“…Section 3 describes the technology of the chamber construction. The results of the ANSYS calculation of the cathode planes possible deformations are presented in Section 4. …”
Enlace del recurso

“…These values have been compared withdetailed simulations using ANSYS and Garfield++. Within the scope ofthis study, a large impact of space-charges on the ion backflow hasbeen observed. …”
Enlace del recurso
Enlace del recurso

“…The geometries of 14 patients (28 vessels) were reconstructed using Mimics and Geomagic Studio software from CT angiography (CTA). ANSYS ICEM and ANSYS FLUENT were utilized for mesh generation, set boundary conditions, solve governing equations, and perform numerical simulations. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Test results of the stress distribution in the structure and the in dummy coil is reported and compared with expected results calculated with the structural analysis program ANSYS.…”
Enlace del recurso
Enlace del recurso

“…The FEA is done using the Explicit Dynamics (AutoDyn) module of ANSYS Workbench and for experimentation Drop Test Machine (DTM) is used. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Von Mises stresses and deformation generated were compared using ANSYS Workbench 17.0 and finite element software. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Therefore, a modeling analysis and lightweight design based on ANSYS for axle hub is proposed. Firstly, design dimensions and structural parameters of axle hub are modeled. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The addition of random defects for the overall and the component units was achieved by integrating Matlab R2022a and Ansys R19.0 finite element software. Nonlinear analysis was conducted to calculate ultimate load factors and nodal ultimate displacements of the materials under various random defects at each stage of construction. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…To create a solid model of the implant and bone and to carry out the FE analysis, the ANSYS V.12 programme was used. RESULTS: The findings indicated that the neck of dental implants is the area of highest stress for all implant diameters and lengths, with an increase in implant length from 10 mm to 12 mm resulting in a slight raise in stress at the interface of implant-bone, and an increase in diameter from 3.75 mm to 4.25 mm having no appreciable impact on the value of stresses around dental implants. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…An electromagnetic–temperature coupling model was constructed using ANSYS to study the temperature and electromagnetic field distribution during the forming process. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…MATERIALS AND METHODS: A mandibular premolar was modeled using the ANSYS software program. Two models were created to represent circular and oval fiber posts in this tooth model. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…To solve the problem of wheel/rail rolling contact of nonlinear steady-state curving, a three-dimensional transient finite element (FE) model is developed by the explicit software ANSYS/LS-DYNA. To improve the solving speed and efficiency, an explicit–explicit order solution method is put forward based on analysis of the features of implicit and explicit algorithm. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The results obtained using these different versions of the LB-based code will then be validated with ANSYS FLUENT, a commercially available finite volume- (FV-) based CFD solver. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The model was imported into ANSYS 15.0 FE analysis software. Ligaments were added. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The effect of gauge pattern was evaluated with ANSYS simulations. The piezoresistance of the strain gauges was measured and the gauge factor determined. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The hydrodynamics of secondary flow phenomena in a disc‐shaped gas vortex unit (GVU) is investigated using experimentally validated numerical simulations. The simulation using ANSYS FLUENT(®) v.14a reveals the development of a backflow region along the core of the central gas exhaust, and of a counterflow multivortex region in the bulk of the disc part of the unit. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…By using the computational fluid dynamics software Fluent 18.0 (ANSYS), the drag force and the drag coefficient of different conical micromotors are calculated. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Furthermore, the reliability of the model was validated by the ANSYS simulation results and the experimental results. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…This article addresses the study of crack behavior elicited on axial fatigue in specimens joined by butt weld made of steel ASTM A36 by using fracture mechanics and simulation software of finite elements (Ansys APDL, Franc3D). The computational model was initially to define the geometry model by using CAD software. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Finite element analysis software ANSYS WORKBENCH is used to carry out all the simulations.…”
Enlace del recurso
Enlace del recurso
Enlace del recurso