“…This paper presents a reduced beam section approach via the introduction of multilongitudinal voids (MLV) in the beam web for various beam depths varying from 450 mm to 912 mm. ANSYS finite element program was used to simulate the three different sizes of SAC sections: SAC3, SAC5, and SAC7. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…In light of the coupling of temperature, fluid, and stress, we get the thermo-fluid-solid model and governing equation. ANSYS-APDL was also used to stimulate the temperature influence on elastic modulus, Poisson ratio, uniaxial compressive strength, and permeability. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…MATERIAL AND METHODS: The three-dimensional (3D) finite element program (ANSYS software) was used to construct the mathematical model. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…CFD simulations for laminar flow of incompressible Newtonian fluid were conducted by using commercial software, ANSYS v15, with the rigid vascular wall assumption. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The mechanical behavior of aluminum hexagonal honeycombs subjected to out-of-plane dynamic indentation and compression loads has been investigated numerically using ANSYS/LS-DYNA in this paper. The finite element (FE) models have been verified by previous experimental results in terms of deformation pattern, stress-strain curve, and energy dissipation. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…In addition, 3D finite element model of the femur prepared from imaging data with both cortical and trabecular structures is delineated using MIMICS and ANSYS® and simulated as a composite structure. The damage accumulation occurring during cyclic loading was analyzed for fatigue scenario. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Simulation of the EWOD devices was conducted using ANSYS Fluent and showed the change in contact angle in response to voltage applied. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The overload acceleration (800 g) has been applied to the Finite-Element model in ANSYS, the contact process indicated that the proof mass contacted with stationary electrode three times, and there was no bounce phenomenon during contact process, which fully proved that the stable contact process can be realized at high acceleration owing to the designed elastic stationary electrode.…”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…In this work, an experimental campaign was carried out on high performance composite laminates with respect to the delamination mode I; subsequently, a numerical model representative of the experimental setup was built. The ANSYS Workbench Suite was used to simulate the delamination phenomena and modeFRONTIER was applied for the numerical/experimental calibration of the constitutive relationship on the basis of the delamination process, whose mechanism was implemented by means of the cohesive zone material (CZM) model.…”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…A sensitive element simulation model was built using ANSYS finite element simulation software to investigate the cross-interference of sensitivity for the proposed sensor. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The drag parameters for the ocean model were determined by comparing the simulation results from the ANSYS Fluent (®) software suite and SINMOD in an idealized channel setting with uniform currents. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The FE method was employed to calculate the magnetic field and power consumption by the ANSYS(®) version 12.1 software. Merit factors were defined in order to synthetically represent the ability of the simulated coil to trap beads for a unit power consumption, i.e. a given heat generation. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The simulations of the proposed antenna are carried out using Ansys HFSS software with a single-layer and multilayer human tissue models. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…We present an absorber design for KIDs sensitive to wavelengths of 10 [Formula: see text] shown to have around 75–80% absorption efficiency through ANSYS HFSS (high-frequency structure simulator) simulations, challenges that come with optimizing our design to increase the wavelength range, initial tests on our design of fabricated 10 [Formula: see text] KIDs, and theoretical NEP calculations.…”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Tunable RF filter is designed with detailed simulation using Ansys HFSS, and then correlated with measured results from experiment. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The archwire was modeled in Autodesk Inventor software and its behavior was simulated using the finite element code Ansys Workbench (Swanson Analysis Systems, Houston, Pennsylvania, USA). …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The flexibility matrix method and ANSYS are used to analyze the statics of the flexible drive mechanism. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Two models of two-dimensional (2D) type were constructed in ANSYS(®)2019 with circular and oval shape microparticles located inside the aluminum. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The numerical analysis on the free vibration characteristics of the composite was carried out using ANSYS, a finite element analysis (FEA) software. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The FEM is carried out using ANSYS™ software for the experiments, with vibration signal analysis by MUSIC algorithm. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso