Cargando…

Wire bonding work at CERN

Wire bonding work at CERN

Detalles Bibliográficos
Publicado:	2006
Materias:	ITS
Acceso en línea:	http://cds.cern.ch/record/975487

Ejemplares similares

Wire bonding of the MCM multi chip module using 25 micron wire at CERN.
por: Saba, A
Publicado: (2006)

ALICE ladder mounted and wire bonded on prototype bus
Publicado: (2002)

In the photograph, one can see the interconnection from one readout chip to the flexible cable realized with ultrasonic wire bonds (25 microns).
por: Saba, A
Publicado: (2006)

Hybrid bonding on K&S manual bonder
por: Alessandro, B.
Publicado: (2004)

Alice Silicon Strip Detector, HAL bonding tool
por: xxx, x
Publicado: (2002)

SEM picture of bump bonding pads on ALICE readout chip
Publicado: (2002)

Front-end chip cable and jif on Delvotec (bonding machine)
por: Alessandro, B.
Publicado: (2004)

ALICE Pixel Ladder (5 chips bump bonded to 1 sensor) mounted on prototype bus
Publicado: (2002)

ALICE Testbeam 2002-Reference plane made of 2 bump bonded single chip assemblies
Publicado: (2002)

Alice Silicon Strip Detector at CERN
por: xxx, x
Publicado: (2006)

View of the control room at the CERN Divisional Silicon Facilty
por: Saba, A
Publicado: (2006)

Alice Silicon Strip Detector, work in Alice magnet
por: xxx, x
Publicado: (2006)

A few members of the Silicon Pixel Detector working on the completed first half barrel
por: Saba, A
Publicado: (2007)

Members of the ALICE Pixel team testing the second sector of the ALICE Silicon Pixel Detector in the divisional silicon facility laboratory at CERN
por: Saba, A
Publicado: (2006)

Working of the 1st supermodule of the the PHOS photon spectrometer which contasins 3584 lead tungstate crystals. One crystal is 18 centimetre long and weighs some 750 grams.
por: Saba, A
Publicado: (2006)

Working of the 1st supermodule of the the PHOS photon spectrometer which contains 3584 lead tungstate crystals. One crystal is 18 centimetre long and weighs some 750 grams. Photo: Antonio Saba. Photographer. www.antoniosaba.com
por: Saba, Antonio
Publicado: (2006)

ALICE ITS Silicon Strip Module
Publicado: (2006)

Alice Silicon Strip Detector, Endcap supports
por: xxx, x
Publicado: (2006)

Alice Silicon Strip Detector, last inspection
por: xxx, x
Publicado: (2006)

Alice Silicon Strip Detector, patch panel
por: xxx, x
Publicado: (2006)

Assembly of the ALICE Silicon Strip Detector
por: xxx, x
Publicado: (2006)

Shipment of Silicon Strip Detector
por: xxx, x
Publicado: (2006)

Test mounting of Silicon Strip Detector
por: xxx, x
Publicado: (2006)

Alice Silicon Strip Detector, Pillar test
por: xxx, x
Publicado: (2006)

Preparation of Silicon Strip Detector to transport
por: xxx, x
Publicado: (2006)

Alice Silicon Strip Detector, Cone in Torino
por: xxx, x
Publicado: (2006)

Alice Silicon Strip Detector, setting up the test
por: xxx, x
Publicado: (2006)

Module of the Silicon Drift Detector of ALICE
por: Saba, A.
Publicado: (2006)

Alice Silicon Strip Detector, preparation of ladder cable
por: xxx, x
Publicado: (2006)

Full-scale model of the ALICE ITS Detector
Publicado: (2004)

ALICE ITS
Publicado: (2003)

ALICE pixel prototype bus with 10 readout chips
Publicado: (2002)

ALICE pixel readout chip with 8192 readout channels
Publicado: (2001)

ALICE ITS Testbeam setup with 4 pixel reference planes
Publicado: (2002)

ALICE ITS
Publicado: (2003)

ALICE Carbon fibre sector support
Publicado: (2001)

ALICE ladder mounted on prototype bus
Publicado: (2002)

Probing of ALICE single chip assembly
Publicado: (2001)

Multiple trigger scintillators were installed: big ones covering the total surface of the sensor and several smaller ones. The former give a trigger for each beam particle. The latter are used to select a part of the sensor surface for efficiency measurements.
por: Nooren, G.
Publicado: (2004)

In ALICE particles will hit the sensors at oblique angles. This is partly simulated here by rotating the modules.
por: Nooren, G.
Publicado: (2004)

Cannot write session to /tmp/vufind_sessions/sess_1mk85ika980g329vorlff62f09