Experimental Study on Concrete Properties of Machine-Made Tuff Sand
por: Liu, Dunwen, et al.
Publicado: (2022)

Advanced machining: the handbook of cutting technology
por: Smith, Graham T
Publicado: (1989)

Cutting machine for elliptical vacuum chambers
por: CERN. Geneva. Super Proton Synchrotron Division (SPS)
Publicado: (1974)

Effects of Cutting Edge Microgeometry on Residual Stress in Orthogonal Cutting of Inconel 718 by FEM
por: Shen, Qi, et al.
Publicado: (2018)

Proposal for a Novel Abrasive Machining Method for Preparing the Surface of Periarticular Tissue during Orthopedic Surgery on Hip Joints
por: Zawadzki, Paweł
Publicado: (2021)

Effects of Machining Parameters and Tool Reconditioning on Cutting Force, Tool Wear, Surface Roughness and Burr Formation in Nickel-Based Alloy Milling
por: Kónya, Gábor, et al.
Publicado: (2023)

Analysis of Carbon Formation on Machined Leather Specimen Using FTIR Technique in Laser Diode Assisted Cutting Process
por: Swaminathan, Vasanth, et al.
Publicado: (2022)

Method of Using the Correlation between the Surface Roughness of Metallic Materials and the Sound Generated during the Controlled Machining Process
por: Nahornyi, Volodymyr, et al.
Publicado: (2022)

Design principles of metal-cutting machine tools
por: Koenigsberger, F
Publicado: (1964)

Manufacturing technology: metal cutting and machine tools
por: Rao, P N
Publicado: (2018)

The Experimental Process Design of Artificial Lightweight Aggregates Using an Orthogonal Array Table and Analysis by Machine Learning
por: Wie, Young Min, et al.
Publicado: (2020)

Modeling and Machine Learning of Vibration Amplitude and Surface Roughness after Waterjet Cutting
por: Leleń, Michał, et al.
Publicado: (2023)

Photonic machine learning with on-chip diffractive optics
por: Fu, Tingzhao, et al.
Publicado: (2023)

Cutting Forces Assessment in CNC Machining Processes: A Critical Review
por: Sousa, Vitor F. C., et al.
Publicado: (2020)

Improving the Performance of Steel Machining Processes through Cutting by Vibration Control
por: Oleksik, Mihaela, et al.
Publicado: (2021)

Cutting of Five PbWO4 Crystals on the CERN Prototype Cutting Machine
por: De Forni, Armando, et al.
Publicado: (1997)

Determination of the Tool–Chip Contact Length for the Cutting Processes
por: Storchak, Michael, et al.
Publicado: (2022)

Multi-objective cutting parameter optimization model of multi-pass turning in CNC machines for sustainable manufacturing
por: Pangestu, Phengky, et al.
Publicado: (2021)

Surface Finish and Residual Stresses Induced by Orthogonal Dry Machining of AA7075-T651
por: Jomaa, Walid, et al.
Publicado: (2014)

Cannot write session to /tmp/vufind_sessions/sess_kukmjmti6j5kmupsle85e2sm19