Cargando…

The Effect of Zn and Zn–WO(3) Composites Nano-Coatings Deposition on Hardness and Corrosion Resistance in Steel Substrate

Pure Zn (Zinc) and its Zn–WO(3) (Zinc–Tungsten trioxide) composite coatings were deposited on mild steel specimens by applying the electrodeposition technique. Zn–WO(3) composites were prepared for the concentration of 0.5 and 1.0 g/L of particles. The influence of WO(3) particles on Zn deposition,...

Descripción completa

Detalles Bibliográficos
Autores principales:	Kumar, Channagiri Mohankumar Praveen, Chandrashekarappa, Manjunath Patel Gowdru, Kulkarni, Raviraj Mahabaleshwar, Pimenov, Danil Yurievich, Giasin, Khaled
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2021
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC8123838/ https://www.ncbi.nlm.nih.gov/pubmed/33925537 http://dx.doi.org/10.3390/ma14092253

Ejemplares similares

Corrosion Behaviour of High-Strength Al 7005 Alloy and Its Composites Reinforced with Industrial Waste-Based Fly Ash and Glass Fibre: Comparison of Stir Cast and Extrusion Conditions
por: Swamy, Praveen Kumar, et al.
Publicado: (2021)

Image Processing of Mg-Al-Sn Alloy Microstructures for Determining Phase Ratios and Grain Size and Correction with Manual Measurement
por: Ercetin, Ali, et al.
Publicado: (2021)

Analysis and Optimization of Dimensional Accuracy and Porosity of High Impact Polystyrene Material Printed by FDM Process: PSO, JAYA, Rao, and Bald Eagle Search Algorithms
por: Chandrashekarappa, Manjunath Patel Gowdru, et al.
Publicado: (2021)

Microstructure, Mechanical, and Corrosion Behavior of Al(2)O(3) Reinforced Mg2Zn Matrix Magnesium Composites
por: Ercetin, Ali, et al.
Publicado: (2021)

Modeling of Cutting Parameters and Tool Geometry for Multi-Criteria Optimization of Surface Roughness and Vibration via Response Surface Methodology in Turning of AISI 5140 Steel
por: Kuntoğlu, Mustafa, et al.
Publicado: (2020)

Study of a Multicriterion Decision-Making Approach to the MQL Turning of AISI 304 Steel Using Hybrid Nanocutting Fluid
por: Dubey, Vineet, et al.
Publicado: (2021)

Effect of Cryogenic Grinding on Fatigue Life of Additively Manufactured Maraging Steel
por: Balan, Arunachalam S. S., et al.
Publicado: (2021)

Elucidating the Effect of Step Cooling Heat Treatment on the Properties of 2.25 Cr–1.0 Mo Steel Welded with a Combination of GMAW Techniques Incorporating Metal-Cored Wires
por: Das, Subhash, et al.
Publicado: (2021)

Establishing the Relationship between Cutting Speed and Output Parameters in Belt Grinding on Steels, Aluminum and Nickel Alloys: Development of Recommendations
por: Syreyshchikova, Nelli Vladimirovna, et al.
Publicado: (2021)

Relationship between Pressure and Output Parameters in Belt Grinding of Steels and Nickel Alloy
por: Syreyshchikova, Nelli Vladimirovna, et al.
Publicado: (2021)

Corrosion Resistance and Surface Bioactivity of Ti6Al4V Alloy after Finish Turning under Ecological Cutting Conditions
por: Leksycki, Kamil, et al.
Publicado: (2021)

Experimental Investigations and Effect of Nano-Powder-Mixed EDM Variables on Performance Measures of Nitinol SMA
por: Chaudhari, Rakesh, et al.
Publicado: (2022)

Evaluation of Mechanical and Tribological Aspect of Self-Lubricating Cu-6Gr Composites Reinforced with SiC–WC Hybrid Particles
por: Usca, Üsame Ali, et al.
Publicado: (2022)

Optimization and Analysis of Surface Roughness, Flank Wear and 5 Different Sensorial Data via Tool Condition Monitoring System in Turning of AISI 5140
por: Kuntoğlu, Mustafa, et al.
Publicado: (2020)

Development of an Oxide Layer on Al 6061 Using Plasma Arc Electrolytic Oxidation in Silicate-Based Electrolyte
por: Jadhav, Priya, et al.
Publicado: (2022)

Tribological Aspects, Optimization and Analysis of Cu-B-CrC Composites Fabricated by Powder Metallurgy
por: Usca, Üsame Ali, et al.
Publicado: (2021)

Surface Roughness Evaluation in Thin EN AW-6086-T6 Alloy Plates after Face Milling Process with Different Strategies
por: Chuchala, Daniel, et al.
Publicado: (2021)

Measurement of Micro Burr and Slot Widths through Image Processing: Comparison of Manual and Automated Measurements in Micro-Milling
por: Akkoyun, Fatih, et al.
Publicado: (2021)

Hand and Abrasive Flow Polished Tungsten Carbide Die: Optimization of Surface Roughness, Polishing Time and Comparative Analysis in Wire Drawing
por: Kumar, Raman, et al.
Publicado: (2022)

Multi-Response Optimization of Al(2)O(3) Nanopowder-Mixed Wire Electrical Discharge Machining Process Parameters of Nitinol Shape Memory Alloy
por: Chaudhari, Rakesh, et al.
Publicado: (2022)

Parametric Optimization and Influence of Near-Dry WEDM Variables on Nitinol Shape Memory Alloy
por: Chaudhari, Rakesh, et al.
Publicado: (2022)

Influence of Different Grades of CBN Inserts on Cutting Force and Surface Roughness of AISI H13 Die Tool Steel during Hard Turning Operation
por: Kumar, Pardeep, et al.
Publicado: (2019)

Performance Assessment of Minimum Quantity Castor-Palm Oil Mixtures in Hard-Milling Operation
por: Sen, Binayak, et al.
Publicado: (2021)

Optimization and Modeling of Material Removal Rate in Wire-EDM of Silicon Particle Reinforced Al6061 Composite
por: Doreswamy, Deepak, et al.
Publicado: (2021)

Towards Analysis and Optimization for Contact Zone Temperature Changes and Specific Wear Rate of Metal Matrix Composite Materials Produced from Recycled Waste
por: Güneş, Aydın, et al.
Publicado: (2021)

Evaluation of the Mechanical Properties and Drilling of Glass Bead/Fiber-Reinforced Polyamide 66 (PA66)-Based Hybrid Polymer Composites
por: Demirsöz, Recep, et al.
Publicado: (2022)

Optimization Study on Surface Roughness and Tribological Behavior of Recycled Cast Iron Reinforced Bronze MMCs Produced by Hot Pressing
por: Güneş, Aydın, et al.
Publicado: (2021)

Joining of Dissimilar Al and Mg Metal Alloys by Friction Stir Welding
por: Sidhu, Ramandeep Singh, et al.
Publicado: (2022)

Evaluation of Cutting-Tool Coating on the Surface Roughness and Hole Dimensional Tolerances during Drilling of Al6061-T651 Alloy
por: Al-Tameemi, Hamza A., et al.
Publicado: (2021)

Effect of Fibre Orientation on Impact Damage Resistance of S2/FM94 Glass Fibre Composites for Aerospace Applications: An Experimental Evaluation and Numerical Validation
por: Giasin, Khaled, et al.
Publicado: (2021)

Integration of Fuzzy AHP and Fuzzy TOPSIS Methods for Wire Electric Discharge Machining of Titanium (Ti6Al4V) Alloy Using RSM
por: Fuse, Kishan, et al.
Publicado: (2021)

The chemistry of ZnWO(4) nanoparticle formation
por: Bøjesen, Espen D., et al.
Publicado: (2016)

Empirical Investigations during WEDM of Ni-27Cu-3.15Al-2Fe-1.5Mn Based Superalloy for High Temperature Corrosion Resistance Applications
por: Aggarwal, Vivek, et al.
Publicado: (2020)

Machine Learning Modelling and Feature Engineering in Seismology Experiment
por: Brykov, Michail Nikolaevich, et al.
Publicado: (2020)

Optimization of Machining Parameters to Minimize Cutting Forces and Surface Roughness in Micro-Milling of Mg13Sn Alloy
por: Ercetin, Ali, et al.
Publicado: (2023)

The Role of Observation–Measurement Methods in the Surface Characterization of X39Cr13 Stainless-Steel Cutting Blades Used in the Fish Processing Industry
por: Kapłonek, Wojciech, et al.
Publicado: (2020)

A Soft Computing-Based Analysis of Cutting Rate and Recast Layer Thickness for AZ31 Alloy on WEDM Using RSM-MOPSO
por: Goyal, Kapil K., et al.
Publicado: (2022)

Cubic Lattice Structures of Ti6Al4V under Compressive Loading: Towards Assessing the Performance for Hard Tissue Implants Alternative
por: Dhiman, Sahil, et al.
Publicado: (2021)

Effect of Al–Zn Alloy Coating on Corrosion Fatigue Behavior of X80 Riser Steel
por: Han, Zhongying, et al.
Publicado: (2019)

Microstructure and Corrosion Resistance of Zn-Al Diffusion Layer on 45 Steel Aided by Mechanical Energy
por: Tong, Jianbin, et al.
Publicado: (2019)

Cannot write session to /tmp/vufind_sessions/sess_6qjiam0hli1jiqj8103mk7u9ts