“…A full parametric 3D model of a 2.5 Tm 4-layer CCT dipole has been developed using the APDL scripting in the ANSYS software. The, so called, bottom up approach with direct generation of nodes and elements has been utilized, optimizing for the speed of the model generation as the time consuming meshing was bypassed. …”
Enlace del recurso
Enlace del recurso

“…The 2D User-Defined Elements (UDEs) developed at Lawrence Berkeley National Laboratory in ANSYS Parametric Design Language, which support the multi-dependence material properties and include the effect of inter-filament coupling currents, are adapted and used in the coupled electrothermal, electrodynamic and electrical circuits calculations. …”
Enlace del recurso
Enlace del recurso

Enlace del recurso
Enlace del recurso

“…The data was produced with transient Eulerian modeling using Ansys Fluent 19.2. The simulations were done with one fluidization velocity and bed material, while the density, particle size, and inlet velocity of the secondary solid phase was varied and 10 simulations per each secondary solid phase case were simulated for 1 s, each simulation having different starting conditions (flow state of the air and bed material) inside the riser. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The proposed probes were simulated using Ansys HFSS and manufactured on a standard FR4 substrate four-layer printed circuit board (PCB). …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Curve fittings of surface stress and deflection based on ANSYS simulation results are performed to establish the sensor equations. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Furthermore, the optimization of the zigzag structure was performed with ANSYS DesignXplorer, and the results indicated that the total deformation could be decreased by 35.7% by optimizing the structure parameters, which would represent a significant advance of the radial stiffness of biodegradable polymeric stents.…”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The best results were obtained using the Trapezoid method in ANSYS with a constant step size and a resolution of 500 k points and using the Adams method in Mathcad with a resolution of 50 k points. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Considering the heat transfer behavior of thermoplastic fiber polyether ether ketone (PEEK) as the research object, a mathematical model of heat transfer in the thermoplastic composite fiber placement with the relevant boundary conditions was established. Ansys Parametric Design Language (APDL) was used to generate the finite element model and simulate the transient process, not only to explore the influence of various process parameters on the temperature field, but also to build an online temperature field measurement system. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…A high temperature rheometer with an air bearing was used for the tests, and ANSYS Fluent commercial software was used for numerical simulations. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Further, finite experimental element analysis of the GFRP angle sections was done using ANSYS software and validated with the experimental results. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Several finite element models of the IDEs piezoelectric actuator were established in ANSYS. The effect of branch electrodes on the strain of the actuator was analyzed. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The stator parameters were optimized by using ANSYS to obtain larger amplitudes for the ends of the driving feet in both X and Z directions. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The model is developed in ANSYS Fluent with customised user-defined-functions (UDFs), user-defined-scalar (UDS), and user-defined memory (UDM) codes to incorporate the cure kinetics and rheological characteristics of thermoset resin impregnation. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Taking the process of molten asphalt granulation as the research direction, this paper carries out an asphalt rotational viscosity experiment and a thermogravimetric differential thermal experiment (TG–DSC), and obtains the optimal temperature and viscosity values for the asphalt granulation process. The fluent module in ANSYS software is used to input the known asphalt and prilling tower parameters. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…In this method, the sample collection of strain measurement and deformation change at each measuring point of the flexible thin-walled structure was completed by ANSYS finite element analysis. The outliers were removed by the OCSVM (one-class support vector machine) model, and the unique mapping relationship between the strain value and the deformation variables (three directions of x-, y-, and z-axis) at each point was completed by a neural-network model. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Numerical simulations of projectile penetration into granite targets were conducted using the finite element program ANSYS/LS-DYNA. In terms of penetration depth and crater damage, the numerical simulation results agree well with the test data. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…A numerical model of the SHPB was established using the finite element software, ANSYS 19.0, and its reliability was verified by comparing it to laboratory test results. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…[Image: see text] To improve the efficiency of coal seam gas extraction, the influence characteristics of different factors on the penetration effect of cumulative blasting were determined and the hole spacing was effectively predicted; in this work, we used ANSYS/LS-DYNA numerical simulation software to establish the penetration model of cumulative blasting. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…On the implant's long axis, 150 N loads were applied both vertically and obliquely. ANSYS Workbench 18.0 and finite element software were used to compare the Von Mises stresses and deformation produced with a significance level of P < 0.05. …”
Enlace del recurso
Enlace del recurso