“…Cavities are made of copper and sputtered niobium. We build an ANSYS model to model thermal distributions and heat flows in the cavity structure. …”
Enlace del recurso

“…Chapters in this experimental handbook are presented in two parts with the goal of equipping readers with the information necessary to study and determine key factors which affect the performance of the solar chimney power plant.In the first part, the authors present a simulation developed by using computational fluid dynamics (CFD) modeling software ANSYS Fluent to model the airflow. The adopted CFD models include k-ɛ turbulence model, the DO radiation model and the convection heat flux transfer model. …”
Enlace del recurso

“…This paper summarises the correlation between the temperature measured as a function of the energy deposited and the same temperatures computed in a numerical model combining FLUKA and ANSYS simulations. The goal of this study is the assessment of the thermal contact quality between the beam absorbing blocks and the copper jacket, by analysing the cooling times observed from the measurements and from the thermo-mechanical simulations. …”
Enlace del recurso

“…The beam dump, made of graphite, has been designed using two different codes, the Monte Carlo code GEANT4 to simulate the energy deposition and ANSYS used to simulate the thermal resistance of the graphite due to the long pulse duration. …”
Enlace del recurso
Enlace del recurso

“…In this paper, the multiphysics problem of quench propagation in Nb$_{3}$Sn cables is addressed under adiabatic conditions by means of a set of analytical formulae and several finite element models with different level of complexity in ANSYS APDL, COMSOL Multiphysics, and MATLAB. These models are aimed at describing the conductor behavior in terms of HST and QPV observed during the training of racetrack coils at SM18.…”
Enlace del recurso
Enlace del recurso

“…Moreover the status of numerical simulations using FLUKA and multi-physics FEM code (ANSYS) to assess the different effect and the irradiation of the proposed experimental setup in preparation of the test is shown.…”
Enlace del recurso
Enlace del recurso

“…In the current study, a FEM-based representative volume element (RVE) technique is used to evaluate the elastic modulus of recycled high-density polyethylene (rHDPE) filled spherical-shaped shaped silicon carbide (SiC). In the ANSYS 2019, the material designer (MD) module is used to generate a 3D RVE of 500 × 500 × 500 μm cuboid, with randomly dispersed spherical SiC particles (i.e., 10, 15, 20, and 30% volume fractions) inside rHDPE. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The FE foot–shoe model was built in ANSYS using computed-tomography imaging data. Static structural analysis was used to simulate the moment of running push and stretch. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The finite element analysis of a variable section cantilever beam with ANSYS shows that the linear model’s relative deviation is as high as 6% at 5000 με, while the relative deviation of the nonlinear model is only 0.2%. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Employing specialized software for numerical analysis, such as ANSYS-AUTODYN 2022R1(®), the interaction of shock waves with a protection structure has been studied. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…In this study, a (220)Rn calibration chamber was designed and developed at the Institute of Radiochemistry and Radioecology (RRI) based on the computational fluid dynamics (CFD) method implemented in ANSYS Fluent 2020 R1 code at the University of Pannonia in Hungary. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…SolidWorks software is used for modeling; ANSYS software is used for finite element analysis. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The mechanical characteristics of the produced PLA composite specimens were measured experimentally, while the ANSYS model was established to identify the composites’ load-carrying capacity. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The designed piezoelectric vibrator is composed of a rhombic micro displacement amplifier, counterweight blocks and two piezoelectric stacks with low-voltage drive and a large output displacement. ANSYS software (Workbench 19.0) simulation results show that at the natural frequency of 946 Hz, the designed piezoelectric vibrator will produce the maximum output displacement. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Therefore, simulator-based virtual testing has gained traction over the years as the preferred testing method due to its low cost, efficiency, and effectiveness in executing a wide range of testing scenarios. Companies like ANSYS and NVIDIA have come up with robust simulators, and open-source simulators such as CARLA have also populated the market. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…This paper presents a statistically optimized design with a high number of the design variables to reduce the weight of the electromagnet under the constraint of normal force using response surface methodology (RSM) and the kriging interpolation method. 2D and 3D magnetostatic analysis of the electromagnet are performed using ANSYS. The most effective design variables are extracted by a Pareto chart. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Secondly, the thermal-modal model of the cylinder resonator with several defects such as mass imbalance, frequency split (FS), and geometry errors are developed by ANSYS. Simulation results show that with the increase of temperature, angular positions of the vibration mode axes obviously change, which leads to a dramatic zero bias drift. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…In this paper a finite element model of a Surface Acoustic Wave sensor is developed using ANSYS12© and tested for hydrogen detection. The sensor consists of a YZ-lithium niobate substrate with interdigital electrodes (IDT) patterned on the surface. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…In performing the analysis, simulated models of the magnetic field, the diaphragm displacement and the flow rate are developed using Ansoft/Maxwell3D, ANSYS FEA and FLUENT 6.3 CFD software, respectively. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Numerical study of the method was also investigated by using the finite element method (FEM) with ANSYS, resulting in reasonable agreement with the test data. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso