Cargando…

Multi-Objective Optimization of Process Parameters during Micro-Milling of Nickel-Based Alloy Inconel 718 Using Taguchi-Grey Relation Integrated Approach

This research investigates the machinability of Inconel 718 under conventional machining speeds using three different tool coatings in comparison with uncoated tool during milling operation. Cutting speed, feed rate and depth of cut were selected as variable machining parameters to analyze output re...

Descripción completa

Detalles Bibliográficos
Autores principales:	Sheheryar, Muhammad, Khan, Muhammad Ali, Jaffery, Syed Husain Imran, Alruqi, Mansoor, Khan, Rehan, Bashir, M. Nasir, Petru, Jana
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2022
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC9736743/ https://www.ncbi.nlm.nih.gov/pubmed/36499794 http://dx.doi.org/10.3390/ma15238296

Ejemplares similares

Statistical Analysis of Surface Roughness, Burr Formation and Tool Wear in High Speed Micro Milling of Inconel 600 Alloy under Cryogenic, Wet and Dry Conditions
por: Baig, Amjad, et al.
Publicado: (2022)

Deformation Analysis of Continuous Milling of Inconel718 Nickel-Based Superalloy
por: Li, Xueguang, et al.
Publicado: (2022)

Milling Mechanism and Chattering Stability of Nickel-Based Superalloy Inconel 718
por: Zheng, Jin, et al.
Publicado: (2023)

Cutting Forces during Inconel 718 Orthogonal Turn-Milling
por: Felusiak-Czyryca, Agata, et al.
Publicado: (2021)

A Study on the Optimal Machining Parameters of the Induction Assisted Milling with Inconel 718
por: Kim, Eun Jung, et al.
Publicado: (2019)

Optimization of Cutting Process Parameters in Inclined Drilling of Inconel 718 Using Finite Element Method and Taguchi Analysis
por: Pervaiz, Salman, et al.
Publicado: (2020)

Selective Anisotropy of Mechanical Properties in Inconel718 Alloy
por: Liang, Yu, et al.
Publicado: (2021)

Comparison of Flank Super Abrasive Machining vs. Flank Milling on Inconel(®) 718 Surfaces
por: González, Haizea, et al.
Publicado: (2018)

Statistical Analysis of Machining Parameters on Burr Formation, Surface Roughness and Energy Consumption during Milling of Aluminium Alloy Al 6061-T6
por: Zaidi, Sajid Raza, et al.
Publicado: (2022)

Investigation into the Microstructure and Hardness of Additively Manufactured (3D-Printed) Inconel 718 Alloy
por: Kurdi, Abdulaziz, et al.
Publicado: (2023)

Parametric Optimization of Laser Additive Manufacturing of Inconel 625 Using Taguchi Method and Grey Relational Analysis
por: Yang, Bo, et al.
Publicado: (2020)

Experimental Investigation of Principal Residual Stress and Fatigue Performance for Turned Nickel-Based Superalloy Inconel 718
por: Hua, Yang, et al.
Publicado: (2018)

Temperature-Based Prediction of Joint Hardness in TIG Welding of Inconel 600, 625 and 718 Nickel Superalloys
por: Jamrozik, Wojciech, et al.
Publicado: (2021)

Temperature Measurement and Numerical Prediction in Machining Inconel 718
por: Díaz-Álvarez, José, et al.
Publicado: (2017)

Study on the Effects of Different Cutting Angles on the End-Milling of Wire and Arc Additive Manufacturing Inconel 718 Workpieces
por: dos Santos, Gustavo Quadra Vieira, et al.
Publicado: (2022)

Anomalies in the Geometric Surface Structure of Shaped Elements Composed of Inconel 718 Alloy
por: Krawczyk, Bartłomiej, et al.
Publicado: (2021)

Fretting wear behavior of Inconel 718 alloy manufactured by DED and treated by UNSM
por: Li, Chao, et al.
Publicado: (2023)

Experimental Study of Direct Laser Deposition of Ti-6Al-4V and Inconel 718 by Using Pulsed Parameters
por: Shah, Kamran, et al.
Publicado: (2014)

Thermomechanical Process Simulation and Experimental Verification for Laser Additive Manufacturing of Inconel(®)718
por: Zafar, Muhammad Qasim, et al.
Publicado: (2023)

Corrigendum to “Experimental Study of Direct Laser Deposition of Ti-6Al-4V and Inconel 718 by Using Pulsed Parameters”
por: Shah, Kamran, et al.
Publicado: (2015)

Achieving the Minimum Roughness of Laser Milled Micro-Impressions on Ti 6Al 4V, Inconel 718, and Duralumin
por: Ahmed, Naveed, et al.
Publicado: (2020)

Laser Metal Deposition of Inconel 718 Alloy and As-built Mechanical Properties Compared to Casting
por: Mazzucato, Federico, et al.
Publicado: (2021)

Impact of Notches on Additively Manufactured Inconel 718 Tensile Performance
por: Johnson, Joseph, et al.
Publicado: (2023)

Influence of Heat Treatment on Cyclic Response of Nickel-Based Superalloy Inconel 718 up to Very-High Cycle Regime
por: Zhao, Mengxiong, et al.
Publicado: (2020)

Method of Data Selection for Turning of Inconel 718 Alloy Obtained by Casting and Laser Sintering Powder
por: Latosińska, Ksenia, et al.
Publicado: (2022)

Grain Refinement of Inconel 718 Superalloy—The Effect of Rotating Magnetic Field
por: Silva, Rui Pedro, et al.
Publicado: (2022)

Measuring the effect of residual stress on the machined subsurface of Inconel 718 by nanoindentation
por: Chen, Ling, et al.
Publicado: (2021)

In Envelope Additive/Subtractive Manufacturing and Thermal Post-Processing of Inconel 718
por: Atabay, Sila Ece, et al.
Publicado: (2022)

Surface Topography Description of Threads Made with Turning on Inconel 718 Shafts
por: Krawczyk, Bartłomiej, et al.
Publicado: (2022)

High temperature performance of wire-arc additive manufactured Inconel 718
por: James, William Sean, et al.
Publicado: (2023)

Simulation of Work Hardening in Machining Inconel 718 with Multiscale Grain Size
por: Zhuang, Kejia, et al.
Publicado: (2023)

Laser Beam Drilling of Inconel 718 and Its Effect on Mechanical Properties Determined by Static Uniaxial Tensile Testing at Room and Elevated Temperatures
por: Petrů, Jana, et al.
Publicado: (2021)

Effect of Layer-Wise Varying Parameters on the Microstructure and Soundness of Selective Laser Melted INCONEL 718 Alloy
por: Wang, Xiang, et al.
Publicado: (2019)

Enhancing Mechanical Properties of the Spark Plasma Sintered Inconel 718 Alloy by Controlling the Nano-Scale Precipitations
por: Yan, Shuaijiang, et al.
Publicado: (2019)

Pulsed Laser Spot Welding Thermal-Shock-Induced Microcracking of Inconel 718 Thin Sheet Alloy
por: Shi, Mingli, et al.
Publicado: (2023)

Study of the Influence of Shielding Gases on Laser Metal Deposition of Inconel 718 Superalloy
por: Ruiz, Jose Exequiel, et al.
Publicado: (2018)

An Investigation of Surface Corrosion Behavior of Inconel 718 after Robotic Belt Grinding
por: Wang, Junwei, et al.
Publicado: (2018)

Analysis of the Machining Process of Inconel 718 Parts Manufactured by Laser Metal Deposition
por: Ostra, Txomin, et al.
Publicado: (2019)

Investigation of the Machinability of the Inconel 718 Superalloy during the Electrical Discharge Drilling Process
por: Machno, Magdalena
Publicado: (2020)

Magnesium Reinforced with Inconel 718 Particles Prepared Ex Situ—Microstructure and Properties
por: Trojanová, Zuzanka, et al.
Publicado: (2020)

Cannot write session to /tmp/vufind_sessions/sess_7g3dj3jdm81vc1cbh9u5b5ll4k