Cargando…

Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses

Wire arc additive manufacturing (WAAM) is an additive manufacturing process based on the arc welding process in which wire is melted by an electric arc and deposited layer by layer. Due to the cost and rate benefits over powder-based additive manufacturing technologies and other alternative heat sou...

Descripción completa

Detalles Bibliográficos
Autores principales:	Rani, Kasireddy Usha, Kumar, Rajiv, Mahapatra, Manas M., Mulik, Rahul S., Świerczyńska, Aleksandra, Fydrych, Dariusz, Pandey, Chandan
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2022
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC9604903/ https://www.ncbi.nlm.nih.gov/pubmed/36295161 http://dx.doi.org/10.3390/ma15207094

Ejemplares similares

Autogenous Fiber Laser Welding of 316L Austenitic and 2304 Lean Duplex Stainless Steels
por: Landowski, Michał, et al.
Publicado: (2020)

Microstructure Evolution and Mechanical Properties of a Wire-Arc Additive Manufactured Austenitic Stainless Steel: Effect of Processing Parameter
por: Long, Ping, et al.
Publicado: (2021)

Austenitic stainless steels: microstructure and mechanical properties
por: Marshall, Patrick
Publicado: (1984)

Non-oxide precipitates in additively manufactured austenitic stainless steel
por: Upadhyay, Manas Vijay, et al.
Publicado: (2021)

Effect of B on Microstructure and Properties of Surfacing Layer of Austenitic Stainless Steel Flux Cored Wire
por: Guo, Jianbo, et al.
Publicado: (2022)

Technical spécification. Manufacture of austenitic stainless-steel tubular elbows
por: CERN. Geneva
Publicado: (1988)

Mechanical Properties of Austenitic Stainless Steel Made by Additive Manufacturing
por: Luecke, William E, et al.
Publicado: (2014)

Electrochemical Polishing of Austenitic Stainless Steels
por: Łyczkowska-Widłak, Edyta, et al.
Publicado: (2020)

Microstructure and Pitting Corrosion of Austenite Stainless Steel after Crack Arrest
por: Zhang, Zhuwu, et al.
Publicado: (2019)

Steel forgings for pressure purposes - Part 5: martensitic, austenitic and austenitic-ferritic stainless steels
por: Association Française de Normalisation. Paris
Publicado: (2000)

Fabricating Pyramidal Lattice Structures of 304 L Stainless Steel by Wire Arc Additive Manufacturing
por: Zhang, Haorui, et al.
Publicado: (2020)

Wire + Arc Additive Manufacturing and Heat Treatment of Super Martensitic Stainless Steel with a Refined Microstructure and Excellent Mechanical Properties
por: Zou, Xiaodong, et al.
Publicado: (2022)

The Microstructure and Mechanical Properties of Multi-Strand, Composite Welding-Wire Welded Joints of High Nitrogen Austenitic Stainless Steel
por: Li, Jianguo, et al.
Publicado: (2019)

Microstructure Evolution at Ni/Fe Interface in Dissimilar Metal Weld between Ferritic Steel and Austenitic Stainless Steel
por: Li, Xiaogang, et al.
Publicado: (2023)

Microstructure and Properties of ER50-6 Steel Fabricated by Wire Arc Additive Manufacturing
por: Hu, Qingxian, et al.
Publicado: (2021)

Influence of the Interlayer Temperature on Structure and Properties of Wire and Arc Additive Manufactured Duplex Stainless Steel Product
por: Knezović, Nikola, et al.
Publicado: (2020)

Flow and fracture of austenitic stainless steels at cryogenic temperatures
por: Fernández-Pisón, P, et al.
Publicado: (2021)

Tritium in austenitic stainless steel vessels: the integrity of the vessel
por: Ells, C E
Publicado: (1980)

Corrosion Susceptibility and Allergy Potential of Austenitic Stainless Steels
por: Reclaru, Lucien, et al.
Publicado: (2020)

Effect of tungsten on the oxidation of alumina-forming austenitic stainless steel
por: Kang, Jun-Yun, et al.
Publicado: (2019)

Peculiarities of DRX in a Highly-Alloyed Austenitic Stainless Steel
por: Dolzhenko, Pavel, et al.
Publicado: (2021)

Constitutive Model of the Surface Roughening Behavior of Austenitic Stainless Steel
por: Aziz, Abdul, et al.
Publicado: (2022)

Influence of PWHT Parameters on the Mechanical Properties and Microstructural Behavior of Multi-Pass GTAW Joints of P92 Steel
por: Sirohi, Sachin, et al.
Publicado: (2022)

Study on Microstructural Characterization, Mechanical Properties and Residual Stress of GTAW Dissimilar Joints of P91 and P22 Steels
por: Sauraw, Anupam, et al.
Publicado: (2021)

Case Study of the Tensile Fracture Investigation of Additive Manufactured Austenitic Stainless Steels Treated at Cryogenic Conditions
por: Bidulský, Róbert, et al.
Publicado: (2020)

Quantitative 3D Characterization for Kinetics of Corrosion Initiation and Propagation in Additively Manufactured Austenitic Stainless Steel
por: Li, Jianli, et al.
Publicado: (2022)

Effect of Rolling Temperature on Microstructure Evolution and Mechanical Properties of AISI316LN Austenitic Stainless Steel
por: Xiong, Yi, et al.
Publicado: (2018)

The Effect of Service on Microstructure and Mechanical Properties of HR3C Heat-Resistant Austenitic Stainless Steel
por: Golański, Grzegorz, et al.
Publicado: (2020)

Microstructure, Mechanical, and Corrosion Properties of Ni-Free Austenitic Stainless Steel Prepared by Mechanical Alloying and HIPping
por: Romanczuk, Eliza, et al.
Publicado: (2019)

Gradient Microstructure and Texture Formation in a Metastable Austenitic Stainless Steel during Cold Rotary Swaging
por: Panov, Dmitrii, et al.
Publicado: (2023)

Processing of a Martensitic Tool Steel by Wire-Arc Additive Manufacturing
por: Ziesing, Ulf, et al.
Publicado: (2022)

Decarburization of Wire-Arc Additively Manufactured ER70S-6 Steel
por: Aprilia, Aprilia, et al.
Publicado: (2023)

Flow and fracture of austenitic stainless steels at cryogenic temperatures: experiments and modeling.
por: Fernandez Pison, Pilar
Publicado: (2023)

Superior Strength and Ductility of 304 Austenitic Stainless Steel with Gradient Dislocations
por: Pan, Qingsong, et al.
Publicado: (2021)

Resistance of Aluminide Coatings on Austenitic Stainless Steel in a Nitriding Atmosphere
por: Wierzbowska, Karolina, et al.
Publicado: (2021)

High Temperature Fatigue of Aged Heavy Section Austenitic Stainless Steels
por: Wärner, Hugo, et al.
Publicado: (2021)

Corrosion behavior of 904L austenitic stainless steel in hydrofluoric acid
por: Zou, Guobo, et al.
Publicado: (2018)

Research Progress of Alumina-Forming Austenitic Stainless Steels: A Review
por: Liu, Ling, et al.
Publicado: (2022)

Effect of Copper Addition on the Formability of 304L Austenitic Stainless Steel
por: Huang, Ali, et al.
Publicado: (2022)

Effect of Cu on the Formation of Reversed Austenite in Super Martensitic Stainless Steel
por: Jiang, Wen, et al.
Publicado: (2023)

Cannot write session to /tmp/vufind_sessions/sess_pdanu8cofr7hus3q7e9t5poo14