Cargando…

Simulation-Assisted Process Design and Experimental Verification of Laterally Confined Oxide Areas Generated with Continuous Electrolytic Free Jet on EN AW-7075 Aluminum Alloy

Local anodization with a free electrolyte jet is a suitable solution for locally confined surface functionalization without additionally required preparation of the parts. However, the geometrical formation of the anodic oxide layer in jet-based anodization is not yet sufficiently understood. In thi...

Descripción completa

Detalles Bibliográficos
Autores principales:	Quitzke, Susanne, Danilov, Igor, Martin, André, Morgenstern, Roy, Lampke, Thomas, Schubert, Andreas
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2023
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC9965328/ https://www.ncbi.nlm.nih.gov/pubmed/36837993 http://dx.doi.org/10.3390/mi14020293

Ejemplares similares

Measurements of Forces and Selected Surface Layer Properties of AW-7075 Aluminum Alloy Used in the Aviation Industry after Abrasive Machining
por: Matuszak, Jakub, et al.
Publicado: (2019)

Microstructure and Properties of Electroless Ni-P/Si(3)N(4) Nanocomposite Coatings Deposited on the AW-7075 Aluminum Alloy
por: Czapczyk, Kazimierz, et al.
Publicado: (2021)

Microstructure Evolution of 7075 Aluminum Alloy by Rotary
por: Cao, Hui, et al.
Publicado: (2022)

Tribological Properties of Ni-P/Si(3)N(4) Nanocomposite Layers Deposited by Chemical Reduction Method on Aluminum Alloy AW-7075
por: Czapczyk, Kazimierz
Publicado: (2020)

Study of Corrosion, Structural, and Mechanical Properties of EN AW-6082 and EN AW-7075 Welded Joints
por: Wojdat, Tomasz, et al.
Publicado: (2021)

Microstructure Control and Performance Evolution of Aluminum Alloy 7075 by Nano-Treating
por: Zuo, Min, et al.
Publicado: (2019)

Corrosion Fatigue Fracture Characteristics of FSW 7075 Aluminum Alloy Joints
por: Ma, Qingna, et al.
Publicado: (2020)

Dynamic ESPI Evaluation of Deformation and Fracture Mechanism of 7075 Aluminum Alloy
por: Takahashi, Shun, et al.
Publicado: (2021)

The Study on the Overall Plasma Electrolytic Oxidation for 6061–7075 Dissimilar Aluminum Alloy Welded Parts Based on the Dielectric Breakdown Theory
por: Chen, Yanfei, et al.
Publicado: (2018)

Research on the Influence of the AW 5754 Aluminum Alloy State Condition and Sheet Arrangements with AW 6082 Aluminum Alloy on the Forming Process and Strength of the ClinchRivet Joints
por: Mucha, Jacek, et al.
Publicado: (2021)

Improving Mechanical Properties of PVPPA Welded Joints of 7075 Aluminum Alloy by PWHT
por: Li, Guowei, et al.
Publicado: (2018)

Nanoparticle-enabled phase control for arc welding of unweldable aluminum alloy 7075
por: Sokoluk, Maximilian, et al.
Publicado: (2019)

Deformation Behavior and Properties of 7075 Aluminum Alloy under Electromagnetic Hot Forming
por: Du, Zhihao, et al.
Publicado: (2021)

Liquation Cracking Susceptibility and Mechanical Properties of 7075 Aluminum Alloy GTAW Joints
por: Li, Zhuoxin, et al.
Publicado: (2022)

Prediction of Fatigue Crack Initiation of 7075 Aluminum Alloy by Crystal Plasticity Simulation
por: Shiraiwa, Takayuki, et al.
Publicado: (2023)

Soldering of 7075 Aluminum Alloy Using Ni-P and Cu-Cr Electrodeposited Interlayers
por: Mirski, Zbigniew, et al.
Publicado: (2020)

Numerical Simulation and Experimental Study on the Drilling Process of 7075-t6 Aerospace Aluminum Alloy
por: Luo, Haitao, et al.
Publicado: (2021)

Evolution of Microstructure and Properties of Air-Cooled Friction-Stir-Processed 7075 Aluminum Alloy
por: Iwaszko, Józef, et al.
Publicado: (2022)

Tensile Property of 7075 Aluminum Alloy with Strengthening Layer by Laser Remelting-Cladding Treatment
por: Sui, Qi, et al.
Publicado: (2023)

Investigation of Thermophysical Properties of AW-2024-T3 Bare and Clad Aluminum Alloys
por: Zmywaczyk, Janusz, et al.
Publicado: (2020)

Effect of Load on the Corrosion Behavior of Friction Stir Welded AA 7075-T6 Aluminum Alloy
por: Cabrini, Marina, et al.
Publicado: (2020)

Research on High Temperature Stamping Forming Performance and Process Parameters Optimization of 7075 Aluminum Alloy
por: Ma, Zheng, et al.
Publicado: (2021)

Microstructure and Mechanical Properties of AA7075 Aluminum Alloy Fabricated by Spark Plasma Sintering (SPS)
por: Soares, Elder, et al.
Publicado: (2021)

Increasing the Mechanical Strength and Corrosion Resistance of Aluminum Alloy 7075 via Hydrostatic Extrusion and Aging
por: Orłowska, Marta, et al.
Publicado: (2022)

Effect of Reticulate Unit Spacing on Microstructure and Properties of Biomimetic 7075 Aluminum Alloy by Laser Cladding
por: Sui, Qi, et al.
Publicado: (2023)

Influence of Cutting-Edge Microgeometry on Cutting Forces in High-Speed Milling of 7075 Aluminum Alloy
por: Żyłka, Łukasz, et al.
Publicado: (2023)

Impact of Marine Atmospheric Corrosion on the Microstructure and Tensile Properties of 7075 High-Strength Aluminum Alloy
por: Xiang, Lin, et al.
Publicado: (2023)

Cavitation Erosion Characteristics of the EN AW-6082 Aluminum Alloy by TIG Surface Remelting
por: Mitelea, Ion, et al.
Publicado: (2023)

A New Infrared Heat Treatment on Hot Forging 7075 Aluminum Alloy: Microstructure and Mechanical Properties
por: Chang, Yi-Ling, et al.
Publicado: (2020)

The Effect of Direct Electric Current on the Plastic Behavior of AA7075 Aluminum Alloy in Different States of Hardening
por: Dobras, Daniel, et al.
Publicado: (2020)

Long-Term Atmospheric Corrosion Behavior of Epoxy Prime Coated Aluminum Alloy 7075-T6 in Coastal Environment
por: Zhang, Sheng, et al.
Publicado: (2018)

Electric Arc Furnace Dust Recycled in 7075 Aluminum Alloy Composites Fabricated by Spark Plasma Sintering (SPS)
por: Soares, Elder, et al.
Publicado: (2022)

Influence of Scanning Strategies on Processing of Aluminum Alloy EN AW 2618 Using Selective Laser Melting
por: Koutny, Daniel, et al.
Publicado: (2018)

Intensification of Electrochemical Performance of AA7075 Aluminum Alloys Using Rare Earth Functionalized Water-Based Polymer Coatings
por: Ferrel-Álvarez, Atzin C., et al.
Publicado: (2017)

Optimization of Process Parameters in CNC Turning of Aluminum 7075 Alloy Using L27 Array-Based Taguchi Method
por: Akhtar, Mohammad Nishat, et al.
Publicado: (2021)

Developing Fused Deposition Modeling Additive Manufacturing Processing Strategies for Aluminum Alloy 7075: Sample Preparation and Metallographic Characterization
por: Ding, Huan, et al.
Publicado: (2022)

Study on Microstructure Evolution Mechanism of Gradient Structure Surface of AA7075 Aluminum Alloy by Ultrasonic Surface Rolling Treatment
por: Fu, Lei, et al.
Publicado: (2023)

Process Optimization, Morphology, Structure, and Adhesive Strength of Electrodeposited Ni–Fe–Graphene Composite Coating on the 7075 Aluminum Alloy
por: Li, Na, et al.
Publicado: (2023)

Corrosion behaviour of 7075 aluminium alloy in acidic solution
por: Kwolek, Przemysław
Publicado: (2020)

Surface Characterizations of Fretting Fatigue Damage in Aluminum Alloy 7075-T6 Clamped Joints: The Beneficial Role of Ni–P Coatings
por: Oskouei, Reza H., et al.
Publicado: (2016)

Cannot write session to /tmp/vufind_sessions/sess_g1mfs9b06hboe67lhq5ucg0ao7