Cargando…

Production of ultra-high-vacuum chambers with integrated getter thin-film coatings by electroforming

Titanium Zirconium Vanadium (TiZrV) thin film coatings are used in particle accelerators and synchrotron light sources to maintain ultra-high vacuum conditions. They are deposited on the internal walls of the vacuum chambers, transforming them from a gas source into a chemical pump. The trend in ele...

Descripción completa

Detalles Bibliográficos
Autor principal:	Lain Amador, Lucia
Lenguaje:	eng
Publicado:	2019
Materias:	Accelerators and Storage Rings Engineering
Acceso en línea:	https://dx.doi.org/10.17181/CERN.A2EJ.YIS2 http://cds.cern.ch/record/2693564

Ejemplares similares

Development of copper electroformed vacuum chambers with integrated non-evaporable getter thin film coatings
por: Amadora, Lucia Lain, et al.
Publicado: (2017)

Non-Evaporable Getter Thin Film Coatings for Vacuum Applications
por: Prodromides, A E
Publicado: (2002)

Decreasing surface outgassing by thin film getter coatings
por: Benvenuti, Cristoforo, et al.
Publicado: (1998)

Vacuum properties of TiZrV non-evaporable getter films
por: Benvenuti, Cristoforo, et al.
Publicado: (1999)

The Effect of Pulsed Current and Organic Additives on Hydrogen Incorporation in Electroformed Copper Used in Ultrahigh Vacuum Applications
por: Amador, L Lain, et al.
Publicado: (2019)

Efficient Combination of Surface Texturing and Functional Coating for Very Low Secondary Electron Yield Surfaces and Rough Nonevaporable Getter Films
por: Himmerlich, Marcel, et al.
Publicado: (2022)

Vacuum properties of TiZrV non-evaporable getter films [for LHC vacuum system]
por: Benvenuti, Cristoforo, et al.
Publicado: (2001)

A novel route to extreme vacua: the non-evaporable getter thin film coatings
por: Benvenuti, Cristoforo, et al.
Publicado: (1999)

Production of extreme high vacuum with non evaporable getters
por: Chiggiato, P
Publicado: (1994)

Influence of the substrate coating temperature on the vacuum properties of Ti-Zr-V non-evaporable getter films
por: Costa-Pinto, P, et al.
Publicado: (2003)

CERN Based $T_{c}$ Measurement Station for Thin-Film Coated Copper Samples and Results on Related Studies
por: Fonnesu, Dorothea, et al.
Publicado: (2022)

Hydrogen Embrittlement of TiZrV Non-Evaporable Getter Coating
por: Parragh, David Mate
Publicado: (2022)

Influence of the elemental composition and crystal structure on the vacuum properties of Ti-Zr-V non-evaporable getter films
por: Prodromides, A E, et al.
Publicado: (2001)

Deposition of thin superconducting coatings by means of ultra-high vacuum arc facilities
por: Sadowski, M J, et al.
Publicado: (2007)

NEG Thin Film Coating Development for the MAX IV Vacuum System
por: Grabski, Marek, et al.
Publicado: (2013)

Reverse coating technique for the production of Nb thin films on copper for superconducting radio-frequency applications
por: Fonnesu, D, et al.
Publicado: (2022)

XPS analysis of the activation process in non-evaporable getter thin films
por: Lozano, M, et al.
Publicado: (2000)

The secondary electron yield of TiZr and TiZrV non evaporable getter thin film coatings
por: Scheuerlein, C, et al.
Publicado: (2000)

Getter pumping
por: Benvenuti, C
Publicado: (2007)

Development and Production of Non-evaporable Getter Coatings for MAX IV
por: Costa Pinto, Pedro, et al.
Publicado: (2015)

Thin wall vacuum chamber in composite technique
por: Engelmann, G, et al.
Publicado: (1984)

Deposition of thin metal films by means of arc discharges under ultra-high vacuum conditions
por: Sadowski, M J, et al.
Publicado: (2007)

Progress in Use of Ultra-High Vacuum Cathodic Arcs for Deposition of Thin Film Superconducting Layers
por: Langner, J, et al.
Publicado: (2006)

Ceramic Vacuum Chambers: Determination of coating thickness for the MedAustron kicker magnets vacuum chambers
por: Stadlbauer, T, et al.
Publicado: (2011)

Technical specification for a thin wall vacuum chamber
por: Wahl, H
Publicado: (1983)

International Symposium on Vacuum and Thin-film Technology
por: Collective
Publicado: (1977)

Industrial fabrication of ultra-high-vacuum quadrupole chambers for LEP
por: Brunet, J C
Publicado: (1990)

Measurement of Ultra Low Outgassing Rates for NLC UHV Vacuum Chambers
por: Kishiyama, K, et al.
Publicado: (2001)

Development of Titanium Nitride Coating for SNS Ring Vacuum Chambers
por: Todd, R, et al.
Publicado: (2001)

Note on proposition for thin-walled metallic ondulated chamber to replace large aperture ceramic vacuum chambers
por: Mann, P H
Publicado: (1978)

Ion-stimulated Gas Desorption Yields of Electropolished, Chemically Etched, and Coated (Au, Ag, Pd, TiZrV) Stainless Steel Vacuum Chambers and St707 Getter Strips Irradiated with 4.2 MeV/u lead ions
por: Mahner, E, et al.
Publicado: (2005)

Ultra-high vacuum chamber
por: CERN PhotoLab
Publicado: (1967)

Outgassing and Surface Properties of TiN Coated SNS Ring Vacuum Chambers
por: Hseuh, H, et al.
Publicado: (2003)

Ultimate pressures achieved in TiZrV sputter-coated vacuum chambers
por: Benvenuti, Cristoforo, et al.
Publicado: (1999)

Booster Vacuum system - Chamber to Chamber Insulation
por: Unterlerchner, W
Publicado: (1968)

Principles of electroplating and electroforming (electrotyping)
por: Blum, William, et al.
Publicado: (1949)

Computation of stress and deflections of elliptical vacuum chambers with corrugated thin wall profile of variable amplitude
por: Brianti, G, et al.
Publicado: (1969)

Vacuum chamber apertures for the PSB
por: Bovet, C
Publicado: (1969)

Vacuum chambers in composite material
por: Engelmann, G, et al.
Publicado: (1987)

The impedance of layered vacuum chambers
por: Keil, Eberhard, et al.
Publicado: (1998)

Cannot write session to /tmp/vufind_sessions/sess_e8pbu2qvdt3pup588gurggqbr2