Cargando…

Cold Roll Forming Process Design for Complex Stainless-Steel Section Based on COPRA and Orthogonal Experiment

Cold roll forming can fabricate products with complex profiles, and its parameter optimization can achieve high quality and improved precision of products. In this paper, taking the side shield as a typical product, the cold roll forming of a complex section of stainless steel SUS301L-ST is analyzed...

Descripción completa

Detalles Bibliográficos
Autores principales:	Wang, Jing, Liu, Hua-Min, Li, She-Fei, Chen, Wan-Jun
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2022
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC9697423/ https://www.ncbi.nlm.nih.gov/pubmed/36431510 http://dx.doi.org/10.3390/ma15228023

Ejemplares similares

Forming Quality Analysis on the Cold Roll Forming C-channel Steel
por: Hui, Xiangjun, et al.
Publicado: (2018)

Optimization of the Forming Method on Torsion Defect in Cold-Roll Forming of Z Section Steel
por: Wang, Yesong, et al.
Publicado: (2022)

Superficial Grain Refinement of 316L Stainless Steel by Rolling with Rough Rolls
por: Maril, Yasmin, et al.
Publicado: (2023)

On the Strength of a 316L-Type Stainless Steel Subjected to Cold or Warm Rolling Followed by Annealing
por: Odnobokova, Marina, et al.
Publicado: (2020)

Numerical Prediction of Microstructure Evolution of Small-Diameter Stainless Steel Balls during Cold Skew Rolling
por: Zhou, Jing, et al.
Publicado: (2023)

Effect of Solutionizing Duration and Temperature on the Electrochemical Corrosion and Pitting Resistance of Cold-Rolled Super Austenitic Stainless Steel
por: Adesina, Akeem Yusuf, et al.
Publicado: (2022)

Dataset showing steel cold rolling process parameters for a 6-high cold rolling mill in Nigeria
por: Ayuba, Emmanuel O., et al.
Publicado: (2018)

Evolution of Grain Interfaces in Annealed Duplex Stainless Steel after Parallel Cross Rolling and Direct Rolling
por: Wang, Ming, et al.
Publicado: (2018)

The Effect of Ni Interlayer on the Hot-Rolled and Quenched Stainless Steel Clad Plate
por: Lin, Zengmeng, et al.
Publicado: (2020)

Designing Inorganic Semiconductors with Cold‐Rolling Processability
por: Wang, Xu‐Dong, et al.
Publicado: (2022)

Effect of Cold-Rolling Reduction on Recrystallization Microstructure, Texture and Corrosion Properties of the X2CrNi12 Ferritic Stainless Steel
por: Li, Rui, et al.
Publicado: (2022)

Proposal for the award of a contract for the supply of rolled and forged round bars in stainless steel
Publicado: (2017)

Statistical Research of Stainless Austenitic Steel Grain Size Distribution after Screw Rolling
por: Skripalenko, Mikhail Mikhailovich, et al.
Publicado: (2020)

Effect of Reduction Sequence during Rolling on Deformed Texture and Anisotropy of Ferritic Stainless Steel
por: Cho, Sang Heon, et al.
Publicado: (2023)

Microstructure and Mechanical Properties of Hot- Rolled and Cold-Rolled Medium-Mn TRIP Steels
por: Liu, Chunquan, et al.
Publicado: (2018)

Stainless steels
por: Davis, J R
Publicado: (1994)

Effect of the Forming Zone Length on Helical Rolling Processes for Manufacturing Steel Balls
por: Gontarz, Andrzej, et al.
Publicado: (2019)

Energy values of copra meal and cornstarch for broiler chickens
por: Haetinger, Vítor S., et al.
Publicado: (2020)

Numerical Simulation and Experimental Investigation of Cold-Rolled Steel Cutting
por: Kaczmarczyk, Jarosław, et al.
Publicado: (2018)

An Experimental Investigation of Steel Surface Topography Transfer by Cold Rolling
por: Xu, Dong, et al.
Publicado: (2020)

Modelling of Guillotine Cutting of a Cold-Rolled Steel Sheet
por: Kaczmarczyk, Jarosław
Publicado: (2019)

Effect of tungsten on the oxidation of alumina-forming austenitic stainless steel
por: Kang, Jun-Yun, et al.
Publicado: (2019)

Microstructure and Mechanical Properties of 4Al Alumina-Forming Austenitic Steel after Cold-Rolling Deformation and Annealing
por: Jiang, Chenchen, et al.
Publicado: (2020)

Effect of Rolling Temperature on Microstructure Evolution and Mechanical Properties of AISI316LN Austenitic Stainless Steel
por: Xiong, Yi, et al.
Publicado: (2018)

Comparison between Mechanical Properties and Structures of a Rolled and a 3D-Printed Stainless Steel
por: Natali, Stefano, et al.
Publicado: (2019)

Creation of 3D Model of Stainless-Steel Billet’s Grain after Three-High Screw Rolling
por: Skripalenko, Mikhail Mikhailovich, et al.
Publicado: (2022)

Hierarchical Multiple Precursors Induced Heterogeneous Structures in Super Austenitic Stainless Steels by Cryogenic Rolling and Annealing
por: Tan, Duo, et al.
Publicado: (2023)

Corrosion of stainless steels /
por: Sedriks, A. John
Publicado: (1996)

Corrosion of stainless steels
por: Sedriks, A John
Publicado: (1996)

Research Progress of Alumina-Forming Austenitic Stainless Steels: A Review
por: Liu, Ling, et al.
Publicado: (2022)

The comparison of frictional resistance in titanium, self-ligating stainless steel, and stainless steel brackets using stainless steel and TMA archwires: An in vitro study
por: Khalid, Syed Altaf, et al.
Publicado: (2012)

Review on Cold-Formed Steel Connections
por: Lee, Yeong Huei, et al.
Publicado: (2014)

The Research of the Rolling Speed Influence on the Mechanism of Strip Breaks in the Steel Rolling Process
por: Rusnák, Ján, et al.
Publicado: (2020)

Voids healing and carbide refinement of cold rolled M50 bearing steel by electropulsing treatment
por: Wang, Feng, et al.
Publicado: (2019)

Strengthening of 0.18 wt % C Steel by Cold Differential Speed Rolling
por: Kang, Jee-Hyun, et al.
Publicado: (2022)

Microstructural Evolution of SK85 Pearlitic Steel Deformed by Heavy Cold Rolling
por: Yang, Cai-Ding, et al.
Publicado: (2022)

Effect of Cold Rolling Process on Microstructure, Texture and Properties of Strip Cast Fe-2.6%Si Steel
por: Xu, Yunbo, et al.
Publicado: (2018)

Application of Extended Finite Element Method for Studying Crack Propagation of Welded Strip Steel in the Cold Rolling Process
por: Chen, Jianjun, et al.
Publicado: (2023)

Design considerations in the use of stainless steel for vacuum and cryogenic equipment
por: Geyari, C
Publicado: (1976)

A Novel Design for Improving the Control on the Stainless-Steel Vessel Welding Process for Superconducting Magnets
por: Vallone, G, et al.
Publicado: (2022)

Cannot write session to /tmp/vufind_sessions/sess_7cd67ogjekuvvf9fvmnja2mviv