“…The experiments are validated using a numerical model developed in ANSYS.…”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…In this study, a 3D model of IGBT (Insulated Gate Bipolar Transistor) packaging was built by DesignModeler. Based on ANSYS Workbench, the influence of void size, location, solder layer type, and thickness on the temperature distribution of the IGBT module was simulated. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The mechanical impact characteristics of the model under different overloads were investigated using ANSYS/LS-DYNA, and the numerical simulation of the projectile intrusion into the three-layer concrete slab was carried out using LS-DYNA. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Material definition, 3D models editing, setting up analysis conditions, and constraints were performed using the Ansys 17.2 software. Gait biomechanics were taken into account to define the loading model, force distribution, force values, and constraints. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…METHODS: Fractographic method used for the failed chain indicates that over-stress was considered as the root cause of failure. 3D modeling and finite element analysis for the chain, used in a crane hook, were performed with a three-dimensional interactive application program, CATIA, commercial finite element analysis and computational fluid dynamic software, ANSYS. RESULTS: The results showed that the state of stress was changed depending on the initial position of the chain that was installed in the hook. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The fluid flow was simulated using FLUENT (ANSYS, PA, USA). Drag force and drag coefficient were calculated using (computational fluid dynamics) CFD in steady state. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The qualitative and quantitative evaluation of results obtained for the two-cell box girder is realized based on comparative analysis using the finite element method (FEM) and the ANSYS v12 software. The deflection function obtained by analytical and numerical methods was found consistent provided that the maximum deviation does not exceed 4%. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…With the aid of the finite element program ANSYS 8.0, the models were meshed and strictly vertical forces of 10 N were applied to each cusp tip. …”
Enlace del recurso
Enlace del recurso

“…KISS soft gear calculation software was used to determine the gear specifications and analysis is carried out in ANSYS software version.11.0 for the existing and the proposed gear to evaluate the performance of bending stress tooth deflection and stiffness. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The structural parameters of a controllable hydraulic cylinder type device were found by means of the computational fluid dynamics simulation performed by ANSYS CFX software. Parameters describing the magnetorheological fluid as non-Newtonian were determined by combining numerical and experimental research of the resistance force generated by the original magnetorheological damper. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The mechanical properties of the printed prosthesis were investigated using ANSYS software. RESULTS: The yield strength of the titanium-alloy prosthesis was 950 ± 14 MPa (mean ± SD), and its ultimate strength was 1005 ± 26 MPa. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The force (F) and moment (M) of both the loops were determined on 1 mm activation, using ANSYS software. M/F ratio was also calculated for both the loops. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The switch was modeled by ANSYS Workbench, and the simulation program was optimized for computational accuracy and speed. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Through the equivalent method, a laser bending model of SCLP is simulated by ANSYS software to predict the bending angle under different parameters. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…MATERIAL AND METHODS: 3 dimensional finite element study was carried out at first molar site with 4 surface coated and 4 non surface coated implants using mimic 8.11, solid edge 2004, hypermesh 9.0, and ansys12.1 software. RESULTS: The pattern of stress distribution was almost similar between vertical and oblique loading but varied with lateral loads between surface coated and non surface coated implants. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Then, the material properties were imported to ANSYS software to simulate the thermal deformation of the workpieces during processing. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…Secondly, a sensor bracket equipped with three thermal wind sensors was designed, the fluid dynamic response regularity of the measured wind field to the sensor bracket was analyzed using ANSYS Fluent CFD software, and then its structural parameters were optimized to improve measurement accuracy. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The computational fluid dynamics (CFD) tools were considered using ANSYS Fluent 16.2 software. This software exploits the finite volume method that is based on the resolution of the Navier-Stokes equations. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…In this sense, this work aims to study the oil–water mixture separation process using a new configuration of tubular ceramic membrane module by computational fluid dynamic (ANSYS Fluent software). The proposed model is composed of mass and linear momentum conservation equations coupled to Darcy’s law and SST k-ω turbulence model. …”
Enlace del recurso
Enlace del recurso
Enlace del recurso

“…The geometries were meshed and a computational fluid dynamics (CFD) analysis was performed using ANSYS. Results showed that major geometry bulk growth occurred in areas of low wall shear stress (WSS). …”
Enlace del recurso
Enlace del recurso
Enlace del recurso